In order to improve the thermal properties of coke, an industrial experiment on the coke spraying with ZBS additive solution was carried out at coking plant and No. 6 blast furnace （2 000 m^3 ） of Kunming Iron and S...In order to improve the thermal properties of coke, an industrial experiment on the coke spraying with ZBS additive solution was carried out at coking plant and No. 6 blast furnace （2 000 m^3 ） of Kunming Iron and Steel Co Ltd. The coke reaction index （CRI） of the coke spraying with ZBS additive solution decreases by 10. 56 %, and the coke strength after reaction （CSR） increases by 7.80% in comparison with those of the un-sprayed coke. During the experiment, the average iron output increases by 66. 69 t/d, and the coke rate is reduced by 5. 21 kg per ton iron, while the fluctuation of furnace temperture is small, and sulphur content in hot metal and 100% of hot metal are acceptable.展开更多
The coke plant of a steel plant corresponds to the area that transforms a blend of coal into coke for using in blast furnace and steam to power plant. The coking plant of ThyssenKrupp CSA uses the heat recovery techno...The coke plant of a steel plant corresponds to the area that transforms a blend of coal into coke for using in blast furnace and steam to power plant. The coking plant of ThyssenKrupp CSA uses the heat recovery technology with stamping charger for stamping and preparation a blend of coals for charging and coking. Stamping technology adds several benefits to the process, such as increased density, homogeneity and alignment of the coal cake charged into the oven, as well as provides better control of the coking process, improves parameters of coke quality and allows coal blending with lower coking power, thereby reducing the production cost of coke and power generation. Through the automation of stamping charger, it is possible to evaluate and calculate the stamped coal density charged and the productivity gains this system provides.展开更多
The maximum possibility of utilizing the Indian coking coals and inferior grade coking coal for producing metallurgical coke through non-recovery stamp charging tech_nology was investigated. Indian indigenous coals co...The maximum possibility of utilizing the Indian coking coals and inferior grade coking coal for producing metallurgical coke through non-recovery stamp charging tech_nology was investigated. Indian indigenous coals contained low percent of vitrinite （〈50%） and higher content of ash （〉15%） compared to imported coking coal. Therefore, the selection of appropriate proportion of different types of coals was a major challenge for coke makers. Coal blend selection criterion based on a single coefficient, named as composite coking potential （CCP）, was developed. The use of increased proportion of semi-soft coal （crucible swelling number of 2.5） and high ash （≥15%） indigenous coal in the range of 20%- 35% and 20%-65% respectively in the blends resulted in good quality of coke. Plant data of a non recovery coke oven were used for developing and validating the model. The results showed that the coke strength after reaction （CSR） varied in the range of 63.7%-67.7% and the M40 value was between 81.8 and 89.3 in both the cases.展开更多
文摘In order to improve the thermal properties of coke, an industrial experiment on the coke spraying with ZBS additive solution was carried out at coking plant and No. 6 blast furnace （2 000 m^3 ） of Kunming Iron and Steel Co Ltd. The coke reaction index （CRI） of the coke spraying with ZBS additive solution decreases by 10. 56 %, and the coke strength after reaction （CSR） increases by 7.80% in comparison with those of the un-sprayed coke. During the experiment, the average iron output increases by 66. 69 t/d, and the coke rate is reduced by 5. 21 kg per ton iron, while the fluctuation of furnace temperture is small, and sulphur content in hot metal and 100% of hot metal are acceptable.
文摘The coke plant of a steel plant corresponds to the area that transforms a blend of coal into coke for using in blast furnace and steam to power plant. The coking plant of ThyssenKrupp CSA uses the heat recovery technology with stamping charger for stamping and preparation a blend of coals for charging and coking. Stamping technology adds several benefits to the process, such as increased density, homogeneity and alignment of the coal cake charged into the oven, as well as provides better control of the coking process, improves parameters of coke quality and allows coal blending with lower coking power, thereby reducing the production cost of coke and power generation. Through the automation of stamping charger, it is possible to evaluate and calculate the stamped coal density charged and the productivity gains this system provides.
文摘The maximum possibility of utilizing the Indian coking coals and inferior grade coking coal for producing metallurgical coke through non-recovery stamp charging tech_nology was investigated. Indian indigenous coals contained low percent of vitrinite （〈50%） and higher content of ash （〉15%） compared to imported coking coal. Therefore, the selection of appropriate proportion of different types of coals was a major challenge for coke makers. Coal blend selection criterion based on a single coefficient, named as composite coking potential （CCP）, was developed. The use of increased proportion of semi-soft coal （crucible swelling number of 2.5） and high ash （≥15%） indigenous coal in the range of 20%- 35% and 20%-65% respectively in the blends resulted in good quality of coke. Plant data of a non recovery coke oven were used for developing and validating the model. The results showed that the coke strength after reaction （CSR） varied in the range of 63.7%-67.7% and the M40 value was between 81.8 and 89.3 in both the cases.
