Wearable devices with efficient thermal management and electromagnetic interference(EMI) shielding are highly desirable for improving human comfort and safety. Herein, a multifunctional wearable carbon fibers(CF) @ po...Wearable devices with efficient thermal management and electromagnetic interference(EMI) shielding are highly desirable for improving human comfort and safety. Herein, a multifunctional wearable carbon fibers(CF) @ polyaniline(PANI)/silver nanowires(Ag NWs) composites with a “branch-trunk” interlocked micro/nanostructure were achieved through "three-in-one" multi-scale design. The reasonable assembly of the three kinds of one-dimensional(1D) materials can fully exert their excellent properties i.e., the superior flexibility of CF, the robustness of PANI, and the splendid conductivity of Ag NWs. Consequently, the constructed flexible composite demonstrates enhanced mechanical properties with a tensile stress of 1.2 MPa, which was almost 6 times that of the original material. This is mainly attributed to the fact that the PNAI(branch) was firmly attached to the CF(trunk) through polydopamine(PDA), forming a robust interlocked structure. Meanwhile, the composite possesses excellent thermal insulation and heat preservation capacity owing to the synergistically low thermal conductivity and emissivity. More importantly, the conductive path of the composite established by the three 1D materials greatly improved its EMI shielding property and Joule heating performance at low applied voltage. This work paves the way for rational utilization of the intrinsic properties of 1D materials, as well as provides a promising strategy for designing wearable electromagnetic protection and thermal energy management devices.展开更多
Ethyl cellulose(EC),an important biomass-based material,has excellent film-forming properties.Nevertheless,the high interchain hydrogen bond interaction leads to a high glass transition temperature of EC,which makes i...Ethyl cellulose(EC),an important biomass-based material,has excellent film-forming properties.Nevertheless,the high interchain hydrogen bond interaction leads to a high glass transition temperature of EC,which makes it too brittle to be used widely.The hydroxyl group on EC can form a supramolecular system in the form of a non-covalent bond with an effective plasticizer.In this study,an important vegetable-oil-based derivative named dimer fatty acid was used to prepare a novel special plasticizer for EC.Dimer-fatty-acid-based thioether polyol(DATP)was synthesized and used to modify ethyl cellulose films.The supramolecular composite films of DATP and ethyl cellulose were designed using the newly-formed van der Waals force.The thermal stability,morphology,hydrophilicity,and mechanical properties of the composite films were all tested.Pure EC is fragile,and the addition of DATP makes the ethyl cellulose films more flexible.The elongation at the break of EC supramolecular films increased and the tensile strength decreased with the increasing DATP content.The elongation at the break of EC/DATP(60/40)and EC/DATP(50/50)was up to 40.3%and 43.4%,respectively.Noticeably,the thermal initial degradation temperature of the film with 10%DATP is higher than that of pure EC,which may be attributed to the formation of a better supramolecular system in this composite film.The application of bio-based material(EC)is environmentally friendly,and the novel DATP can be used as a special and effective plasticizer to prepare flexible EC films,making it more widely used in energy,chemical industry,materials,agriculture,medicine,and other fields.展开更多
In the present study,the unique three-dimensional graphene coated nickel(Ni/C)foam reinforced silicon carbide(Ni/C@SiC)composites were first obtained via the precursor impregnation and pyrolysis(PIP)processes.The micr...In the present study,the unique three-dimensional graphene coated nickel(Ni/C)foam reinforced silicon carbide(Ni/C@SiC)composites were first obtained via the precursor impregnation and pyrolysis(PIP)processes.The microstructure images indicated that the SiC fillers were successfully prepared in the skeleton pores of the Ni/C foam.The influence of the PIP cycles on the microwave absorption performances was researched,and the results indicated that after the primary PIP process,Ni/C@SiC-I possessed the optimal microwave absorbing performance with a minimum reflection loss(RL)of-25.87 d B at 5.28 GHz and 5.00 mm.Besides,the RL values could be below-10.00 dB from 5.88 GHz to 7.74 GHz when the corresponding matching thickness was 3.85 mm.However,the microwave absorption properties of Ni/C@SiC-II and Ni/C@SiC-Ⅲwere tremendously degraded as the PIP times increased.At last,the electromagnetic parameter,dielectric loss,attenuation constant as well as impedance matching coefficient were further investigated to analyze the absorbing mechanism,which opened a new path for the certain scientific evaluation of the absorbing materials and had extremely important to the defence technology.展开更多
With the continuous demand of material performance,the development of materials is rapid,and the professional curriculum teaching of“new inorganic materials”as well as its teaching methods related to the internet ma...With the continuous demand of material performance,the development of materials is rapid,and the professional curriculum teaching of“new inorganic materials”as well as its teaching methods related to the internet mandate a reform,in order to meet the needs of innovative high-quality personnel training.The update and optimization of the teaching content and methods assisted by the internet meet the needs of modern teaching and research work.More than 90%of students believe that internet teaching is conducive to the understanding of classroom knowledge and the development of innovative projects.展开更多
FeNiCoCrTi0.5 coatings with different process parameters were fabricated by laser cladding. The macro-morphology, phase, microstructure, hardness, and wear resistance of each coating were studied. The smoothness and d...FeNiCoCrTi0.5 coatings with different process parameters were fabricated by laser cladding. The macro-morphology, phase, microstructure, hardness, and wear resistance of each coating were studied. The smoothness and dilution rate of the FeNiCoCrTi0.5 coating generally increased with the increase of specific energy(Es), which is the laser irradiation energy received by a unit area. FeNiCoCrTi0.5 coatings at different parameters had bcc, fcc, and Ti-rich phases as well as equiaxed, dendritic, and columnar structures. When Es increased, the size of each structure increased and the distribution area of the columnar and dendritic structures changed. The prepared FeNiCoCrTi0.5 coating with the Es of 72.22 J·mm-2 had the highest hardness and the best wear resistance, the highest hardness of the coating reached HV 498.37, which is twice the substrate hardness. The average hardness of the FeNiCoCrTi0.5 coating with the Es of 72.22 J·mm-2 was 15.8% higher than the lowest average hardness of the coating with the Es of 108.33 J·mm-2. The worn surface morphologies indicate that the FeNiCoCrTi0.5 coatings exhibited abrasive wear.展开更多
