Energy Walk-off in Nonlinear Acoustics

It is found that acoustic internal conical refraction occurs for both fundamental and second harmonic of transverse wave propagating dong threefold axis of crystals.Energy walk-off which usually does not exist in acoustic collinear harmonic generation appears as well.

A simulation method on target strength and circular SAS imaging of Xrudder UUV including multiple acoustic scattering

Target strength(TS)and circular synthetic aperture sonar(CSAS)images provide essential information for active acoustic detection and recognition of non-cooperative unmanned undersea vehicles(UUVs),which pose a significant threat to underwater preset facilities.To access them,we propose an iterative physical acoustics(IPA)-based method to simulate the multiple acoustic scattered fields on rigid surfaces in high-frequency cases.It uses the Helmholtz integral equation with an appropriate Green's function in terms of the Neumann series,and then incorporates the ideas of triangulation and iteration into a numerical implementation.Then two approximate analytic formulae with precise physical meanings are derived to predict the TS and CSAS images of concave targets,respectively.There are no restrictions on the surface's curvature and the order of multiple scattering.The method is validated against the finite element method(FEM)for acoustic scattering from a sphere segment and against an experiment involving an X-rudder UUV's stern.On this basis,we simulate and analyze the TS and CSAS images of an X-rudder UUV.In addition,the influence of the angle of adjacent rudders on the multiple scattering characteristics is discussed.Results show that this method can potentially predict accurate UUV features,especially the multiple scattered features.

嘈杂语噪声下汉语整句识别的同质性研究

目的获得嘈杂语噪声背景下汉语短句识别率-信噪比(Performance-Intensity,P-I)函数的斜率和50%的得分所对应的信噪比(记为SNR50),并对所有短句的同质性进行评估和调整。方法采用16张(每张20句)新编嘈杂语噪声下汉语普通话短句识别表作为测试材料。选取年龄为21～25岁之间、听力/言语发育正常且日常以汉语普通话为交流方式的48名受试者按"随机区组设计"在-1、-4、-7、-10dB四种信噪比条件下进行言语识别率的心理声学测量。使用Statistica7.0软件进行P-I函数拟合和统计分析。结果320句语句在嘈杂语噪声下的言语识别P-I函数曲线的阈值呈正态分布,斜率呈不规则分布。剔除P-I函数强健性增长(斜率>55%/dB)的语句,并保留阈值变异度在±2!内的语句,精选出同质性良好的240句。结论逐个调整每句的SNR以实现同质性,可为编制"等言语识别阈级"的句表奠定扎实的心理声学基础。

Frequency Diversity for OFDM Mobile Communication via Underwater Acoustic Channels

The major constraint on the performance of orthogonal frequency division multiplexing （OFDM） based underwater acoustic （UWA） communication is to keep subcarriers orthogonal. In this paper, Doppler estimation and the respective compensation technique along with various diversity techniques were deliberated for OFDM-based systems best suited for underwater wireless information exchange. In practice, for mobile communication, adjustment and tuning of transducers in order to get spatial diversity is extremely difficult. Considering the relatively low coherence bandwidth in UWA, the frequency diversity design with the Doppler compensation function was elaborated here. The outfield experiments of mobile underwater acoustic communication （UWAC） based on OFDM were carried out with 0.17 bit/（s-Hz） spectral efficiency. The validity and the dependability of the scheme were also analyzed.

Seismic isolation effect of lined circular tunnels with damping treatments

The Havriliak-Negami model for dynamic viscoelastic material behavior and Biot＇s theory of poroelasticity are employed to develop an exact solution for three-dimensional scattering effect of harmonic plane P-SV waves from a circular cavity lined with a multilayered fluid-filled shell of infinite length containing viscoelastic damping materials and embedded within a fluid-saturated permeable surrounding soil medium. The analytical results are illustrated with numerical examples where the effects of liner/coating structural arrangement, viscoelastic material properties, liner-soil interface bonding condition, seismic excitation frequency, and angle of incidence on the induced dynamic stress concentrations are evaluated and discussed to obtain representative values of the parameters that characterize the system. It is demonstrated that incorporating viscoelastic damping materials with a low shear modulus in the constrained layer configuration is an efficient means of enhancing the overall seismic isolation performance, especially for near-normally incident seismic shear waves where the amplitudes of induced dynamic stresses may be reduced by up to one-third of those without isolation in a relatively wide frequency range. Some additional cases are considered and good agreements with solutions available in the literature are obtained.

