Roller Profile Online Measurement Based on Ultrasonic Circulation Pulse-echo Technology

In order to meet the high precision requirement of wide steel strip in industry field, a novel online measurement of roller profile based on sonic circulation and pulse-echo technology was introduced. All kinds of the factors influencing the accuracy of roller profile online measurement were analyzed in detail and error compensation analysis of system was accordingly presented. In order to reduce count error, field program gate array(FPGA) was introduced and a highprecision data acquisition system was designed based on digital phase-shift technology. Experiments indicate that the standard deviation of measure data was 7.27 μm, which showed the feasibility and validity of the proposed method, and realized the roll profile measurement with high precision.

Detection Techniques of Femtosecond Lasers

The measurement techniques of femtosecond spectroscopy are effective method to investigate ultrafast dynamics, they are widely used in the fields of physics, chemistry and biology. In this paper, the principle, experiment setup and the approaches to deal with the experiment data were presented. Then different measurement techniques such as transient absorption spectroscopy, photon echoes, optical Kerr effect and degenerate four-wave mixing were explained with special examples. At last, the application prospect of measurement techniques of femtosecond spectroscopy was forecasted.

Multiplexing Technique Applied in the Optically Powered Oil-tank Detection System

The method of using multiplexing technique to realize the optically powered multiple detection system is presented. As this system adopted novel time and pulse width multiplexing techniques, reliable separation and error code correcting techniques, it realizes optically powered multiple channel and parameters detection, and successfully applied in the oil tanks for temperature, pressure, liquid level and reserve measurings.

Silicon Deep Etching Techniques for MEMS Devices

Silicon deep etching technique is the key fabrication step in the development of MEMS. The mask selectivity and the lateral etching control are the two primary factors that decide the result of deep etching process. These two factors are studied in this paper. The experimental results show that the higher selectivity can be gotten when F - gas is used as etching gas and Al is introduced as mask layer. The lateral etching problems can be solved by adjusting the etching condition, such as increasing the RF power, changing the gas composition and flow volume of etching machine.

Research on Electric Field Confinement Effect in Silicon LED Fabricated by Standard CMOS Technology

The wedge-shaped and leaf-type silicon light-emitting devices(LED)are designed and fabricated with the Singapore Chartered Semi Inc.'s dual-gate standard 0.35μm CMOS process.The basic structure of the two devices is N well-P+ junction.P+ area is the wedge-shaped structure,which is embedded in N well.The leaf-type silicon LED device is a combination of the three wedge-shaped LED devices.The main difference between the two devices is their different electrode distribution,which is mainly in order to analyze the application of electric field confinement(EFC).The devices' micrographs were measured with the Olympus IC test microscope.The forward and reverse bias electrical characteristics of the devices were tested.Light measurements of the devices show that the electrode layout is very important when the electric field confinement is applied.

Parallel Image Processing Technology of Surface Detection System

To improve image processing speed and detection precision of a surface detection system on a strip surface,based on the analysis of the characteristics of image data and image processing in detection system on the strip surface,the design of parallel image processing system and the methods of algorithm implementation have been studied. By using field programmable gate array(FPGA) as hardware platform of implementation and considering the characteristic of detection system on the strip surface,a parallel image processing system implemented by using multi IP kernel is designed. According to different computing tasks and the load balancing capability of parallel processing system,the system could set different calculating numbers of nodes to meet the system's demand and save the hardware cost.

Signal Processing for Fibre-optic Distributed Sensing Techniques Employing Brillouin Scattering

As fibre optic distributed scattering sensing systems are providing innovative solutions for the monitoring of large structures,Brillouin-based distributed scattering sensing techniques represent a new physical approach for structures health monitoring,which seems extremely promising and is receiving most attentions.This paper comprehensively presents some methods of signal interrogation for fibre optic Brillouin-based distributed scattering sensing technology,especially establishes an accurate Pseudo-Voigt model of Brillouin gain spectrum and gives some results on spectrum analysis and data processing.

Optical Measurement System for Motion Characterization of Surface Mount Technology

Advanced testing methods for the dynamics of mechanical microdevices are necessary to develop reliable, marketable microelectromechanical systems. A system for measuring the nanometer motions of microscopic structures has been demonstrated. Stop-action images of a target have been obtained with computer microvision, microscopic interferometry, and stroboscopic illuminator. It can be developed for measuring the in-plane-rigid-body motions, surface shapes, out-of-plane motions and deformations of microstructures. A new algorithm of sub-pixel step length correlation template matching is proposed to extract the in-plane displacement from vision images. Hariharan five-step phase-shift interferometry algorithm and unwrapping algorithms are adopted to measure the out-of-plane motions. It is demonstrated that the system can measure the motions of solder wetting in surface mount technology(SMT).

Application of Spatial Filtering Techniques in the Measurement of the Velocity

As one of the interesting optical techniques for measurements of the velocity,the spatial filtering method is treated briefly in this paper.We shown theoretical analysis and calculation of spatial filtering velocimetry,and discussed two-dimensional measurements of the velocity.About the data processing,we used A/D conversion and interfaced with a microcomputer,so that the data can be processed automatically by the microcomputer.The preliminary experiment was performed and the experimental results show the usefulness of the present method for measurements of the velocity.

Subpixel Target Location Techniques for 3-D Coordinate Measuring System

the close photogrammetric 3-D coordinate measurement is a newmeasuring technology in the fields of the coordinate measurementmachine (CMM) in recent years. In this method, we usually place sometargets on the measured object and take image of targets to determinethe object coordinate. The subpixel location of target image plays animportant role in high accuracy 3-D coordinate measuring procedure.In this paper, some subpixel location methods are reviewed and somefactors which affect location precision are analyzed.