This paper deals with a study on SnPb and lead-free soldered joint reliability of PLCC devices with different lead counts under three kinds of temperature cycle profiles, which is based on non-linear finite element me...This paper deals with a study on SnPb and lead-free soldered joint reliability of PLCC devices with different lead counts under three kinds of temperature cycle profiles, which is based on non-linear finite element method. By analyzing the stress of soldered joints, it is found that the largest stress is at the area between the soldered joints and the leads, and analysis results indicate that the yon Mises stress at the location slightly increases with the increase of lead counts. For PLCC with 84 leads the soldered joints was modeled for three typical loading (273 -398 K, 218 -398 K and 198 -398 K) in order to study the influence of acceleration factors on the reliability of soldered joints. And the estimation of equivalent plastic strain of three different lead-free solder alloys ( Sn3.8AG0. 7Cu, Sn3.5Ag and Sn37Pb ) was also carried out.展开更多
Selective laser melting(SLM)is an emerging additive manufacturing technology for fabricating aluminum alloys and aluminum matrix composites.Nevertheless,it remains unclear how to improve the properties of laser manufa...Selective laser melting(SLM)is an emerging additive manufacturing technology for fabricating aluminum alloys and aluminum matrix composites.Nevertheless,it remains unclear how to improve the properties of laser manufactured aluminum alloy by adding ceramic reinforcing particles.Here the effect of trace addition of TiB2 ceramic(1%weight fraction)on microstructural and mechanical properties of SLM-produced AlSi10Mg composite parts was investigated.The densification level increased with increasing laser power and decreasing scan speed.A near fully dense composite part(99.37%)with smooth surface morphology and elevated inter-layer bonding was successfully obtained.A decrease of lattice plane distance was identified by X-ray diffraction with the laser scan speed decreased,which implied that the crystal lattices were distorted due to the dissolution of Si and TiB2 particles.A homogeneous composite microstructure with the distribution of surface-smoothened TiB2 particles was present,and a small amount of Si particles precipitated at the interface between reinforcing particles and matrix.In contrast to the AlSi10Mg alloy,the composites showed a stabilized microhardness distribution.A higher ultimate tensile strength of 380.0 MPa,yield strength of 250.4 MPa and elongation of 3.43%were obtained even with a trace amount of ceramic addition.The improvement of tensile properties can be attributed to multiple mechanisms including solid solution strengthening,load-bearing strengthening and dispersion strengthening.This research provides a theoretical basis for ceramic reinforced aluminum matrix composites by additive manufacturing.展开更多
We aim in this research at synthesizing high-purity aluminium titanate with sludge from the aluminium profile factory by shock cooling method, and mainly discuss the effect of calcining reaction temperature and holdin...We aim in this research at synthesizing high-purity aluminium titanate with sludge from the aluminium profile factory by shock cooling method, and mainly discuss the effect of calcining reaction temperature and holding time on crystalline, microstructure and content of aluminum titanate materials to determine the preferred calcining temperature and holding time. XRD and SEM methods were utilized to characterize the crystalline and microstructure of each specimen, Rietveld Quantification software was used for the determination of different crystalline contents of specimens, and Philips plus software was applied to determine the cell parameters of aluminium titanate in different specimens. According to the experimental results, preferred calcining temperature is determined as 1400℃ and preferred holding time is 2 h, at which the grains of aluminum titanate grow completely and the purity of aluminum titanate is 97.2wt%.展开更多
Effect of small addition of rare earth on Sn-Ag-Cu solder was investigated by finite element method based on creep model of low stress and high stress and experiments respectively.It was found that addition of rare ea...Effect of small addition of rare earth on Sn-Ag-Cu solder was investigated by finite element method based on creep model of low stress and high stress and experiments respectively.It was found that addition of rare earths evidently improved the resistance to creep deformation of the solder, so that the reliability of Sn-Ag-Cu-Ce solder joint could be improved remarkably.Mechanical testing and microstructural analysis results showed that, mechanical properties of alloys bearing Ce were better than that of the original alloy, and the optimum content of Ce was about 0.03wt.%.After aging intermetallic compound between solder joint and Cu substrate was observed and analyzed by X-ray diffraction(XRD), scanning electron micrographs(SEM) and energy dispersive X-ray fluorescence spectrometer(EDX).Results showed that the thickness of intermetallic compound layer would became thinner when the addition of Ce was about 0.03wt.%, and the grains of intermetallic compound became finer, and the microstructure was more homogeneous than that in the original Sn-Ag-Cu/Cu interface.展开更多
As the rapid development of portable and wearable devices,different electromagnetic interference(EMI)shielding materials with high efficiency have been desired to eliminate the resulting radiation pollution.However,li...As the rapid development of portable and wearable devices,different electromagnetic interference(EMI)shielding materials with high efficiency have been desired to eliminate the resulting radiation pollution.However,limited EMI shielding materials are successfully used in practical applications,due to the heavy thickness and absence of sufficient strength or flexibility.Herein,an ultrathin and flexible carbon nanotubes/MXene/cellulose nanofibrils composite paper with gradient and sandwich structure is constructed for EMI shielding application via a facile alternating vacuum-assisted filtration process.The composite paper exhibits outstanding mechanical properties with a tensile strength of 97.9±5.0 MPa and a fracture strain of 4.6±0.2%.Particularly,the paper shows a high electrical conductivity of 2506.6 S m?1 and EMI shielding effectiveness(EMI SE)of 38.4 dB due to the sandwich structure in improving EMI SE,and the gradient structure on regulating the contributions from reflection and absorption.This strategy is of great significance in fabricating ultrathin and flexible composite paper for highly efficient EMI shielding performance and in broadening the practical applications of MXene-based composite materials.展开更多
The reaction mechanism of glyoxal (G) with urea (U) under weak acid condition was theoretically investigated at PW91/DNP/COSMO of quantum chemistry using density functional theory (DFT) method. The results show ...The reaction mechanism of glyoxal (G) with urea (U) under weak acid condition was theoretically investigated at PW91/DNP/COSMO of quantum chemistry using density functional theory (DFT) method. The results show that the addition reaction of G with U under the conditions mainly involves the reactions of U with protonated glyoxal (p-G), protonated 2,2-dihy- droxyacetaldehyde (p-G 1) and protonated bis-hemdiol (p-G2) to form two important carbocation reactive intermediates of C-p-UG and C-p-UG1, and two important hydroxyl compounds of UG and UG1. These compounds play important roles in the formation of UG resin. According to the result of quantum chemical calculation, UG resin was synthesized successfully under weak acid conditions. The UG resin was characterized by matrix assisted laser desorption ionization time of flight mass spectrometry (MALDI-TOF-MS), ultraviolet and visible spectroscopy (UV-vis), Fourier transform infrared spectroscopy (FT1R) and nuclear magnetic resonance spectroscopy (13CNMR and 1HNMR). These instrumental analytical results agree with each other and further confirm the addition reaction pathway of glyoxal with urea proposed by quantum chemical calculation.展开更多