Research of Underwater Bottom Object and Reverberation in Feature Space

The critical technical problem of underwater bottom object detection is founding a stable feature space for echo signals classification. The past literatures more focus on the characteristics of object echoes in feature space and reverberation is only treated as interference. In this paper, reverberation is considered as a kind of signal with steady characteristic, and the clustering of reverberation in frequency discrete wavelet transform （FDWT） feature space is studied. In order to extract the identifying information of echo signals, feature compression and cluster analysis are adopted in this paper, and the criterion of separability between object echoes and reverberation is given. The experimental data processing results show that reverberation has steady pattern in FDWT feature space which differs from that of object echoes. It is proven that there is separability between reverberation and object echoes.

Effect of Sound Source Scattering on Measurement of Near-Field Head-Related Transfer Functions

A simple spherical bead and pulsating spherical sound source model are proposed to investigate the effect of multiple scattering between the head and the sound source on near-field head-related transfer function （HRTF） measurement. Multipole expansion method is used to calculate HRTFs of the model, then the relationships among the magnitude error of HRTF with frequency, source direction, source size, and the distance between the head centre and the sound source are analysed. The results show that to ensure the magnitude error of HRTF within 1.0dB up to 20kHz, for source distance not less than 0.15m or 0.20m, the radius of the sound source should not exceed 0.03 m or 0.05 m, respectively. The conclusion suggests an appropriate size of sound source in near-field HRTF measurement.

Analysis of SNR for Acoustic Vector Sensor Linear Array in Volume and Surface-generated Noise Fields

Acoustic vector sensor consists of pressure and particle velocity sensors,which measure the three-dimensional acoustic particle velocity,as well as the pressure at one location at the same time.By preserving the amplitude and phase information of the pressure and particle velocity,they possess a number of advantages over traditional scalar sensors.Signal-to-noise ratio (SNR) gain (which is often called array gain) is one of such advantages and is always interested by all of us.But it is not unchangeable if the spatial correlation of the noise field varies.Much more important,it is difficult to be given if the noise becomes complex.In this paper,spatial correlation of the vector field of isotropic volume-noise and surface-generated noise has been introduced briefly.Based on the results,the combined SNR output of a vector linear array is investigated and the maximum gain is given in the specified noise.Computer simulation shows that the output of one array in the same noise is not the same in different gestures.And then we find the best gesture through SNR calculation and obtain the biggest gain,which has important meaning to guide how to deploy an array in practice.We also should use the array with respect to the characteristics of the real ambient noise,especially in anisotropic noise field.

A geometric Model for the Spatial Correlation of an Acoustic Vector Field in Surface-generated Noise

Spatial correlation of sound pressure and particle velocity of the surface noise in horizontally stratified media was demonstrated, with directional noise sources uniformly distributed on the ocean surface. In the evaluation of particle velocity, plane wave approximation was applied to each incident ray. Due to the equivalence of the sound source correlation property and its directivity, solutions for the spatial correlation of the field were transformed into the integration of the coherent function generated by a single directional source. As a typical horizontally stratified media, surface noise in a perfect waveguide was investigated. Correlation coefficients given by normal mode and geometric models show satisfactory agreement. Also, the normalized covariance between sound pressure and the vertical component of particle velocity is proportional to acoustic absorption coefficient, while that of the surface noise in semi-infinitely homogeneous space is zero.

Classification of Underwater Target Echoes Based on Auditory Perception Characteristics

In underwater target detection, the bottom reverberation has some of the same properties as the target echo, which has a great impact on the performance. It is essential to study the difference between target echo and reverberation. In this paper, based on the unique advantage of human listening ability on objects distinction, the Gammatone filter is taken as the auditory model. In addition, time-frequency perception features and auditory spectral features are extracted for active sonar target echo and bottom reverberation separation. The features of the experimental data have good concentration characteristics in the same class and have a large amount of differences between different classes, which shows that this method can effectively distinguish between the target echo and reverberation.

