Silica aerogels are light weight, nanostructured, and highly porous materials with an open pore structure. Due to their excellent characteristics, such as extremely low thermal conductivity, low density and high poros...Silica aerogels are light weight, nanostructured, and highly porous materials with an open pore structure. Due to their excellent characteristics, such as extremely low thermal conductivity, low density and high porosity, the silica aerogels become promising potential adsorbents, catalysts, thermal insulation, and acoustic absorption materials for environmental purposes. This paper presents the synthesis of a highly flexible polymer modified silica aerogel with the use of a cellulose-methyltriethoxysilane (MTES) precursor in a two-step acid-base catalyzed sol-gel process. The physical properties of the resulting aerogels were characterized by thermogravimetry, scanning electron microscopy, nitrogen adsorption-desorption, contact angle, thermal conductivity measurements, compression testing and Fourier transform infrared spectroscopy. The fabricated aerogel exhibited high flexibility with a Young’s modulus of compression of 0.33 MPa and the density of 0.132 g/cm3. They were hydrophobic in nature and had low thermal conductivity. Preparation of aerogel with solid waste (fly ash/bottom ash) is also discussed. The preliminary results showed that the materials have great potential for environmental application, i.e. enhancement of solid waste recycling rate by converting waste to high value-added materials, super thermal and acoustic insulation materials in green building and removal of oil spilled into surface drainage.展开更多
Micro arc oxidation(MAO)coatings were formed on magnesium alloy AZ31B to improve the corrosion resistance using environmental friendly electrolyte solution under single-polar pulse power supply.The effect of electrica...Micro arc oxidation(MAO)coatings were formed on magnesium alloy AZ31B to improve the corrosion resistance using environmental friendly electrolyte solution under single-polar pulse power supply.The effect of electrical parameters of pulse frequency on the coating performance was studied at frequencies of 2.5 Hz,25 Hz and 250 Hz.The coating performance at different frequencies was characterized by scanning electron microscopy(SEM),energy-dispersive X-ray spectroscopy(EDS)and potentiodynamic polarization testing method.It was found that the corrosion resistance of the MAO coatings was improved when increasing the pulse frequencies from 2.5 Hz to 250 Hz.The corrosion current in 250 Hz case decreased by three orders of magnitude as compared with bare Mg alloy and the corrosion impedance also increased remarkably,means significantly enhanced corrosion resistance than bare Mg alloy.The results give us more insight in the optimization of electrical parameters to improve the MAO coating performance.The MAO technology is attractive for application on magnesium and other light alloys for surface protection in automotive and space industries.展开更多
A flexible counter electrode(CE) for dye-sensitized solar cells(DSCs) has been fabricated using a micro-porous polyvinylidene fluoride membrane as support media and sputtered Pt as the catalytic material.Non-conventio...A flexible counter electrode(CE) for dye-sensitized solar cells(DSCs) has been fabricated using a micro-porous polyvinylidene fluoride membrane as support media and sputtered Pt as the catalytic material.Non-conventional structure DSCs have been developed by the fabricated CEs. The Pt metal was sputtered onto one surface of the membrane as the catalytic material. DSCs were assembled by attaching the Ti O2 electrode to the membrane surface without Pt coating. The membrane was with cylindrical pore geometry. It served not only as a substrate for the CE but also as a spacer for the DSC. The fabricated DSC with the flexible membrane CE showed higher photocurrent density than the conventional sandwich devices based on chemically deposited Pt/FTO glass, achieving a photovoltaic conversion efficiency of 4.43%. The results provides useful information in investigation and development of stable, low-cost, simple-design, flexible and lightweight DSCs.展开更多