A three-dimensional laser absorption model based on ray tracing was established to describe the coupled interaction of a laser beam with particles in the powder layers of pure tungsten(W)material processed by selectiv...A three-dimensional laser absorption model based on ray tracing was established to describe the coupled interaction of a laser beam with particles in the powder layers of pure tungsten(W)material processed by selective laser melting(SLM).The influence of particle size on the powder-to-laser absorptivity and underlying absorption behavior was investigated.An intrinsic relationship between the absorption,distribution of absorbed irradiance within the powder layers,and surface morphology and geometric characteristics(e.g.,contact angle,width and height of tracks,and remelted depth)of the laser scanning tracks is presented here.Simulation conclusions indicate that the absorptivity of the powder layers considerably exceeds the single powder particle value or the dense solid material value.With an increase in particle size,the powder layer absorbs less laser energy.The maximum absorptivity of theWpowder layers reached 0.6030 at the particle size of 5 lm.The distribution of laser irradiance on the particle surface was sensitive to particle size,azimuthal angle,and the position of the powder particles on the substrate.The maximum irradiance in the powder layers decreased from 1.117×10^–3 to 0.85×10^–3W·μm^-2 and the contour of the irradiance distribution in the center of the irradiated area gradually contracted when the particle size increased from 5 to 45 lm.An experimental study on the surface morphologies and cross-sectional geometric characteristics of SLM-fabricated W material was performed,and the experimental results validated the mechanisms of the powder-to-laser-absorption behavior that were obtained in simulations.This work provides a scientific basis for the application of the ray-tracing model to predict the wetting and spreading ability of melted tracks during SLM additive manufacturing in order to yield a sound laser processability.展开更多
We aim to present an overview of the status of adhesives in the wood industry, especially in the area of wood-based panels. The review summarizes the current state of research of two kinds of adhesives, i.e., syntheti...We aim to present an overview of the status of adhesives in the wood industry, especially in the area of wood-based panels. The review summarizes the current state of research of two kinds of adhesives, i.e., synthetic adhesives and natural adhesives. Synthetic adhesives, consisting of urea-formaldehyde resins (UF), phenol-formaldehyde resins (PF), polyvinyl acetate emulsion (PVAc) and isocyanates, are widely used. For UF, most investigations are concerned with the reduction of free formaldehyde; for PF, most studies focus on finding new chemicals to replace phenol. PVAc has poor properties, but these can be improved by a blending reactions and copolymerization with other chemicals. Isocyanate is an environmentally friendly synthetic adhesive, but also suffers from inadequate properties. Natural adhesives, such as protein/starch, lignin and tannins, have poor bonding effect that limits their level of use, but their main advantages are that they are environmentally friendly and a renewable resource. Studies of modification can improve the bonding performances and gradually cause natural adhesives to become applied in industrial production. Some proposals for future development and the importance of environmentally friendly adhesives are provided, which will be helpful in future theoretical and experimental research.展开更多
Pretreatment of lespedeza stalks by steam explosion has been studied. The results indicate that steam-exploded pretreatment has strong effects on physical features, morphology, crystallinity, and composition of lesped...Pretreatment of lespedeza stalks by steam explosion has been studied. The results indicate that steam-exploded pretreatment has strong effects on physical features, morphology, crystallinity, and composition of lespedeza stalks as shown by scanning electron microscopy (SEM), infrared (IR), and X-ray diffraction spectrometry methods. After steam explosion, the cellulose and lignin contents of lespedeza stalks varied only slightly, but the hemicellulose content had decreased from 29.34% to 7.48%. The cellulose obtained by steam-exploded pretreatment had a higher degree of crystallinity than that of the raw material. At the explosion condition of 2.25 MPa and 4 min, lignocellulose is easier to hydrolyze by enzyme than the original lignocellulose. The concentration of reduced sugar in the hydrolyzate liquid increased from 71.77 to 162.84 g·L^-1.展开更多
Developing ultrabroad radar-infrared compatible stealth materials has turned into a research hotspot,which is still a problem to be solved.Herein,the copper sulfide wrapped by reduced graphene oxide to obtain three-di...Developing ultrabroad radar-infrared compatible stealth materials has turned into a research hotspot,which is still a problem to be solved.Herein,the copper sulfide wrapped by reduced graphene oxide to obtain three-dimensional(3D)porous network composite aerogels(CuS@rGO)were synthesized via thermal reduction ways(hydrothermal,ascorbic acid reduction)and freeze-drying strategy.It was discovered that the phase components(rGO and CuS phases)and micro/nano structure(microporous and nanosheet)were well-modified by modulating the additive amounts of CuS and changing the reduction ways,which resulted in the variation of the pore structure,defects,complex permittivity,microwave absorption,radar cross section(RCS)reduction value and infrared(IR)emissivity.Notably,the obtained CuS@rGO aerogels with a single dielectric loss type can achieve an ultrabroad bandwidth of 8.44 GHz at 2.8 mm with the low filler content of 6 wt%by a hydrothermal method.Besides,the composite aerogel via the ascorbic acid reduction realizes the minimum reflection loss(RL_(min))of−60.3 dB with the lower filler content of 2 wt%.The RCS reduction value can reach 53.3 dB m^(2),which effectively reduces the probability of the target being detected by the radar detector.Furthermore,the laminated porous architecture and multicomponent endowed composite aerogels with thermal insulation and IR stealth versatility.Thus,this work offers a facile method to design and develop porous rGO-based composite aerogel absorbers with radar-IR compatible stealth.展开更多
First-principles calculations are performed to investigate the relaxation and electronic properties of sulfide minerals surfaces(MoS2, Sb2S3, Cu2 S, ZnS, PbS and FeS2) in presence of H2 O molecule. The calculated resu...First-principles calculations are performed to investigate the relaxation and electronic properties of sulfide minerals surfaces(MoS2, Sb2S3, Cu2 S, ZnS, PbS and FeS2) in presence of H2 O molecule. The calculated results show that the structure and electronic properties of sulfide minerals surfaces have been influenced in presence of H2 O molecule. The adsorption of the flotation reagent at the interface of mineral-water would be different from that of mineral surface due to the changes of surface structures and electronic properties caused by H2 O molecule. Hence, the influence of H2 O molecule on the reaction of flotation reagent with sulfide mineral surface will attract more attention.展开更多
