Functionally graded structure of a nitride-strengthened Mg_(2)Si-based hybrid composite

The ex-situ incorporation of the secondary SiC reinforcement,along with the in-situ incorporation of the tertiary and quaternary Mg_(3)N_(2) and Si_(3)N_(4) phases,in the primary matrix of Mg_(2)Si is employed in order to provide ultimate wear resistance based on the laser-irradiation-induced inclusion of N_(2) gas during laser powder bed fusion.This is substantialized based on both the thermal diffusion-and chemical reactionbased metallurgy of the Mg_(2)Si–SiC/nitride hybrid composite.This study also proposes a functional platform for systematically modulating a functionally graded structure and modeling build-direction-dependent architectonics during additive manufacturing.This strategy enables the development of a compositional gradient from the center to the edge of each melt pool of the Mg_(2)Si–SiC/nitride hybrid composite.Consequently,the coefficient of friction of the hybrid composite exhibits a 309.3%decrease to–1.67 compared to–0.54 for the conventional nonreinforced Mg_(2)Si structure,while the tensile strength exhibits a 171.3%increase to 831.5 MPa compared to 485.3 MPa for the conventional structure.This outstanding mechanical behavior is due to the(1)the complementary and synergistic reinforcement effects of the SiC and nitride compounds,each of which possesses an intrinsically high hardness,and(2)the strong adhesion of these compounds to the Mg_(2)Si matrix despite their small sizes and low concentrations.

Tuning desolvation kinetics of in-situ weakly solvating polyacetal electrolytes for dendrite-free lithium metal batteries

The host structure of polymers significantly influences ion transport and interfacial stability of electrolytes,dictating battery cycle life and safety for solid-state lithium metal batteries.Despite promising properties of ethylene oxide-based electrolytes,their typical clamp-like coordination geometry leads to crowd solvation sheath and overly strong interactions between Li^(+)and electrolytes,rendering difficult dissociation of Li+and unfavorable solid electrolyte interface(SEI).Herein,we explore weakly solvating characteristics of polyacetal electrolytes owing to their alternately changing intervals between–O–coordinating sites in the main chain.Such structural asymmetry leads to unique distorted helical solvation sheath,and can effectively reduce Li^(+)-electrolyte binding and tune Li^(+)desolvation kinetics in the insitu formed polymer electrolytes,yielding anion-derived SEI and dendrite-free Li electrodeposition.Combining with photoinitiated cationic ring-opening polymerization,polyacetal electrolytes can be instantly formed within 5 min at the surface of electrode,with high segmental chain motion and well adapted interfaces.Such in-situ polyacetal electrolytes enabled more than 1300-h of stable lithium electrodeposition and prolonged cyclability over 200 cycles in solid-state batteries at ambient temperatures,demonstrating the vital role of molecular structure in changing solvating behavior and Li deposition stability for high-performance electrolytes.

Ultrasensitive detection of methamphetamine by antibody-modified transistor assay

Effective detection of methamphetamine(Met)requires a fast,sensitive,and cheap testing assay.However,commercially available methods require expensive instruments and highly trained operators,which are time-consuming and labor-intensive.Herein,an antibody-modified graphene transistor assay is developed for sensitive and minute-level detection of Met in complex environments.The anti-Met probe captured charged targets within 120 s,leading to a p-doping effect near the graphene channel.The limit of detection reaches 50 aM(5.0×10^(-17)M)Met in solution.The graphene transistor would be a valuable tool for Met detection effective prevention of drug abuse.

Construction of 3D Shape-Changing Hydrogels via Light-Modulated Internal Stress Fields

The 3D shape-changing hydrogels are highly pursued for numerous applications.However,up to now,the construction of complex 3D shape-changing hydrogels remains a challenge.The reported design strategies are mainly applied to fabricate 2D ones by introducing anisotropic microstructures into hydrogel sheets/membranes.Herein,we present a convenient photolithography strategy for constructing complex 3D shape-changing hydrogels by simultaneously modulating anisotropic microstructures and internal stress fields of gel sheets.When the precursor solution containing ultraviolet(UV)absorber is irradiated by single-side UV light,the attenuated polymerization rate can cause the generation of asymmetric internal stress field in the resulting hydrogel sheet.In the meantime,the directional diffusion of unpolymerized monomers allows for the formation of vertical gradient structure within hydrogel.Therefore,by applying different photomasks to modulate the local gradient structures and internal stress fields of the gel sheets,they can spontaneously transform into various complex 3D shape-changing hydrogels in the air.Response to the external stimuli,these 3D shape-changing hydrogels(e.g.,fighter plane,birdie,and multi-storey origami lattices)can deform in a novel 3D_(1)-to-3D_(2)-to-3D_(3)mode.This new design strategy contributes to the development of complex biomedical implants and soft robotics.

