Cutting Experiment of Fraxinus mandshurica UsingWaterjet-Assisted CO_(2)Laser

High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.

Effects of zinc on static and dynamic mechanical properties of copper-zinc alloy

The effects of adding alloy element zinc on the static and dynamic mechanical properties of copper-zinc alloy were investigated. Tensile and low cycle fatigue behaviors of the C11000 copper and H63 copper-zinc alloy were obtained by using a miniature tester that combined the functions of in situ tensile and fatigue testing. A piezoelectric actuator was adopted as the actuator for the fatigue testing, and the feasibility of the fatigue actuator was verified by the transient harmonic response analysis based on static tensile preload and dynamic sinusoidal load. The experimental results show that the yield strength and tensile strength of the C11000 copper are improved after adding 37%(mass fraction) zinc, and H63 copper-zinc alloy presents more obvious cyclic hardening behavior and more consumed irreversible plastic work during each stress cycle compared with C11000 copper for the same strain controlled cycling. Additionally, based on the Manson-Coffin theory, the strain-life equations of the two materials were also obtained. C11000 copper and H63 copper-zinc alloy show transition life of 16832 and 1788 cycles, respectively.

Characteristics and mechanism investigation on drag reduction of oblique riblets

This work primarily focuses on the drag reduction characteristics and mechanism investigation of oblique riblets. First, a calculation model of the oblique riblets surface is established, and Reynolds stress model(RSM) turbulence model is used for numerical simulation of the oblique riblets flow field. Subsequently, the influence of inclination angle between flow direction and arrangement direction of riblets on friction resistance and drag reduction rate is further analyzed. Through the investigation of the distribution of shear stress, pressure stress and velocity in oblique riblets boundary layer, the oblique riblets drag reduction mechanism is finally revealed. Results show that, with increase of velocity and inclination angle, the pressure resistance increases obviously, along with the decreasing of the viscous resistance distinctly. The maximum drag reduction rate of the oblique riblets is 7.33%. Moreover, when the inclination angle increases, the wall shear stress reduces on oblique riblets surface; while differential pressure increases at both sides of oblique riblets tips. In addition, when inclination angle is small, the secondary vortex at oblique riblets tips will disappear soon. New vortices will be formed inside the oblique riblets and cause the decrease of viscosity resistance. Thus, oblique riblets show a better drag reduction effect and have an effective control on boundary layer.

Dynamic simulation and experimental study of inspection robot for high-voltage transmission-line

A mobile robot developed by Wuhan University for full-path hotline inspection on 220 kV transmission lines was presented. With 4 rotating joints and 2 translational ones, such robot is capable of traveling along non- obstaclestraight-line segment and surmounting straight-line segment obstacles as well as transferring between two spans automatically. Lagrange’s equations were utilized to derive dynamic equations of all the links, including items of inertia, coupling inertia, Coriolis acceleration, centripetal acceleration and gravity. And a dynamic response experiment on elemental motions of robot prototype’s travelling along non-obstacle straight-line segment and surmounting obstacles was performed on 220 kV 1∶1 simulative overhanging transmission-line in laboratory. In addition, dynamic numerical simulation was conducted in the corresponding condition. Comparison and analysis on results of experiment and numerical simulation have validated theoretical model and simulation resolution. Therefore, the dynamic model formed hereunder can be used for the study of robot control.

Design and Analysis of the Gemini Chain System in Dual Clutch Transmission of Automobile

Chain drive system is widely used in the conditions of high-speed, overload, variable speed and load, Many studies are focused on the meshing theory and wear characteristics of chain drive system, but system design, analysis, and noise characteristics of the chain drive system are weak. System design and noise characteristic are studied for a new type Gemini chain of dual-clutch automatic transmission. Based on the meshing theory of silent chain, the design parameters of the Gemini chain system are calculated and the mathematical models and dynamic analysis models of the Gemini chain system are established. Dynamic characteristics of the Gemini chain system is simulated and the contact force of plate and pin, plate and sprockets, the chain tension forces, the transmission error and the stress of plates and pins are analyzed. According to the simulation results of the Gemini chain system, the noise experiment about system is carried out. The noise values are tested at different speed and load and spectral characteristics are analyzed. The results of simulation and experimental show that the contact forces of plate and pin, plate and sprockets are smaller than the allowable stress values, the chain tension force is less than ultimate tension and transmission error is limited in 1.2%. The noise values can meet the requirements of industrial design, and it is proved that the design and analysis method of the Gemini chain system is scientific and feasible. The design and test system is built from analysis to test of Gemini chain system. This research presented will provide a corresponding theoretical guidance for the design and dynamic characteristics and noise characteristics of chain drive system.