Melting temperature, spreadability, mechanical properties and the microstructures of joints brazed with silver-base filler metals including different amounts of Ga and/or In were studied respectively in this paper, an...Melting temperature, spreadability, mechanical properties and the microstructures of joints brazed with silver-base filler metals including different amounts of Ga and/or In were studied respectively in this paper, and the results show that the melting temperature of the silver-base filler metals is decreased, spreadability of the silver-base filler metals is improved, and the microstructures of silver-base filh, r metals are refined obviously with the addition of Ga and/or In. Using copper and brass plates as base metal and brazing with flame method, the mechanical properties of the lap-joint and butt joint were also examined and analyzed respectively, and the results indicate that the fracture position of two kinds of brazed joints occurred on the base metal, except for the lap-joint of brass, which shows better mechanical properties of the joints brazed with the silver- based filler metals including Ga. For the lap-joint of brass, the tensile strength gradually increased with the increase of Ga content, while the addition of In has little effect on mechanical properties. It is also found that the best comprehensive properties of cadmium-free Ag-Cu-Zn filler metals are obtained when Ga content is about 3.0 wt. % and In content is between 1.5 wt. % and 2. 0 wt. %.展开更多
Soldering experiments of quad flat package(QFP) devices were carried out by means of diode laser soldering system with Sn-Ag-Cu and Sn-Cu-Ni lead-free solders, and competitive experiments were also carried out not onl...Soldering experiments of quad flat package(QFP) devices were carried out by means of diode laser soldering system with Sn-Ag-Cu and Sn-Cu-Ni lead-free solders, and competitive experiments were also carried out not only with Sn-Pb eutectic solders but also with infrared reflow soldering method. The results indicate that under the conditions of laser continuous scanning mode as well as the fixed laser soldering time, an optimal power exists, while the optimal mechanical properties of QFP micro-joints are gained. Mechanical properties of QFP micro-joints soldered with laser soldering system are better than those of QFP micro-joints soldered with IR reflow soldering method. Fracture morphologies of QFP micro-joints soldered with laser soldering system exhibit the characteristic of tough fracture, and homogeneous and fine dimples appear under the optimal laser output power.展开更多
The WC-10%Co particulate reinforced Cu matrix composite material with a WC-Co∶Cu mass ratio of 20∶80 was successfully fabricated by selective laser sintering(SLS) process. The following optimal processing parameters...The WC-10%Co particulate reinforced Cu matrix composite material with a WC-Co∶Cu mass ratio of 20∶80 was successfully fabricated by selective laser sintering(SLS) process. The following optimal processing parameters were used: laser power of 700 W, scan speed of 0.06 m/s, scan line spacing of 0.15 mm, and powder layer thickness of 0.3 mm. The microstructure, composition, and phase of the laser processed material were investigated by scanning electron microscopy(SEM), X-ray diffraction(XRD), and energy dispersive X-ray(EDX) spectroscopy. The results show that the bonding mechanism of this process is liquid phase sintering. The Cu and Co act as the binder phase, while the WC acts as the reinforcing phase. The non-equilibrium effects induced by laser melting, such as high degrees of undercooling and high solidification rate, result in the formation of a metastable phase CoC0.25. The WC reinforcing particulates typically have three kinds of morphology. They are agglomerated and undissolved, incompletely separated and partially dissolved, separated and dissolved, which indicates that particle rearrangement acts as the dominant sintering mechanism for the larger WC, while dissolution-precipitation prevails for the smaller WC particles. Microhardness tester was used to determine the Vickers hardness across the cross-section of the laser sintered sample, with the average value being HV0.1268.5. However, the hardness varied considerably, which might be attributed to the WC segregation and the high solidification rate experienced by the molten pool.展开更多
An orthogonal method was used to evaluate the effects of Ga, Al, Ag, and Ce multi-additions on the wetting characteristics of Sn-9Zn lead-free solders by wetting balance method. The results show that the optimal loadi...An orthogonal method was used to evaluate the effects of Ga, Al, Ag, and Ce multi-additions on the wetting characteristics of Sn-9Zn lead-free solders by wetting balance method. The results show that the optimal loading of Ga, Al, Ag, and Ce was 0.2 wt.%, 0.002 wt.%, 0.25 wt.%, and 0.15 wt.%, respectively. Intermetallic compounds (IMCs) formed at the interface between Sn-9Zn-0.2Ga-0.002Al-0.25Ag- 0.15Ce solder and Cu substrate were investigated by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) analysis. The SEM images illustrate that the IMCs can be divided into two portions from the substrate side to the solder side: a planar CusZns layer and an additional continuous scallop-like AgZn3 layer. The EDS analysis also shows that Ga segregates in the solder abutting upon the interface. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) of the surface components of Sn-9Zn-0.2Ga-0.002Al- 0.25Ag-0.15Ce solder indicate that Al aggregates at the surface in the form of Al203 protective fdm, which prevents the further oxidation of the solder surface. On the other hand, Ce aggregates at the subsurface, which may reduce the surface tension of the solder and improve the wettability in consequence.展开更多
基金supported by the National Nature Science Foundation of China (Nos. 51971111, 52273247)the facilities in the Center for Microscopy and Analysis at Nanjing University of Aeronautics and Astronautics and the Fund of Prospective Layout of Scientific Research for NUAA (Nanjing University of Aeronautics and Astronautics (No. ILA220461A22)。
文摘Wearable devices with efficient thermal management and electromagnetic interference(EMI) shielding are highly desirable for improving human comfort and safety. Herein, a multifunctional wearable carbon fibers(CF) @ polyaniline(PANI)/silver nanowires(Ag NWs) composites with a “branch-trunk” interlocked micro/nanostructure were achieved through "three-in-one" multi-scale design. The reasonable assembly of the three kinds of one-dimensional(1D) materials can fully exert their excellent properties i.e., the superior flexibility of CF, the robustness of PANI, and the splendid conductivity of Ag NWs. Consequently, the constructed flexible composite demonstrates enhanced mechanical properties with a tensile stress of 1.2 MPa, which was almost 6 times that of the original material. This is mainly attributed to the fact that the PNAI(branch) was firmly attached to the CF(trunk) through polydopamine(PDA), forming a robust interlocked structure. Meanwhile, the composite possesses excellent thermal insulation and heat preservation capacity owing to the synergistically low thermal conductivity and emissivity. More importantly, the conductive path of the composite established by the three 1D materials greatly improved its EMI shielding property and Joule heating performance at low applied voltage. This work paves the way for rational utilization of the intrinsic properties of 1D materials, as well as provides a promising strategy for designing wearable electromagnetic protection and thermal energy management devices.
