Hot cracking during solidification can be a serious problem in aluminium casting alloys under certain conditions.This feature is well known,but still insuffi ciently investigated in shape casting.This study gives a br...Hot cracking during solidification can be a serious problem in aluminium casting alloys under certain conditions.This feature is well known,but still insuffi ciently investigated in shape casting.This study gives a brief overview of the factors inf luencing hot cracking during shape casting.Five different AlSi7MgCu alloys with varying Mg and Cu contents were examined.Theoretical models,including the cracking susceptibility coeffi cient(CSC)from Clyne and Davies,were considered.Thermodynamic calculations(terminal freezing range,TFR)of the behavior of the solid fraction during solidif ication were compared to an experimentbased hot cracking indexing(HCI)method.Scanning electron microscopy(SEM)was used to compare the existing microstructure and precipitated thermodynamic phases using the software ThermoCalc Classic(TCC).Furthermore,SEM was used to investigate crack surfaces initiated by a dog-bone shaped mold during casting.A good correlation between theoretical models and the experimental hot cracking index method was observed.展开更多
Three types of near-net shape casting alumi- num parts were investigated by computed tomography to determine casting defects and evaluate quality. The first, second, and third parts were produced by low-pressure die c...Three types of near-net shape casting alumi- num parts were investigated by computed tomography to determine casting defects and evaluate quality. The first, second, and third parts were produced by low-pressure die casting （Al-12Si-0.8Cu-0.5Fe-0.9Mg-0.7Ni-0.2Zn alloy）, die casting （A356, A1-7Si-0.3Mg）, and semi-solid casting （A356, A1-TSi-0.3Mg）, respectively. Unlike die casting （second part）, low-pressure die casting （first part） sig- nificantly reduced the formation of casting defects （i.e., porosity） due to its smooth filling and solidification under pressure. No significant casting defect was observed in the third part, and this absence of defects indicates that semi- solid casting could produce high-quality near-net shape casting aluminum parts. Moreover, casting defects were mostly distributed along the eutectic grain boundaries. This finding reveals that refinement of eutectic grains is necessary to optimize the distribution of casting defects and reduce their size. This investigation demonstrated that computed tomography is an efficient method to determine casting defects in near-net shape casting aluminum parts.展开更多
基金financially supported by the Austrian Research Promotion Agency FFG
文摘Hot cracking during solidification can be a serious problem in aluminium casting alloys under certain conditions.This feature is well known,but still insuffi ciently investigated in shape casting.This study gives a brief overview of the factors inf luencing hot cracking during shape casting.Five different AlSi7MgCu alloys with varying Mg and Cu contents were examined.Theoretical models,including the cracking susceptibility coeffi cient(CSC)from Clyne and Davies,were considered.Thermodynamic calculations(terminal freezing range,TFR)of the behavior of the solid fraction during solidif ication were compared to an experimentbased hot cracking indexing(HCI)method.Scanning electron microscopy(SEM)was used to compare the existing microstructure and precipitated thermodynamic phases using the software ThermoCalc Classic(TCC).Furthermore,SEM was used to investigate crack surfaces initiated by a dog-bone shaped mold during casting.A good correlation between theoretical models and the experimental hot cracking index method was observed.
文摘Three types of near-net shape casting alumi- num parts were investigated by computed tomography to determine casting defects and evaluate quality. The first, second, and third parts were produced by low-pressure die casting （Al-12Si-0.8Cu-0.5Fe-0.9Mg-0.7Ni-0.2Zn alloy）, die casting （A356, A1-7Si-0.3Mg）, and semi-solid casting （A356, A1-TSi-0.3Mg）, respectively. Unlike die casting （second part）, low-pressure die casting （first part） sig- nificantly reduced the formation of casting defects （i.e., porosity） due to its smooth filling and solidification under pressure. No significant casting defect was observed in the third part, and this absence of defects indicates that semi- solid casting could produce high-quality near-net shape casting aluminum parts. Moreover, casting defects were mostly distributed along the eutectic grain boundaries. This finding reveals that refinement of eutectic grains is necessary to optimize the distribution of casting defects and reduce their size. This investigation demonstrated that computed tomography is an efficient method to determine casting defects in near-net shape casting aluminum parts.