Time between failures model and failure analysis of CNC system

To provide basis for the reliability improvement design of CNC system, the failure data of a type of CNC system in one year are collected under field conditions in workshops. The distribution model parameters of time between failures are estimated by least square method and hypothesis testing is done by d-test method. It is proved that the time between failures of the CNC system follows Weibull distribution and the system has entered into the wear-out failure period. The failure positions and failure causes are analyzed further to indicate the weak subsystems of the CNC system. It can be found that servo unit, electrical system, detecting unit and power supply are principal failure positions and the main failure cause is breakage of components. The corresponding improvement measures are put forward. The paper provides a reference to reliability design and analysis of CNC system for the manufacturer and has great guidance to using and maintaining CNC system for the user.

PROPER CONDITIONS OF MESHING FOR Hy-Vo SILENT CHAIN AND SPROCKET

Proper meshing of Hy-Vo silent chain and sprocket is important for realizing the transmission of the silent chain with more efficiency and less noise. Based on the study of the meshing theory of the Hy-Vo silent chain with the sprocket and the roll cutting machining principle of the sprocket with the hob, the proper conditions of the meshing for the Hy-Vo silent chain and the sprocket are put forward with the variable pitch characteristic of the Hy-Vo silent chain taken into consideration, and the proper meshing design method on the condition that the value of the link tooth pressure angle is unequal to the value of the sprocket tooth pressure angle is studied. Experiments show that this new design method is feasible. In addition, the design of the pitch, the sprocket tooth pressure angle and the fillet radius of the sprocket addendum circle are studied. It is crucial for guiding the design of the hob which cuts the Hy-Vo silent chain sprocket.

MESHING THEORY AND DESIGN METHOD OF NEW SILENT CHAIN AND SPROCKET

Based on the study of the meshing theory of a new silent chain and sprockets, and the rolling cutting theory of sprocket and hob, the harmonious relations of dominating dimensions among the new silent chain, sprocket and hob is build, the meshing conditions are expatiated, and the resolved expression, which can instruct design and calculation, is educed. The tests show that the meshing design method is feasible.

WEAR FAILURE MECHANISM AND MULTI-IMPACT PROPERTY OF AUTOMOTIVE ENGINE CHAIN

The multi-impact characteristics and failure mechanism of two kinds of automotive engine chain made in China are studied through engine assembly and road-drive tests. The worn surface morphologies of rubbing area between pin, bush and roller are also analyzed based on scanning electron microscope. The results show that the main wear mechanism of automotive engine chain is fatigue wear, and its failure mechanism is the forming, extending and flaking of cracks on top layer of pin and bush. In addition, the material, hot-treatment method and shaping technique for roller have a great influence upon the resistance to multi-impact. Ensuring sufficient strength and plasticity of roller, as well as adopting suitable shaping technique are the effective method to increase its resistance to multi-impact.

Prediction and Analysis of Post-Treatment of Sustainable Walnut Shell/Co-PES Parts by Laser Sintering

In order to enhance the strength of sustainable walnut shell/Co-PES(WSPC)sintered parts,wax-filtrated posttreatment was carried out.The effects of treating fluid temperature,preheating time and immersion time on the bending strength of WSPC wax-filtrated parts were analyzed by single factor analysis method.To obtain an accurate model for predicting the bending strength of the WSPC wax-filtrated part,the experiments were involved by using Box-Behnken design(BBD).Main parameters,such as treating fluid temperature,preheating time and immersion time,and their interactive effects were analyzed through analysis of variance(ANOVA)and graphical contours.The results demonstrated that all parameters’direct effects were significant to bending strength of the WSPC wax-filtrated part.Its optimum value was 5.0 MPa when the treating fluid temperature of 70°C,preheating time of 50 min,and immersion time of 20 s.The predicted models effectively validated had good predicting accuracy.The WSPC wax-filtrated part using optimal processing parameters was processed by investment casting,and then the metal casting of dimensional stability and smooth surface was obtained.Investment casting was done using WSPC wax-filtrated parts under optimal process parameters and then metal parts with stable structure size and smooth surface can be obtained,which indicates that WSPC material can be used for investment casting.

