Application of Al-free deoxidizer in rail steel manufacture

Because there are a lot of influences of alumina inclusions on the performance of rail steel,it is reasonable to adopt the deoxidization method with Al-free deoxidizer. According to the characteristics of Al-free deoxidization process,the control of aluminum content,the deoxidization with ladle furnace（LF） slag,the deoxidization process under vacuum by carbon,and the inclusions modification technology by calcium treatment were studied. All of them were applied to practical production. The results indicate that the adoption of Al-free deoxidization process leads to the total oxygen content in the steel below 20 ppm,which meets the requirement of clean rail steel.

Effect of Multiple Forging on Microstructure and Mechanical Properties of Powder Metallurgy FGH4096 Superalloy

FGH4096 is an important damage-tolerance-type powder metallurgy （PM） superalloy, which is also the optimized turbine material for high performance aero-engine. To turbine disc, bore and rim are used in high temperature-low stress condition and low temperature-high stress condition, and dual-microstructure is introduced. Coarse-grained microstructure is suit for rim region and fine-grained is no doubt most suitable for bore region. But fine-grained ingot can not make by PM technique, so that gradient heat treatment can not be developed to coarsen the grain of rim region. Under the confine of PM technique, several treatment processir, g should be taken place to refine the coarse grains of PM alloy. Multiple forging with large accumulate deformation was carried cat on PM FGH4096 superalloy, and fine grains of 3.5 μm were obtained by this treatment processing. Mechanical properties testing were ake carried out on both fine-grained and other statuses alloys, Microstrucmre evolution was observed by optical microscopy, scanning electron microscopy and transmission electron microscopy. As a result of repeated dynamic recrystallizafion, coarse grains could be completely refined into fine grains. And the increase of strength was mainly attributed to refinement effect and improvement of defects such as previous particle boundaries. Successful development of fine-grained treatment processing will promote the research of dual-microstructure turbine disc.

NUMERICAL SIMULATION OF TEMPERATURE FIELDS IN ELECTROSLAG REMELTING SLAB INGOTS

The method based on transient heat transfer model is adopted to simulate electro-slag remelting process. The calculated results of the model show that the process is in the quasi-steady state, and the shape of pool remains unchanged when the height of ingot is approximately 2.5-3 times the thickness of slab ingot. The change in the shape of pool is found to be strongly dependent on the pattern of melting rate, and hence, the power input; the depth of the molten pool increases with the increase in melting speed. It is concluded that a transient heat transfer model has to be used to obtain reliable input information for the entire, operatina time.

Effect of solid-solution temperature on the microstructure of Fe-Ni based high strength low thermal expansion (HSLTE) alloy

The influence of solid-solution temperature on the dissolution of carbide precipitates, the average grain size and the microhardness of the austenite matrix in an Fe-Ni based high strength low thermal expansion （HSLTE） alloy was investigated to obtain the proper temperature range of the solid-solution process. The XRD analysis, microstructure observations, and the theoretical calculations showed that the Mo-rich M2C-type precipitates in the Fe-Ni based HSLTE alloy dissolve completely at about 1100℃. The average grain size of the studied alloys increases from 14 to 46 μm in the temperature range of 1050 to 1200℃. The microhardness of the matrix decreases gust for the sake of solid-solution treatment, but then increases later with increasing solution temperature because of the solution strengthening effect.

Hot deformation behavior of FGH96 superalloys

The hot deformation behavior of FGH96 superalloys at 1070-1170℃ and 5×10^-4-2×10^-1 s^-1 were investigated by means of the isothermal compression tests at a Gleeble-1500 thermal mechanical simulator. The results show that dynamic recovery acts as the main softening mechanism below 2×10^-3 s^-1, whereas dynamic recrystallization acts as the main softening mechanism above 2× 10^-3 s^-1 during deformation; the temperature increase caused by the deformation and the corresponding softening stress is negligible; the thermal-mechanical constitutive model to describe the hot deformation behavior is given, and the value of the apparent deformation activation energy （Qdef） is determined to be 354.93 kJ/mol.

Roles of Te and Mn in the two phases of manganite with nominal composition La_(0.6)Sr_(0.1)Te_xMnO_3

Powder samples with nominal composition La0.6Sr0.1TexMnO3 （x = 0.00, 0.05, 0.10, 0.15, 0.20） were prepared using the sol-gel method with thermal treatment up to 1473 K. On the basis of powder X-ray diffraction （XRD）, thermogravimetric and magnetic measurements, it was found that almost all of the Te and a few of the Mn ions were lost from the samples when they were calcined at 1473 K. The reason for the Te loss and a quantitative phase analysis for the samples calcined at 1473 K are discussed in detail.

Temperature stability and microstructure of ultra-high intrinsic coercivity Nd-Fe-B magnets

The variations of intrinsic coercivity and remanence of sintered Nd-Fe-B magnets with ultra-high intrinsic coercivity were investigated. The results showed that the intrinsic coercivity and remanence declined simultaneously with increasing temperature, but the squareness of the magnets has hardly been changed. The temperature coefficients of remanence （α） and coercivity （β） for the magnets were calculated by two different methods, and the variations of the temperature coefficients and the microstructure of sintered Nd-Fe-B magnets were analyzed. The temperature coefficients of remanence （α） and coercivity （β） for the sintered magnets are very small, and the existence of fine microstructure is necessary to obtain sintered Nd-Fe-B magnets with ultra-high intrinsic coercivity.

Desulfurizer desulphurization kinetics by the injection method

To obtain a better desulphurization effect in hot metal, suitable desulfurizers should be selected first according to thermodynamics. However, the effect of desulphurization is also strongly affected by kinetics. The conditions of different desulfurizers （Mg, CaC2, and lime） penetrating into hot metal, the rising up velocity in iron melt, residence time, and dissolving time are theoretically calculated and analyzed. The results are helpful to select the desulphurization process and equipment and to improve the desulphurization effect.

METAL INERT GAS WELDING OF 2519-T87 HIGH STRENGTH ALUMINUM ALLOY

20 mm thick plates of 2519-T87 high strength aluminum alloy have been welded.The effects of the compositions of filler wires,the heat input and the compositions of shielding gas on the mechanical properties and microstructure of the welded joint have been investigated.The results indicate that finer microstructure,better mechanical properties and higher value of hardness of HAZ can be obtained by using lower heat input.The use of Ar/He mixed shielding gas has several advantages over pure Ar shielding gas.With the increase of the proportion of He in the mixed shielding gas, the grain size of the weld metal as well as porosity susceptibility decreases.When the volume ratio of He to Ar reaches 7：3,the porosity and the grain size of weld metal reach the minimum,and the porosity can be further reduced by filling some CO2.