Discharging wastewater containing heavy metals of Cu, Pb, Zn and Cd into water bodies can cause toxicity in plants and aquatic animals and some of them will be unable to survive except algae. Wastewater treatment meth...Discharging wastewater containing heavy metals of Cu, Pb, Zn and Cd into water bodies can cause toxicity in plants and aquatic animals and some of them will be unable to survive except algae. Wastewater treatment method to remove heavy metal contaminants includes chemical precipitation, ion exchange, membrane, filtration, adsorption using activated carbon. However, these methods are either expensive or have other disadvantages such as high energy consumption and inefficiencies when existing heavy metals are at trace concentration. Biosorption using algae biomass can be an alternative method to eliminate heavy metals. The objective of the project is to investigate the capability of Marine Algae (MA) and Freshwater Algae (FA) bi-omass in adsorbing heavy metals of Cu, Pb, Zn and Cd from water medium using synthetic water and industrial water. MA and FA were obtained from the eastern coast of Pulau Ubin and local fish farm respectively. After being fully washed with deionised water, dried in a furnace for 105°C, they are grinded to pass 1 mm2 of siever. MA and FA were characterised using FTIR to determine their functional groups. An industrial water was collected from industrial discharge from metal fac-tories in northern side of Singapore. Effect of adsorption time, adsorbent concentra-tion, and pH were studied. The result showed that FA and MA had a higher capability in adsorbing a total metal of about 40 ppm level from an industrial water, or 4 times than synthetic water concentration, at the same adsorbent dosage of 50 mg. In con-clusion, the presence of various functional groups, hydroxyl, carboxylic and amine groups, in all MA and FA samples had enabled the algae biomass to adsorb heavy metals of Cu, Pb, Cd and Zn from synthetic and industrial water. Due to their bio-sorptive properties and fast adsorption capability, algae could be a potential method for cleaning up surface water or post-treatment of wastewater and minimise the cost of eutrophication.展开更多
We explore a simple and eco-friendly approach for preparing CZTS powders and a screen-printing process for Cu_2ZnSn(S,Se)_4(CZTSSe) counter electrodes(CEs) in dye-sensitized solar cells(DSCs). Cu_2ZnSnS_4(CZTS) nanopa...We explore a simple and eco-friendly approach for preparing CZTS powders and a screen-printing process for Cu_2ZnSn(S,Se)_4(CZTSSe) counter electrodes(CEs) in dye-sensitized solar cells(DSCs). Cu_2ZnSnS_4(CZTS) nanoparticles have been synthesized via a hydrazine-free solvothermal approach without the assistance of organic ligands. CZTS has been prepared by directly drop-casting the CZTS ink on the cleaned FTO glass, while CZTSSe CEs have been fabricated by screen-printing CZTS pastes, followed by post selenization using Se vapor obtained from elemental Se pellets. The crystal structure, composition and morphology of the as-deposited CZTS nanoparticles and CZTSSe electrodes are characterized by X-ray diffractometer, energy dispersive spectrometer, field emission scanning electron microscopy and transmission electron microscopy.The electrochemical properties of CZTS, CZTSSe and Pt CE based DSCs are examined and analyzed by electrochemical impedance spectroscopy. The prepared CZTS and CZTSSe CEs exhibit a cellular structure with high porosity. DSCs fabricated with CZTSSe CEs achieve a power conversion efficiency of 5.75% under AM 1.5 G illumination with an intensity of 100 m W/cm^2, which is higher than that(3.22%) of the cell using the CZTS CE. The results demonstrate that the CZTSSe CE possesses good electrocatalytic activity for the reduction of charge carriers in electrolyte. The comprehensive CZTSSe CE process is cheap and scalable. It can make large-scale electro-catalytic film fabrication cost competitive for both energy harvesting and storage applications.展开更多
Methylene Blue (MB) has been found to be one of the most common dyes used in the industries. Adsorption process using Activated Carbon (AC) has been proven to be able to remove MB effectively but the treatment cost us...Methylene Blue (MB) has been found to be one of the most common dyes used in the industries. Adsorption process using Activated Carbon (AC) has been proven to be able to remove MB effectively but the treatment cost using the adsorbent is considered expensive due to its high energy cost. Sugarcane Bagasse (SGB) is an agricultural by-product and abundantly available material in many developing countries. FTIR and XRD were used to confirm the existence of ligno-cellulose content of SGB after experiencing various chemical treatments. SGB had 5 - 40 folds higher MB removal capability than commercial activated carbon, depending on the pH of water medium and the type of SGB. SGB showed a much better performance in adsorbing MB in alkaline environment than in acidic environment. Langmuir adsorption isotherm model was able to estimate the removal capacity of non-chemical treated SGB (NSGB) and CaCl2 treated SGB (CSGB) at 84.7458 mg/g and 35.2113 mg/g respectively. An extremely higher MB removal capacity was found for BSGB due to the complexity of the surface site after chemical treatment. NaOH treated SGB (BSGB) with low lignin residue content was the most favourable adsorbent for MB adsorption.展开更多