An Electrochemical Cleaning Technique for Removal of Surface Contamination before Texturization of Silicon Solar Cells

In order to decrease the consumption of reagents and silicon during removal of surface contamination before silicon texturing in solar cell manufacturing industry, a new low-cost surface treatment approach of electrochemical cleaning technique(ECT) is reported. In this technique, a powerful oxidizing electrolyte was obtained from the electrochemical reaction on Boron-doped Diamond(BDD) electrodes, and applied during removal of surface contaminations on silicon wafer surfaces. The slightly polished monocrystalline silicon surfaces after cleaning were compared with the ones of primal silicon wafers. The measurement results show that ECT is quite efficient in removing NaCl and organic contaminants. After cleaning, the contrast test was conducted for the textured silicon wafers with/without pre-treatment(polish) separately. The results show that the size of pyramids on the surface without traditional polishing process is homogeneous and smaller than 4μm, and the average surface reflectance is much lower in the wavelength range from 400nm to 800nm. Therefore, the new technique can save silicon material, and effectively avoid optical losses for improving photoconversion effect of solar cells.

Technology of Laser Protection and Defrosting Film

A compound coating of electrically conductive and visible transparent film and laser protective film has been developed,this coating has light densities of no less than 4 against 0.53 μm and no less than 3 against 1.06 μm in the range of ±30° angular field.The average transmittance value as high as 60% from 0.4 μm to 0.7 μm has been achieved.The structures of the laser protective filters are compared.The refractive index of a compound material used in the matching layer has been given.Measured results of the laser protective film coating are compared with that of the compound coating.

Novel Tunable PMD Compensation Technology Using Linear Chirped Fiber Bragg Grating

Based on uniform fiber Bragg grating bonded with a magnetostrictive rod in the non-uniform magnetic field,a novel PMD compensation technique is proposed.This all-fiber PMD compensation technology is cost-effective and flexible in designing the differential group delay profile.

Synthesized Structure of Amplitude-sampled FBG by Simple Inverse FT Technology and Its Application

Using the simple inverse Fourier transformation(FT), the index modulation structure with the sampled period for the sampled fiber Bragg gratings was designed. In this method, the enable channels are operated at identical wavelength while the unable channels are almost suppressed completely. The enable and unable channels can be established based on the applications. This technique is very useful to design the optical devices such as optical add and drop multiplexers (OADMs), and interleavers with dispersion and dispersion slope compensation.

Research on Vehicle Anti-collision Technique Based on Monocular Vision

Vehicle anti-collision technique is a hot topic in the research area of Intelligent Transport System. The research on preceding vehicles detection and the distance measurement, which are the key techniques, makes great contributions to safe-driving. This paper presents a method which can be used to detect preceding vehicles and get the distance between own car and the car ahead. Firstly, an adaptive threshold method is used to get shadow feature, and a shadow!area merging approach is used to deal with the distortion of the shadow border. Region of interest(ROI) is obtained using shadow feature. Then in the ROI, symmetry feature is analyzed to verify whether there are vehicles and to locate the vehicles. Finally, using monocular vision distance measurement based on camera interior parameters and geometrical reasoning, we get the distance between own car and the preceding one. Experimental results show that the proposed method can detect the preceding vehicle effectively and get the distance between vehicles accurately.

Design of Low-power Inspection Instrument Based on RF Technology

A design for low power consumption inspection instrument, in which the ATMega32L is used as the control core, is presented. The reader with wireless identification based on RF technology is researched and the low-cost power is studied particularly. This instrument can be used in industry fields to measure temperature, humidity, gas concentration and other specifications, so it has wide applications and is worth to be extended.

Implementation of Synchronization Technology in Orthogonal Frequency Division Multiplex System Based on Field Programming Gate Array

In this paper,analyzed is the symbol synchronization algorithm in orthogonal frequency division multiplex(OFDM)system,and accomplished are the hardware circuit design of coarse and elaborate synchronization algorithms.Based on the analysis of coarse and elaborate synchronization algorithms,multiplexed are,the module accumulator,division and output judgement,which can evidently save the hardware resource cost.The analysis of circuit sequence and wave form simulation of the design scheme shows that the proposed method efficiently reduce system resources and power consumption.

Dispersion Monitoring Techniques in High Bit-rate Optical Communication Systems

For the efficient dynamic dispersion compensation, it is essential to monitor the dispersion accurately. The existing main dispersion monitoring techniques in high bit-rate optical communication systems are presented as well as their operating principles and research progress. The advantages and disadvantages of these methods are analyzed and discussed.

Ruby (Al_2O_3∶Cr^(3+)) Fluorescence Thermometer Using PLD-PMSR Technique

A kind of fluorescence fiber-optic thermometer is devised based on the solid-state ruby fluorescence material. The characteristics of fluorescence material absorption and emission are analyzed, and the fiber-optic temperature measurement probe in ruby is developed. This system is particularly adaptable to the temperature measurement in the range of 20℃ to 600℃. During the experiment, this method is proved to be useful to temperature measurement with high resolution and precision.

SEM and Positron Annihilation Technology Investigation on the Defect Change with Thermal Treatment Temperature in GaP

Defects in S doped GaP single crystal which is prepared by LEC method were observed using SEM and positron lifetime,and its change with thermal treatment temperature was measured using positron annihilation spectrometer.The relationship between positron lifetime and the combination state of defects was discussed.