基金supported by Jiangsu Province Biomass Energy and Materials Laboratory,China(Grant No.JSBEM-S-202007).
文摘Ethyl cellulose(EC),an important biomass-based material,has excellent film-forming properties.Nevertheless,the high interchain hydrogen bond interaction leads to a high glass transition temperature of EC,which makes it too brittle to be used widely.The hydroxyl group on EC can form a supramolecular system in the form of a non-covalent bond with an effective plasticizer.In this study,an important vegetable-oil-based derivative named dimer fatty acid was used to prepare a novel special plasticizer for EC.Dimer-fatty-acid-based thioether polyol(DATP)was synthesized and used to modify ethyl cellulose films.The supramolecular composite films of DATP and ethyl cellulose were designed using the newly-formed van der Waals force.The thermal stability,morphology,hydrophilicity,and mechanical properties of the composite films were all tested.Pure EC is fragile,and the addition of DATP makes the ethyl cellulose films more flexible.The elongation at the break of EC supramolecular films increased and the tensile strength decreased with the increasing DATP content.The elongation at the break of EC/DATP(60/40)and EC/DATP(50/50)was up to 40.3%and 43.4%,respectively.Noticeably,the thermal initial degradation temperature of the film with 10%DATP is higher than that of pure EC,which may be attributed to the formation of a better supramolecular system in this composite film.The application of bio-based material(EC)is environmentally friendly,and the novel DATP can be used as a special and effective plasticizer to prepare flexible EC films,making it more widely used in energy,chemical industry,materials,agriculture,medicine,and other fields.
基金supported by the Fundamental Research Funds for the Central Universities (Grant No. D5000210522 and D5000200408)Jiangsu Planned Projects for Postdoctoral Research Funds, National Natural Science Foundation of China [grant number 51772151]+2 种基金Natural Science Foundation of Shaanxi Province (Grant No. 2021JQ-117)Basic Research Programs of Taicang (Grant No.TC2020JC10)Natural Science Foundation of Shandong Province (Grant No. ZR2020QE180)
文摘In the present study,the unique three-dimensional graphene coated nickel(Ni/C)foam reinforced silicon carbide(Ni/C@SiC)composites were first obtained via the precursor impregnation and pyrolysis(PIP)processes.The microstructure images indicated that the SiC fillers were successfully prepared in the skeleton pores of the Ni/C foam.The influence of the PIP cycles on the microwave absorption performances was researched,and the results indicated that after the primary PIP process,Ni/C@SiC-I possessed the optimal microwave absorbing performance with a minimum reflection loss(RL)of-25.87 d B at 5.28 GHz and 5.00 mm.Besides,the RL values could be below-10.00 dB from 5.88 GHz to 7.74 GHz when the corresponding matching thickness was 3.85 mm.However,the microwave absorption properties of Ni/C@SiC-II and Ni/C@SiC-Ⅲwere tremendously degraded as the PIP times increased.At last,the electromagnetic parameter,dielectric loss,attenuation constant as well as impedance matching coefficient were further investigated to analyze the absorbing mechanism,which opened a new path for the certain scientific evaluation of the absorbing materials and had extremely important to the defence technology.
基金the National Natural Science Foundations of China(Grant Number:51772247).
文摘With the continuous demand of material performance,the development of materials is rapid,and the professional curriculum teaching of“new inorganic materials”as well as its teaching methods related to the internet mandate a reform,in order to meet the needs of innovative high-quality personnel training.The update and optimization of the teaching content and methods assisted by the internet meet the needs of modern teaching and research work.More than 90%of students believe that internet teaching is conducive to the understanding of classroom knowledge and the development of innovative projects.
基金This study was supported by the Youth Program of National Natural Science Foundation of China(No.51605473)the National Key R&D Program of China(No.2018YFB1105801).
文摘FeNiCoCrTi0.5 coatings with different process parameters were fabricated by laser cladding. The macro-morphology, phase, microstructure, hardness, and wear resistance of each coating were studied. The smoothness and dilution rate of the FeNiCoCrTi0.5 coating generally increased with the increase of specific energy(Es), which is the laser irradiation energy received by a unit area. FeNiCoCrTi0.5 coatings at different parameters had bcc, fcc, and Ti-rich phases as well as equiaxed, dendritic, and columnar structures. When Es increased, the size of each structure increased and the distribution area of the columnar and dendritic structures changed. The prepared FeNiCoCrTi0.5 coating with the Es of 72.22 J·mm-2 had the highest hardness and the best wear resistance, the highest hardness of the coating reached HV 498.37, which is twice the substrate hardness. The average hardness of the FeNiCoCrTi0.5 coating with the Es of 72.22 J·mm-2 was 15.8% higher than the lowest average hardness of the coating with the Es of 108.33 J·mm-2. The worn surface morphologies indicate that the FeNiCoCrTi0.5 coatings exhibited abrasive wear.