文摘Silica aerogels are light weight, nanostructured, and highly porous materials with an open pore structure. Due to their excellent characteristics, such as extremely low thermal conductivity, low density and high porosity, the silica aerogels become promising potential adsorbents, catalysts, thermal insulation, and acoustic absorption materials for environmental purposes. This paper presents the synthesis of a highly flexible polymer modified silica aerogel with the use of a cellulose-methyltriethoxysilane (MTES) precursor in a two-step acid-base catalyzed sol-gel process. The physical properties of the resulting aerogels were characterized by thermogravimetry, scanning electron microscopy, nitrogen adsorption-desorption, contact angle, thermal conductivity measurements, compression testing and Fourier transform infrared spectroscopy. The fabricated aerogel exhibited high flexibility with a Young’s modulus of compression of 0.33 MPa and the density of 0.132 g/cm3. They were hydrophobic in nature and had low thermal conductivity. Preparation of aerogel with solid waste (fly ash/bottom ash) is also discussed. The preliminary results showed that the materials have great potential for environmental application, i.e. enhancement of solid waste recycling rate by converting waste to high value-added materials, super thermal and acoustic insulation materials in green building and removal of oil spilled into surface drainage.
基金This work performed by the author was financially sup-ported by Singapore Ministry of Education innovation Fund(MOE2010-IF-027).
文摘Micro arc oxidation(MAO)coatings were formed on magnesium alloy AZ31B to improve the corrosion resistance using environmental friendly electrolyte solution under single-polar pulse power supply.The effect of electrical parameters of pulse frequency on the coating performance was studied at frequencies of 2.5 Hz,25 Hz and 250 Hz.The coating performance at different frequencies was characterized by scanning electron microscopy(SEM),energy-dispersive X-ray spectroscopy(EDS)and potentiodynamic polarization testing method.It was found that the corrosion resistance of the MAO coatings was improved when increasing the pulse frequencies from 2.5 Hz to 250 Hz.The corrosion current in 250 Hz case decreased by three orders of magnitude as compared with bare Mg alloy and the corrosion impedance also increased remarkably,means significantly enhanced corrosion resistance than bare Mg alloy.The results give us more insight in the optimization of electrical parameters to improve the MAO coating performance.The MAO technology is attractive for application on magnesium and other light alloys for surface protection in automotive and space industries.
基金supported by National Natural Science Foundation of China(No.10774046)Shanghai Municipal Science&Technology Committee(No.09JC1404600+1 种基金No.0852nm06100 and No.08230705400)Singapore Ministry of Education innovation fund(MOE IF Funding MOE2008-IF-1-016)
文摘A flexible counter electrode(CE) for dye-sensitized solar cells(DSCs) has been fabricated using a micro-porous polyvinylidene fluoride membrane as support media and sputtered Pt as the catalytic material.Non-conventional structure DSCs have been developed by the fabricated CEs. The Pt metal was sputtered onto one surface of the membrane as the catalytic material. DSCs were assembled by attaching the Ti O2 electrode to the membrane surface without Pt coating. The membrane was with cylindrical pore geometry. It served not only as a substrate for the CE but also as a spacer for the DSC. The fabricated DSC with the flexible membrane CE showed higher photocurrent density than the conventional sandwich devices based on chemically deposited Pt/FTO glass, achieving a photovoltaic conversion efficiency of 4.43%. The results provides useful information in investigation and development of stable, low-cost, simple-design, flexible and lightweight DSCs.
