Due to the complex structure and dense weld of the orthotropic steel bridge deck(OSBD),fatigue cracks are prone to occur in the typical welding details.Welding residual stress(WRS)will cause a plastic zone at the crac...Due to the complex structure and dense weld of the orthotropic steel bridge deck(OSBD),fatigue cracks are prone to occur in the typical welding details.Welding residual stress(WRS)will cause a plastic zone at the crack tip.In this paper,an elastoplastic constitutive model based on the Chaboche kinematic hardening model was introduced,and the extended finite element method(XFEM)was used to study the influence of material elastoplasticity and crack tip plastic zone on the law of fatigue crack propagation.By judging the stress state of the residual stress field at the crack tip and selecting different crack propagation rate models to investigate the crack propagation law when plastic deformation was considered,the propagation path and propagation rate of fatigue crack of the OSBD were obtained.The results show that,whether the residual stress field is considered or not,the plastic deformation at the crack tip will not cause the obvious closure of the fatigue crack at the U-rib toe during the crack propagation process,but will significantly affect the crack propagation path.When material plasticity is considered,the propagation angle of fatigue crack at the U-rib toe basically remains unchanged along the short-axis direction of the initial crack,but is going up along the long-axis direction,and the crack tip plastic zone inhibits the propagation of the crack tip on one side.Compared with linear elastic materials,the crack propagation law considering material plasticity is more consistent with that in actual bridge engineering.In terms of the propagation rate,if the residual stress field is not considered,the fatigue crack propagation rate at U-rib toe with plasticity considered is slightly higher than that without plasticity considered,because plastic deformation will affect the amplitude of energy release rate.When considering the WRS field,the fatigue crack propagation rate at U-rib toe is increased due to the combined actions of plastic deformation and stress ratio R.展开更多
Aerodynamic instability owing to aerostatic and flutter-related failures is a significant concern in the wind-resistant design of long-span suspension bridges.Based on the dynamic characteristics of suspension bridges...Aerodynamic instability owing to aerostatic and flutter-related failures is a significant concern in the wind-resistant design of long-span suspension bridges.Based on the dynamic characteristics of suspension bridges with spans ranging from 888 to 1991 m,we proposed fitted equations for increasing spans and base frequencies.Finite element models of suspension bridges with increasing span from 1000 to 5000 m were constructed.The structural parameters were optimized to follow the fitted tendencies.To analyze the aerodynamic instability,streamlined single-box section(SBS),lattice truss section(LTS),narrow slotted section(NSS),and wide slotted section(WSS)were considered.We performed three-dimensional(3-D)full-mode flutter analysis and nonlinear aerostatic instability analysis.The flutter critical wind speed continuously decreases with span growth,showing an unlimited approaching phenomenon.Regarding aerostatic instability,the instability wind speed decreases with span to approximately 3000 m,and increases when the span is in the range of 3000 to 5000 m.Minimum aerostatic instability wind speed with SBS or LTS girder would be lower than observed maximal gust wind speed,indicating the probability of aerostatic instability.This study proposes that suspension bridge with span approximately 3000 m should be focused on both aerostatic instability and flutter,and more aerodynamic configuration optimistic optimizations for flutter are essential for super long-span suspension bridges with spans longer than 3000 m.展开更多
基金The works described in this paper are substantially supported by the grant from the National Natural Science Foundation of China(Grant No.51678135)the Natural Science Foundation of Jiangsu Province(No.BK20171350)Six Talent Peak Projects in Jiangsu Province(JNHB-007),which are gratefully acknowledged.
文摘Due to the complex structure and dense weld of the orthotropic steel bridge deck(OSBD),fatigue cracks are prone to occur in the typical welding details.Welding residual stress(WRS)will cause a plastic zone at the crack tip.In this paper,an elastoplastic constitutive model based on the Chaboche kinematic hardening model was introduced,and the extended finite element method(XFEM)was used to study the influence of material elastoplasticity and crack tip plastic zone on the law of fatigue crack propagation.By judging the stress state of the residual stress field at the crack tip and selecting different crack propagation rate models to investigate the crack propagation law when plastic deformation was considered,the propagation path and propagation rate of fatigue crack of the OSBD were obtained.The results show that,whether the residual stress field is considered or not,the plastic deformation at the crack tip will not cause the obvious closure of the fatigue crack at the U-rib toe during the crack propagation process,but will significantly affect the crack propagation path.When material plasticity is considered,the propagation angle of fatigue crack at the U-rib toe basically remains unchanged along the short-axis direction of the initial crack,but is going up along the long-axis direction,and the crack tip plastic zone inhibits the propagation of the crack tip on one side.Compared with linear elastic materials,the crack propagation law considering material plasticity is more consistent with that in actual bridge engineering.In terms of the propagation rate,if the residual stress field is not considered,the fatigue crack propagation rate at U-rib toe with plasticity considered is slightly higher than that without plasticity considered,because plastic deformation will affect the amplitude of energy release rate.When considering the WRS field,the fatigue crack propagation rate at U-rib toe is increased due to the combined actions of plastic deformation and stress ratio R.
基金support of National Key R&D Program of China(No.2022YFC3004105)National Natural Science Foundation of China(Grant Nos.52078383,52008314,52108469).
文摘Aerodynamic instability owing to aerostatic and flutter-related failures is a significant concern in the wind-resistant design of long-span suspension bridges.Based on the dynamic characteristics of suspension bridges with spans ranging from 888 to 1991 m,we proposed fitted equations for increasing spans and base frequencies.Finite element models of suspension bridges with increasing span from 1000 to 5000 m were constructed.The structural parameters were optimized to follow the fitted tendencies.To analyze the aerodynamic instability,streamlined single-box section(SBS),lattice truss section(LTS),narrow slotted section(NSS),and wide slotted section(WSS)were considered.We performed three-dimensional(3-D)full-mode flutter analysis and nonlinear aerostatic instability analysis.The flutter critical wind speed continuously decreases with span growth,showing an unlimited approaching phenomenon.Regarding aerostatic instability,the instability wind speed decreases with span to approximately 3000 m,and increases when the span is in the range of 3000 to 5000 m.Minimum aerostatic instability wind speed with SBS or LTS girder would be lower than observed maximal gust wind speed,indicating the probability of aerostatic instability.This study proposes that suspension bridge with span approximately 3000 m should be focused on both aerostatic instability and flutter,and more aerodynamic configuration optimistic optimizations for flutter are essential for super long-span suspension bridges with spans longer than 3000 m.