基金the Jiangsu General Colleges and Universities Postgraduate Scientific Research Innovative Plan under Grant No. CX07B_087zthe Six Kind Skilled Personnel Project of Jiangsu Province,under Grant No. 06-E-020
文摘This paper deals with a study on SnPb and lead-free soldered joint reliability of PLCC devices with different lead counts under three kinds of temperature cycle profiles, which is based on non-linear finite element method. By analyzing the stress of soldered joints, it is found that the largest stress is at the area between the soldered joints and the leads, and analysis results indicate that the yon Mises stress at the location slightly increases with the increase of lead counts. For PLCC with 84 leads the soldered joints was modeled for three typical loading (273 -398 K, 218 -398 K and 198 -398 K) in order to study the influence of acceleration factors on the reliability of soldered joints. And the estimation of equivalent plastic strain of three different lead-free solder alloys ( Sn3.8AG0. 7Cu, Sn3.5Ag and Sn37Pb ) was also carried out.
基金Supported by National Key Research and Development Program“Additive Manufacturing and Laser Manufacturing”of China(Grant Nos.2016YFB1100101,2018YFB1106302)National Natural Science Foundation of China(Grant No.51735005)+4 种基金Jiangsu Provincial Natural Science Foundation for Youth(Grant No.BK20180439)National Natural Science Foundation of China for Creative Research Groups(Grant No.51921003)The 15th Batch of“Six Talents Peaks”Innovative Talents Team Program(Grant No.TD-GDZB-001)2017 Excellent Scientific and Technological Innovation Teams of Universities in Jiangsu ProvinceNanjing University of Aeronautics and Astronautics Graduate Innovation Base(Laboratory)Open Fund Project(Grant No.kfjj20190606).
文摘Selective laser melting(SLM)is an emerging additive manufacturing technology for fabricating aluminum alloys and aluminum matrix composites.Nevertheless,it remains unclear how to improve the properties of laser manufactured aluminum alloy by adding ceramic reinforcing particles.Here the effect of trace addition of TiB2 ceramic(1%weight fraction)on microstructural and mechanical properties of SLM-produced AlSi10Mg composite parts was investigated.The densification level increased with increasing laser power and decreasing scan speed.A near fully dense composite part(99.37%)with smooth surface morphology and elevated inter-layer bonding was successfully obtained.A decrease of lattice plane distance was identified by X-ray diffraction with the laser scan speed decreased,which implied that the crystal lattices were distorted due to the dissolution of Si and TiB2 particles.A homogeneous composite microstructure with the distribution of surface-smoothened TiB2 particles was present,and a small amount of Si particles precipitated at the interface between reinforcing particles and matrix.In contrast to the AlSi10Mg alloy,the composites showed a stabilized microhardness distribution.A higher ultimate tensile strength of 380.0 MPa,yield strength of 250.4 MPa and elongation of 3.43%were obtained even with a trace amount of ceramic addition.The improvement of tensile properties can be attributed to multiple mechanisms including solid solution strengthening,load-bearing strengthening and dispersion strengthening.This research provides a theoretical basis for ceramic reinforced aluminum matrix composites by additive manufacturing.
基金supported by the Natural Science Foundation of Fujian Province (No. T08J0129)the Science and Technology Developing Foundation of Fuzhou University (No. 2008-XQ-001)2007-year New Century Talents Supporting Program of Fujian Province (No.XSJRC2007-17)
文摘We aim in this research at synthesizing high-purity aluminium titanate with sludge from the aluminium profile factory by shock cooling method, and mainly discuss the effect of calcining reaction temperature and holding time on crystalline, microstructure and content of aluminum titanate materials to determine the preferred calcining temperature and holding time. XRD and SEM methods were utilized to characterize the crystalline and microstructure of each specimen, Rietveld Quantification software was used for the determination of different crystalline contents of specimens, and Philips plus software was applied to determine the cell parameters of aluminium titanate in different specimens. According to the experimental results, preferred calcining temperature is determined as 1400℃ and preferred holding time is 2 h, at which the grains of aluminum titanate grow completely and the purity of aluminum titanate is 97.2wt%.
文摘Effect of small addition of rare earth on Sn-Ag-Cu solder was investigated by finite element method based on creep model of low stress and high stress and experiments respectively.It was found that addition of rare earths evidently improved the resistance to creep deformation of the solder, so that the reliability of Sn-Ag-Cu-Ce solder joint could be improved remarkably.Mechanical testing and microstructural analysis results showed that, mechanical properties of alloys bearing Ce were better than that of the original alloy, and the optimum content of Ce was about 0.03wt.%.After aging intermetallic compound between solder joint and Cu substrate was observed and analyzed by X-ray diffraction(XRD), scanning electron micrographs(SEM) and energy dispersive X-ray fluorescence spectrometer(EDX).Results showed that the thickness of intermetallic compound layer would became thinner when the addition of Ce was about 0.03wt.%, and the grains of intermetallic compound became finer, and the microstructure was more homogeneous than that in the original Sn-Ag-Cu/Cu interface.
基金financial support from the National Natural Science Foundation of China(31771081,51472259)the Science and Technology Commission of Shanghai Municipality(18ZR1445100)Beijing Forestry University Outstanding Young Talent Cultivation Project(2019JQ03014).