文摘Discharging wastewater containing heavy metals of Cu, Pb, Zn and Cd into water bodies can cause toxicity in plants and aquatic animals and some of them will be unable to survive except algae. Wastewater treatment method to remove heavy metal contaminants includes chemical precipitation, ion exchange, membrane, filtration, adsorption using activated carbon. However, these methods are either expensive or have other disadvantages such as high energy consumption and inefficiencies when existing heavy metals are at trace concentration. Biosorption using algae biomass can be an alternative method to eliminate heavy metals. The objective of the project is to investigate the capability of Marine Algae (MA) and Freshwater Algae (FA) bi-omass in adsorbing heavy metals of Cu, Pb, Zn and Cd from water medium using synthetic water and industrial water. MA and FA were obtained from the eastern coast of Pulau Ubin and local fish farm respectively. After being fully washed with deionised water, dried in a furnace for 105°C, they are grinded to pass 1 mm2 of siever. MA and FA were characterised using FTIR to determine their functional groups. An industrial water was collected from industrial discharge from metal fac-tories in northern side of Singapore. Effect of adsorption time, adsorbent concentra-tion, and pH were studied. The result showed that FA and MA had a higher capability in adsorbing a total metal of about 40 ppm level from an industrial water, or 4 times than synthetic water concentration, at the same adsorbent dosage of 50 mg. In con-clusion, the presence of various functional groups, hydroxyl, carboxylic and amine groups, in all MA and FA samples had enabled the algae biomass to adsorb heavy metals of Cu, Pb, Cd and Zn from synthetic and industrial water. Due to their bio-sorptive properties and fast adsorption capability, algae could be a potential method for cleaning up surface water or post-treatment of wastewater and minimise the cost of eutrophication.
基金supported by National Natural Science Foundation of China (No. 11274119 and 61275038)Pujiang Talent Program of Shanghai Science and Technology Commission (No. 11PJ1402700)
文摘We explore a simple and eco-friendly approach for preparing CZTS powders and a screen-printing process for Cu_2ZnSn(S,Se)_4(CZTSSe) counter electrodes(CEs) in dye-sensitized solar cells(DSCs). Cu_2ZnSnS_4(CZTS) nanoparticles have been synthesized via a hydrazine-free solvothermal approach without the assistance of organic ligands. CZTS has been prepared by directly drop-casting the CZTS ink on the cleaned FTO glass, while CZTSSe CEs have been fabricated by screen-printing CZTS pastes, followed by post selenization using Se vapor obtained from elemental Se pellets. The crystal structure, composition and morphology of the as-deposited CZTS nanoparticles and CZTSSe electrodes are characterized by X-ray diffractometer, energy dispersive spectrometer, field emission scanning electron microscopy and transmission electron microscopy.The electrochemical properties of CZTS, CZTSSe and Pt CE based DSCs are examined and analyzed by electrochemical impedance spectroscopy. The prepared CZTS and CZTSSe CEs exhibit a cellular structure with high porosity. DSCs fabricated with CZTSSe CEs achieve a power conversion efficiency of 5.75% under AM 1.5 G illumination with an intensity of 100 m W/cm^2, which is higher than that(3.22%) of the cell using the CZTS CE. The results demonstrate that the CZTSSe CE possesses good electrocatalytic activity for the reduction of charge carriers in electrolyte. The comprehensive CZTSSe CE process is cheap and scalable. It can make large-scale electro-catalytic film fabrication cost competitive for both energy harvesting and storage applications.
文摘Methylene Blue (MB) has been found to be one of the most common dyes used in the industries. Adsorption process using Activated Carbon (AC) has been proven to be able to remove MB effectively but the treatment cost using the adsorbent is considered expensive due to its high energy cost. Sugarcane Bagasse (SGB) is an agricultural by-product and abundantly available material in many developing countries. FTIR and XRD were used to confirm the existence of ligno-cellulose content of SGB after experiencing various chemical treatments. SGB had 5 - 40 folds higher MB removal capability than commercial activated carbon, depending on the pH of water medium and the type of SGB. SGB showed a much better performance in adsorbing MB in alkaline environment than in acidic environment. Langmuir adsorption isotherm model was able to estimate the removal capacity of non-chemical treated SGB (NSGB) and CaCl2 treated SGB (CSGB) at 84.7458 mg/g and 35.2113 mg/g respectively. An extremely higher MB removal capacity was found for BSGB due to the complexity of the surface site after chemical treatment. NaOH treated SGB (BSGB) with low lignin residue content was the most favourable adsorbent for MB adsorption.