Hand-Held Surgical Instrument with the Function of Self-Locking for Minimally Invasive Surgery

In order to improve the flexibility of the surgical instruments, a wire-driven wrist-like structure is proposed in this paper. The instrument has three degrees of freedom (DOFs) of rotation, yaw, opening and closing. Furthermore, we also acknowledge no coupling motion for each DOF. Moreover, the self-locking motion contributes to sustaining joint posture under external force. A static analysis for the end effector was conducted using the ANSYS software. At the end of this paper, a series of experiments for the prototype was performed. The results revealed that for the same surgical task, the proposed instrument had higher flexibility and the completion time of the operation tasks was obviously less than that of the traditional instrument. The results of the self-locking and operating force test showed that the surgical instruments perform well in maintaining joint posture under the force of 8.2N. The proposed surgical instrument meets the requirements of minimally invasive surgery (MIS).

Modeling and Analysis of Transitional Tube with Constant Sectional Area along Derivative Central Route

Firstly, sample square-circular transition tube along straight central route was modeled on CATIA software. The parameters are as follows： let the tube length is L, and the constant cross section area is S, and S = πR^2 = a2, in which R stands for the circle radius on one end, and a the square side length on the other end; set up the coordinate system with OX axis on the central route in which the origin O is on centroid of the square end and assume the cross section size at x as the square shaped with all four comers filleted in radius r which is proportional to x, that is, the linear slope of r is R/L, thus, both values r and square side length ax can be attained on the constant cross section area assumption. Secondly, some sample polygonal-circular transition tubes along straight, circular and helical central route were implemented similarly. Thirdly, numerical analysis of stress and displacement of these tubes were carried out on MSC/PATRAN software which are important to the distribution of turbulent flow and the layout of these transitional tube structures.

Simulation Analysis of Stress Field of Walnut Shell Composite Powder in Laser Additive Manufacturing Forming

A calculation model of stress field in laser additive manufacturing of walnut shell composite powder(walnut shell/Co-PES powder)was established.The DFLUX subroutine was used to implement the moveable application of a double ellipsoid heat source by considering the mechanical properties varying with temperature.The stress field was simulated by the sequential coupling method,and the experimental results were in good accordance with the simulation results.In addition,the distribution and variation of stress and strain field were obtained in the process of laser additive manufacturing of walnut shell composite powder.The displacement of laser additive manufacturing walnut shell composite parts gradually decreased with increasing preheating temperature,decreasing laser power and increasing scanning speed.During the cooling process,the displacement of laser additive manufacturing of walnut shell composite parts gradually increased with the increasing preheating temperature,decreasing scanning speed and increasing laser power.

Effects of Different Ventilation Modes and Outlet Height on Nursery Piggery Environment

In order to study the effects of ventilation modes and outlet height on the airflow field of a nursery piggery,computational fluid dynamics (CFD) technology was used to simulate the wind speed and temperature of an experimental pig house in the cold northern region.This study was conducted with simulation and a comparative analysis of transverse ventilation,longitudinal ventilation and roof air intake modes.Furthermore,the effects of the air outlet height of 0.7,0.6 and 0.5 m with the roof air inlet mode on the environment in the pig house were studied.Field experiments verified the model of roof air intake model.The results showed inadequate ventilation in both the vertical and horizontal ventilation.However,the airfield gradients were less variable and more balanced when using the rooftop air intake mode.The variation of outlet height significantly affected nursery pig houses’ airflow velocity and temperature.Roof air inlet mode with an outlet height of 0.7 m was better than the other two.The normalized mean square error (NMSE) of air velocity and temperature was less than 0.01,and the simulation analysis could genuinely reflect the distribution of the airflow field in the nursery.

Prediction and Analysis of Surface Quality of Northeast China Ash Wood during Water-Jet Assisted CO_(2) Laser Cutting

As a natural and environmentally friendly renewable material,Northeast China ash wood(NCAW)(Fraxinus mandshurica Rupr.)was cut by water-jet assisted CO_(2) laser(WACL),the surface quality was evaluated by surface roughness of cut section.The surface roughness was measured by three-dimensional(3D)profilometry.Furthermore,the micromorphology of machined surface was observed by scanning electronic microscopy(SEM).Carbon content changes of machined surface were measured by energy dispersive spectrometer(EDS).A relationship between surface roughness and cutting parameters was established using response surface methodology(RSM).It is concluded that the cutting speed,laser power and water pressure played an important role in surface roughness of cut section.The surface roughness increased as an increase in laser power.It decreased caused by increasing of cutting speed and water pressure.Measurements revealed that the surface quality of NCAW part was improved using the optimized combination of cutting parameters.The established quadratic mathematical model of a good prediction is helpful for matching suitable cutting parameters to obtain expected surface quality.