文摘As the rapid development of portable and wearable devices,different electromagnetic interference(EMI)shielding materials with high efficiency have been desired to eliminate the resulting radiation pollution.However,limited EMI shielding materials are successfully used in practical applications,due to the heavy thickness and absence of sufficient strength or flexibility.Herein,an ultrathin and flexible carbon nanotubes/MXene/cellulose nanofibrils composite paper with gradient and sandwich structure is constructed for EMI shielding application via a facile alternating vacuum-assisted filtration process.The composite paper exhibits outstanding mechanical properties with a tensile strength of 97.9±5.0 MPa and a fracture strain of 4.6±0.2%.Particularly,the paper shows a high electrical conductivity of 2506.6 S m?1 and EMI shielding effectiveness(EMI SE)of 38.4 dB due to the sandwich structure in improving EMI SE,and the gradient structure on regulating the contributions from reflection and absorption.This strategy is of great significance in fabricating ultrathin and flexible composite paper for highly efficient EMI shielding performance and in broadening the practical applications of MXene-based composite materials.
基金Supported by the Key Program of the National Natural Science Foundation of China(No.30930074)National Natural Science Foundation of China(No.31260160)
文摘The reaction mechanism of glyoxal (G) with urea (U) under weak acid condition was theoretically investigated at PW91/DNP/COSMO of quantum chemistry using density functional theory (DFT) method. The results show that the addition reaction of G with U under the conditions mainly involves the reactions of U with protonated glyoxal (p-G), protonated 2,2-dihy- droxyacetaldehyde (p-G 1) and protonated bis-hemdiol (p-G2) to form two important carbocation reactive intermediates of C-p-UG and C-p-UG1, and two important hydroxyl compounds of UG and UG1. These compounds play important roles in the formation of UG resin. According to the result of quantum chemical calculation, UG resin was synthesized successfully under weak acid conditions. The UG resin was characterized by matrix assisted laser desorption ionization time of flight mass spectrometry (MALDI-TOF-MS), ultraviolet and visible spectroscopy (UV-vis), Fourier transform infrared spectroscopy (FT1R) and nuclear magnetic resonance spectroscopy (13CNMR and 1HNMR). These instrumental analytical results agree with each other and further confirm the addition reaction pathway of glyoxal with urea proposed by quantum chemical calculation.
文摘A three-dimensional laser absorption model based on ray tracing was established to describe the coupled interaction of a laser beam with particles in the powder layers of pure tungsten(W)material processed by selective laser melting(SLM).The influence of particle size on the powder-to-laser absorptivity and underlying absorption behavior was investigated.An intrinsic relationship between the absorption,distribution of absorbed irradiance within the powder layers,and surface morphology and geometric characteristics(e.g.,contact angle,width and height of tracks,and remelted depth)of the laser scanning tracks is presented here.Simulation conclusions indicate that the absorptivity of the powder layers considerably exceeds the single powder particle value or the dense solid material value.With an increase in particle size,the powder layer absorbs less laser energy.The maximum absorptivity of theWpowder layers reached 0.6030 at the particle size of 5 lm.The distribution of laser irradiance on the particle surface was sensitive to particle size,azimuthal angle,and the position of the powder particles on the substrate.The maximum irradiance in the powder layers decreased from 1.117×10^–3 to 0.85×10^–3W·μm^-2 and the contour of the irradiance distribution in the center of the irradiated area gradually contracted when the particle size increased from 5 to 45 lm.An experimental study on the surface morphologies and cross-sectional geometric characteristics of SLM-fabricated W material was performed,and the experimental results validated the mechanisms of the powder-to-laser-absorption behavior that were obtained in simulations.This work provides a scientific basis for the application of the ray-tracing model to predict the wetting and spreading ability of melted tracks during SLM additive manufacturing in order to yield a sound laser processability.
基金supported by the Teaching Reform Key Research Project of Beijing Forestry University, China (No. BJFU2010JG014)
文摘We aim to present an overview of the status of adhesives in the wood industry, especially in the area of wood-based panels. The review summarizes the current state of research of two kinds of adhesives, i.e., synthetic adhesives and natural adhesives. Synthetic adhesives, consisting of urea-formaldehyde resins (UF), phenol-formaldehyde resins (PF), polyvinyl acetate emulsion (PVAc) and isocyanates, are widely used. For UF, most investigations are concerned with the reduction of free formaldehyde; for PF, most studies focus on finding new chemicals to replace phenol. PVAc has poor properties, but these can be improved by a blending reactions and copolymerization with other chemicals. Isocyanate is an environmentally friendly synthetic adhesive, but also suffers from inadequate properties. Natural adhesives, such as protein/starch, lignin and tannins, have poor bonding effect that limits their level of use, but their main advantages are that they are environmentally friendly and a renewable resource. Studies of modification can improve the bonding performances and gradually cause natural adhesives to become applied in industrial production. Some proposals for future development and the importance of environmentally friendly adhesives are provided, which will be helpful in future theoretical and experimental research.
文摘Pretreatment of lespedeza stalks by steam explosion has been studied. The results indicate that steam-exploded pretreatment has strong effects on physical features, morphology, crystallinity, and composition of lespedeza stalks as shown by scanning electron microscopy (SEM), infrared (IR), and X-ray diffraction spectrometry methods. After steam explosion, the cellulose and lignin contents of lespedeza stalks varied only slightly, but the hemicellulose content had decreased from 29.34% to 7.48%. The cellulose obtained by steam-exploded pretreatment had a higher degree of crystallinity than that of the raw material. At the explosion condition of 2.25 MPa and 4 min, lignocellulose is easier to hydrolyze by enzyme than the original lignocellulose. The concentration of reduced sugar in the hydrolyzate liquid increased from 71.77 to 162.84 g·L^-1.
基金financial support from the National Nature Science Foundation of China(No.51971111).
文摘Developing ultrabroad radar-infrared compatible stealth materials has turned into a research hotspot,which is still a problem to be solved.Herein,the copper sulfide wrapped by reduced graphene oxide to obtain three-dimensional(3D)porous network composite aerogels(CuS@rGO)were synthesized via thermal reduction ways(hydrothermal,ascorbic acid reduction)and freeze-drying strategy.It was discovered that the phase components(rGO and CuS phases)and micro/nano structure(microporous and nanosheet)were well-modified by modulating the additive amounts of CuS and changing the reduction ways,which resulted in the variation of the pore structure,defects,complex permittivity,microwave absorption,radar cross section(RCS)reduction value and infrared(IR)emissivity.Notably,the obtained CuS@rGO aerogels with a single dielectric loss type can achieve an ultrabroad bandwidth of 8.44 GHz at 2.8 mm with the low filler content of 6 wt%by a hydrothermal method.Besides,the composite aerogel via the ascorbic acid reduction realizes the minimum reflection loss(RL_(min))of−60.3 dB with the lower filler content of 2 wt%.The RCS reduction value can reach 53.3 dB m^(2),which effectively reduces the probability of the target being detected by the radar detector.Furthermore,the laminated porous architecture and multicomponent endowed composite aerogels with thermal insulation and IR stealth versatility.Thus,this work offers a facile method to design and develop porous rGO-based composite aerogel absorbers with radar-IR compatible stealth.