Directivity of Spherical Polyhedron Sound Source Used in Near-Field HRTF Measurements

The omnidirectional character is one of important requirements for the sound source used in near-field head- related transfer function （HRTF） measurements. Based on the analysis on the radiation sound pressure and directivity character of various spherical polyhedron sound sources, a spherical dodecahedral sound source with radius of O. 035 m is proposed and manufactured. Theoretical and measured results indicate that the sound source is approximately omnidirectional below the frequency of 8 kHz. In addition, the sound source has reasonable magnitude response from 350Hz to 20 kHz and linear phase characteristics. Therefore, it is suitable for the near-field HRTF measurements.

Measurement of the Elasticity of Biological Soft Tissue of Finite Thickness

Elasticity is of profound significance to evaluating the function of a biological soft tissue. When the elasticity of a tissue is macroscopically changed, it means that the biological function of the tissue is abnormal and some disease or injury may occur. In the present work, an elastometer is developed to measure the elasticity of biological soft tissues. The measurement is based on the indentation method and the force is measured by the bending of the cantilever. The force-indentation data of the soft tissue is experimentally measured by this elastometer and Young＇s modulus of the tissue is calculated using the Hertz-Sneddon model. For comparison, a numerical model for the indentation method is established using the finite element method. The difference between the actual modulus and the measured modulus is discussed. The effect of the thickness of the specimen on the measurement is investigated. Young＇s moduli of beef, porcine liver and porcine kidney are experimentally measured. The results indicate that our elastometer is effective in measuring Young＇s modulus of a soft tissue quantitatively.

Frequency domain polarization weighted ESPRIT method for bearing angle

The signal to noise ratio （SNR） of seismic waves is usually very low after long distance transmission. For this condition, to improve the bearing estimation capability in the low SNR, a frequency domain polarization weighted ESPRIT method using a single vector device is proposed. The frequency domain polari- zation parameters extracted from the signals are used to design the weighted function which is applied to the received signals. The bearing angle and the target frequency are estimated through ESPRIT using the weighted signals. The simulation and experiment results show that the presented method can obtain accurate estimation values under the low SNR with little prior information.

Analytical solution based on the wavenumber integration method for the acoustic field in a Pekeris waveguide

An exact solution based on the wavenumber integration method is proposed and implemented in a numerical model for the acoustic field in a Pekeris waveguide excited by either a point source in cylindrical geometry or a line source in plane geometry. Besides, an unconditionally stable numerical solution is also presented, which entirely resolves the stability problem in previous methods. Generally the branch line integral contributes to the total field only at short ranges, and hence is usually ignored in traditional normal mode models. However, for the special case where a mode lies near the branch cut, the branch line integral can contribute to the total field significantly at all ranges. The wavenumber integration method is well-suited for such problems. Numerical results are also provided, which show that the present model can serve as a benchmark for sound propagation in a Pekeris waveguide.

Numerical Simulation of Viscous Cavitating Flow Around A Ship Propeller

In the present study, cavitation and a ship propeller wake are reported by computed fluid dynamics based on viscous multiphase flow theory. Some recent validation results with a hybrid grid based on unsteady Navier-Stokes （N-S） and bubble dynamics equations are presented to predict velocity, pressure and vapor volume fraction in propeller wake in a uniform inflow. Numerical predictions of sheet cavitation, tip vortex cavitation and hub vortex cavitation are in agreement with the experimental data, same as numerical predictions of longitudinal and transversal evolution of the axial velocity. Blade and shaft rate frequency of propeller is well predicted by the computed results of pressure, and tip vortex is the most important to generate the pressure field within the near wake. The overall results indicate that the present approach is reliable for prediction of cavitation and propeller wake on the condition of uniform inflow.