A Blend of Subdivision Surfaces and NURBS

In present paper, the contour deletion method is developed both to blend surfaces and to fill N-sided holes, which is used for subdividing the NURBS surface. First, according to the non-uniform Catmull-Clark subdivision principle, surfaces are blended. The non-uniform Catmull-Clark subdivision method is constructed, which build the surface through interpolating comer vertices and boundary curves. Then the contour deletion method is adapted to remove the controlling mesh boundary contour in the process of segmentation iteration. Last, N sided-hole is filled to generate a integral smooth continuous surface. This method not only guarantee that the blending surface and base surface patches have C2 continuity at the boundary, but also greatly improve the smoothness of the N-side hole filling surface. The results show that, this method simplifies the specific computer-implemented process, broads the scope of application of subdivision surfaces, and solves the incompatible problem between the subdivision surface and classical spline. The resulting surface has both advantages of the subdivision surface and classical spline, and also has better filling effect.

Reliability Design for Impact Vibration of Hydraulic Pressure Pipeline Systems

The research of reliability design for impact vibration of hydraulic pressure pipeline systems is still in the primary stage,and the research of quantitative reliability of hydraulic components and system is still incomplete.On the condition of having obtained the numerical characteristics of basic random parameters,several techniques and methods including the probability statistical theory,hydraulic technique and stochastic perturbation method are employed to carry out the reliability design for impact vibration of the hydraulic pressure system.Considering the instantaneous pressure pulse of hydraulic impact in pipeline,the reliability analysis model of hydraulic pipeline system is established,and the reliability-based optimization design method is presented.The proposed method can reflect the inherent reliability of hydraulic pipe system exactly,and the desired result is obtained.The reliability design of hydraulic pipeline system is achieved by computer programs and the reliability design information of hydraulic pipeline system is obtained.This research proposes a reliability design method,which can solve the problem of the reliability-based optimization design for the hydraulic pressure system with impact vibration practically and effectively,and enhance the quantitative research on the reliability design of hydraulic pipeline system.The proposed method has generality for the reliability optimization design of hydraulic pipeline system.

NUMERICAL SOLUTION OF FLUID-STRUCTURE INTERACTION IN LIQUID-FILLED PIPES BY METHOD OF CHARACTERISTICS

Fluid-structure interaction （FSI） is essentially a dynamic phenomenon and always exists in fluid-filled pipe system. The four-equation model, which has been proved to be effective to describe and predict the phenomenon of FSI due to friction coupling and Poisson coupling being taken into account, is utilized to describe the FSI of fluid-filled pipe system. Terse compatibility equations are educed by the method of characteristics （MOC） to describe the fluid-filled pipe system. To shorten computing time needed to get the solutions under the condition of keeping accuracy requirement, two steps are adopted, firstly the time step Δt and divided number of the straight pipe are optimized, sec-ondly the mesh spacing Δz close to boundary is subdivided in several submeshes automatically ac-cording to the speed gradient of fluid. The mathematical model and arithmetic are validated by com-parisons between simulation solutions of two straight pipe systems and experiment known from lit-erature.

Reliability Evaluation of Machine Center Components Based on Cascading Failure Analysis

In order to rectify the problems that the com- ponent reliability model exhibits deviation, and the evalu- ation result is low due to the overlook of failure propagation in traditional reliability evaluation of machine center components, a new reliability evaluation method based on cascading failure analysis and the failure influ- enced degree assessment is proposed. A direct graph model of cascading failure among components is established according to cascading failure mechanism analysis and graph theory. The failure influenced degrees of the system components are assessed by the adjacency matrix and its transposition, combined with the Pagerank algorithm. Based on the comprehensive failure probability function and total probability formula, the inherent failure proba- bility function is determined to realize the reliability evaluation of the system components. Finally, the method is applied to a machine center, it shows the following： 1） The reliability evaluation values of the proposed method are at least 2.5% higher than those of the traditional method; 2） The difference between the comprehensive and inherent reliability of the system component presents a positive correlation with the failure influenced degree ofthe system component, which provides a theoretical basis for reliability allocation of machine center system.