基金Project(51164001)supported by the National Natural Science Foundation of China
文摘First-principles calculations are performed to investigate the relaxation and electronic properties of sulfide minerals surfaces(MoS2, Sb2S3, Cu2 S, ZnS, PbS and FeS2) in presence of H2 O molecule. The calculated results show that the structure and electronic properties of sulfide minerals surfaces have been influenced in presence of H2 O molecule. The adsorption of the flotation reagent at the interface of mineral-water would be different from that of mineral surface due to the changes of surface structures and electronic properties caused by H2 O molecule. Hence, the influence of H2 O molecule on the reaction of flotation reagent with sulfide mineral surface will attract more attention.
文摘Melting temperature, spreadability, mechanical properties and the microstructures of joints brazed with silver-base filler metals including different amounts of Ga and/or In were studied respectively in this paper, and the results show that the melting temperature of the silver-base filler metals is decreased, spreadability of the silver-base filler metals is improved, and the microstructures of silver-base filh, r metals are refined obviously with the addition of Ga and/or In. Using copper and brass plates as base metal and brazing with flame method, the mechanical properties of the lap-joint and butt joint were also examined and analyzed respectively, and the results indicate that the fracture position of two kinds of brazed joints occurred on the base metal, except for the lap-joint of brass, which shows better mechanical properties of the joints brazed with the silver- based filler metals including Ga. For the lap-joint of brass, the tensile strength gradually increased with the increase of Ga content, while the addition of In has little effect on mechanical properties. It is also found that the best comprehensive properties of cadmium-free Ag-Cu-Zn filler metals are obtained when Ga content is about 3.0 wt. % and In content is between 1.5 wt. % and 2. 0 wt. %.
基金Project(CX07B_087z) supported by Jiangsu General Colleges and Universities Postgraduate Scientific Research Innovative Plan, ChinaProject(06-E-020) supported by the Six Kind Skilled Personnel Project of Jiangsu Province, China
文摘Soldering experiments of quad flat package(QFP) devices were carried out by means of diode laser soldering system with Sn-Ag-Cu and Sn-Cu-Ni lead-free solders, and competitive experiments were also carried out not only with Sn-Pb eutectic solders but also with infrared reflow soldering method. The results indicate that under the conditions of laser continuous scanning mode as well as the fixed laser soldering time, an optimal power exists, while the optimal mechanical properties of QFP micro-joints are gained. Mechanical properties of QFP micro-joints soldered with laser soldering system are better than those of QFP micro-joints soldered with IR reflow soldering method. Fracture morphologies of QFP micro-joints soldered with laser soldering system exhibit the characteristic of tough fracture, and homogeneous and fine dimples appear under the optimal laser output power.
基金Project(10276017) supported by the Joint Fund of National Natural Science Foundation of China and China Academy of Engineering Physics Project(04H52061) supported by the Aeronautical Science Foundation of China Project(S0403-061) supported by the Scientific Research Innovations Foundation of Nanjing University of Aeronautics and Astronautics
文摘The WC-10%Co particulate reinforced Cu matrix composite material with a WC-Co∶Cu mass ratio of 20∶80 was successfully fabricated by selective laser sintering(SLS) process. The following optimal processing parameters were used: laser power of 700 W, scan speed of 0.06 m/s, scan line spacing of 0.15 mm, and powder layer thickness of 0.3 mm. The microstructure, composition, and phase of the laser processed material were investigated by scanning electron microscopy(SEM), X-ray diffraction(XRD), and energy dispersive X-ray(EDX) spectroscopy. The results show that the bonding mechanism of this process is liquid phase sintering. The Cu and Co act as the binder phase, while the WC acts as the reinforcing phase. The non-equilibrium effects induced by laser melting, such as high degrees of undercooling and high solidification rate, result in the formation of a metastable phase CoC0.25. The WC reinforcing particulates typically have three kinds of morphology. They are agglomerated and undissolved, incompletely separated and partially dissolved, separated and dissolved, which indicates that particle rearrangement acts as the dominant sintering mechanism for the larger WC, while dissolution-precipitation prevails for the smaller WC particles. Microhardness tester was used to determine the Vickers hardness across the cross-section of the laser sintered sample, with the average value being HV0.1268.5. However, the hardness varied considerably, which might be attributed to the WC segregation and the high solidification rate experienced by the molten pool.
文摘An orthogonal method was used to evaluate the effects of Ga, Al, Ag, and Ce multi-additions on the wetting characteristics of Sn-9Zn lead-free solders by wetting balance method. The results show that the optimal loading of Ga, Al, Ag, and Ce was 0.2 wt.%, 0.002 wt.%, 0.25 wt.%, and 0.15 wt.%, respectively. Intermetallic compounds (IMCs) formed at the interface between Sn-9Zn-0.2Ga-0.002Al-0.25Ag- 0.15Ce solder and Cu substrate were investigated by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) analysis. The SEM images illustrate that the IMCs can be divided into two portions from the substrate side to the solder side: a planar CusZns layer and an additional continuous scallop-like AgZn3 layer. The EDS analysis also shows that Ga segregates in the solder abutting upon the interface. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) of the surface components of Sn-9Zn-0.2Ga-0.002Al- 0.25Ag-0.15Ce solder indicate that Al aggregates at the surface in the form of Al203 protective fdm, which prevents the further oxidation of the solder surface. On the other hand, Ce aggregates at the subsurface, which may reduce the surface tension of the solder and improve the wettability in consequence.