Performance Evaluation and Effectiveness of the Reverberation Room

This research presents a thorough evaluation of the reverberation room at Acoustics Laboratory in National Institute of Standards(NIS)according to the related international standards.The evaluation aims at examining the room performance and exploring its effectiveness in the frequency range from 125 Hz to 10000 Hz according to the international standard requirements.The room,which was designed and built several years ago,is an irregular rectangular shape free from diffusers.Its volume is about 158.84 m^(3),which meets the requirement of the ISO 354 standard Lmax<1.9V^(1/3).Cut-off frequencies of one and one-third octave are 63 Hz and 100 Hz respectively;however Schroder frequency is 400 Hz.Calculations of cut-off frequency and modal density showed adequate modes that give acceptable uniformity starting comfortably from frequency of 125 Hz.The room has a reverberation time that is suitable for its size over the frequency range of interest.The room sound absorption surface area and its sound absorption coefficient satisfy the criteria given in ISO 3741 and ISO 354.There is an accepted diffuse sound field inside the room due to the standard deviation of measured sound level,which is less than 1.5 dB over all the frequency range.The only exception was 125 Hz which may be due to a lack of diffusivity of the sound field at this frequency.The evaluation proves that the NIS reverberation room is in full agreement with the international standards,which in turns qualifies the room to host measurements inside without concerns.

Method for Measuring Self-noise of Vector Hydrophones

The Vector Hydrophone(VH) is widely used to remotely detect underwater targets. Accurately measuring the self-noise of the VH provides an important basis for evaluating the performance of the detection system in which it is utilized, since the ability to acquire weak signals is determined by the VH self-noise level. To accurately measure the VH self-noise level in actual working conditions, the Dual-channel Transfer Function Method(DTFM) is proposed to reduce ambient background noise interference. In this paper, the underlying principles of DTFM in reducing ambient background noise is analyzed. The numerical simulations to determine the influence of ambient background noise, and the sensitivity difference of the two VHs on the measurement results are studied. The results of measuring the VH self-noise level in a small laboratory water tank by using DTMF indicate that ambient background noise interference can be reduced effectively by employing DTMF, more accurate self-noise level can be obtained as well. The DTMF provides an effective method for accurately measuring the self-noise level of VHs and also provides technical support for the practical application of the VH in underwater acoustics.

Theoretical and Experimental Study on the Acoustic Wave Energy After the Nonlinear Interaction of Acoustic Waves in Aqueous Media

Based on the Burgers equation and Manley-Rowe equation, the derivation about nonlinear interaction of the acoustic waves has been done in this paper. After nonlinear interaction among the low-frequency weak waves and the pump wave, the analytical solutions of acoustic waves＇ amplitude in the field are deduced. The relationship between normalized energy of high-frequency and the change of acoustic energy before and after the nonlinear interaction of the acoustic waves is analyzed. The experimental results about the changes of the acoustic energy are presented. The study shows that new frequencies are generated and the energies of the low-frequency are modulated in a long term by the pump waves, which leads the energies of the low-frequency acoustic waves to change in the pulse trend in the process of the nonlinear interaction of the acoustic waves. The increase and decrease of the energies of the low-frequency are observed under certain typical conditions, which lays a foundation for practical engineering applications.

Damping Analysis and Failure Mechanism of 3D Printed Bio-Based Sandwich with Auxetic Core under Bending Fatigue Loading

Meta-sandwich composites with three-dimensional(3D)printed architecture structure are characterized by their high ability to absorb energy.In this paper,static and fatigue 3-point bending tests are implemented on a 3D printed sandwich composites with a re-entrant honeycomb core.The skins,core and whole sandwich are manufactured using the same bio-based material which is polylactic acid with flax fiber reinforcement.Experimental tests are performed in order to evaluate the durability and the ability of this material to dissipate energy.First,static tests are conducted to study the bending behaviour of the sandwich beams,as well as to determine the failure parameters and the characteristic used in fatigue tests.Then,fatigue analyses were carried out to determine the fatigue resistance of these structures.The effects of the core density on the stiffness,hysteresis loop,energy absorption and loss factor,for two loading level,are determined.Moreover,the behaviour of this sandwich composite with re-entrant honeycomb core is compared with that of sandwiches with different core topologies.The results show that sandwich with high core density dissipate more energy,which results higher loss factors.The determined properties offer the most sensitive indicators of sandwich composite damage during its lifetime.This work aims to determine the static and fatigue properties of this material,thus,study its potential applications in industry.

Laser-Generated Transient Lamb Wave in Thin Plates

The laser-generated transient Lamb wave in thin isotropic plates is studied theoretically by employing the method of eigenfunction expansion.The thermoelastic displacement field is expressed by symmetric and antisymmetnc Lamb wave modes,so that it is convenient to investigate thg transient excitation of the lowest and higher order Lamb wave modes.The characteristics of transient Lamb waves in thin materials with different thicknesses are discussed in details.