“Three‐in‐one”strategy:Heat regulation and conversion enhancement of a multifunctional separator for safer lithium-sulfur batteries

The safety problems encountered with lithium–sulfur batteries(LSBs)hinder their development for practical applications.Herein,a highly thermally conductive separator was constructed by cross‐weaving super‐aligned carbon nanotubes(SA‐C)on super‐aligned boron nitride@carbon nanotubes(SA‐BC)to create a composite film(SA‐BC/SA‐C).This separator was used to fabricate safe LSBs with improved electrochemical performance.The highly aligned separator structure created a uniform thermal field that could rapidly dissipate heat accumulated during continuous operation due to internal resistance,which prevented the development of extremely high temperatures.The array of boron nitride nanosheets endowed the composite separator with a large number of adsorption sites,while the highly graphitized carbon nanotube skeleton accelerated the catalytic conversion of high‐valence polysulfides into low‐valence polysulfides.The arrayed molecular brush design enabled the regulation of local current density and ion flux,and considerably alleviated the growth of lithium dendrites,thus promoting the smooth deposition of Li metal.Consequently,a battery constructed with the SA‐BC/SA‐C separator showed a good discharge capacity of 685.2 mAh g−1 over 300 cycles(a capacity decay of 0.026%per cycle)at 2 C and 60°C.This“three‐in‐one”multifunctional separator design strategy constitutes a new path forward for overcoming the safety problems of LSBs.

Effect of temperature on the morphology of nanobubbles at mica/water interface

The great implication of nanobubbles at a solid/water interface has drawn wide attention of the scientific community and industries. However, the fundamental properties of nanobubbles remain unknown as yet. In this paper, the temperature effects on the morphology of nanobubbles at the mica/water interface are explored through the combination of AFM direct image with the temperature control. The results demonstrate that the apparent height of nanobubbles in AFM images is kept almost constant with the increase of temperature, whilst the lateral size of nanobubbles changes significantly. As the temperature increases from 28℃ to 42℃, the lateral size of nanobubbles increases, reaching a maximum at about 37℃, and then decreases at a higher temperature. The possible explanation for the size change of nanobubbles with temperature is suggested.

Differentiation of smooth muscle progenitor cells in peripheral blood and its application in tissue engineered blood vessels

Background: A major shortcoming in tissue engineered blood vessels (TEBVs) is the lack of healthy and easily attainable smooth muscle cells (SMCs). Smooth muscle progenitor cells (SPCs), especially from peripheral blood, may offer an alternative cell source for tissue engineering involving a less invasive harvesting technique. Methods: SPCs were isolated from 5-ml fresh rat peripheral blood by density-gradient centrifugation and cultured for 3 weeks in endothelial growth medium-2-MV (EGM-2-MV) medium containing platelet-derived growth factor-BB (PDGF BB). Before seeded on the synthesized scaffold, SPC-derived smooth muscle outgrowth cell (SOC) phenotypes were assessed by immuno-fluorescent staining, Western blot analysis, and reverse transcription polymerase chain reaction (RT-PCR). The cells were seeded onto the silk fibroin-modified poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (SF-PHBHHx) scaffolds by 6×104 cells/cm2 and cultured under the static con- dition for 3 weeks. The growth and proliferation of the seeded cells on the scaffold were analyzed by 3-(4,5-dimethylthiazol-2-yl)- diphenyltetrazolium bromide (MTT) assay, scanning electron microscope (SEM), and 4,6-diamidino-2-phenylindole (DAPI) staining. Results: SOCs displayed specific "hill and valley" morphology, expressed the specific markers of the SMC lineage: smooth muscle (SM) α-actin, calponin and smooth muscle myosin heavy chain (SM MHC) at protein and messenger ribonucleic acid (mRNA) levels. RT-PCR results demonstrate that SOCs also expressed smooth muscle protein 22α (SM22α), a contractile protein, and extracellular matrix components elastin and matrix Gla protein (MGP), as well as vascular endothelial growth factor (VEGF). After seeded on the SF-PHBHHx scaffold, the cells showed excellent metabolic activity and proliferation. Conclusion: SPCs isolated from peripheral blood can be differentiated into the SMCs in vitro and have an impressive growth potential in the biodegradable synthesized scaffold. Thus, SPCs may be a promising cell source for constructing TEBVs.

FORMATION AND MICROSTRUCTURE OF POLYETHYLENE MICROPOROUS MEMBRANES THROUGH THERMALLY INDUCED PHASE SEPARATION

Microporous membranes of low-high density polyethylene and their blends were prepared bythermally-induced phase separation of polymer/long-aliphatic chain alcohol (diluent) mixtures.The microstructures of this particular membrane, which depends on the diluent properties,polymer concentration and cooling rate, were observed by scanning electron microscopy.'Beehive-type,'leafy-like, and lacy porous structure morphologies can be formed,depending onthe blend composition and phase separation conditions, which were discussed by the polymer anddiluent crystallization processes.

Ten years of carbon-based metal-free electrocatalysts

Since the discovery of the first carbon-based metal-free electrocatalysts(C-MFECs,i.e.,N-doped carbon nanotubes)for the oxygen reduction reaction in 2009,the field of C-MFECs has grown enormously over the last 10 years.C-MFECs,as alternatives to nonprecious transition metals and/or precious noble metal-based electrocatalysts,have been consistently demonstrated as efficient catalysts for oxygen reduction,oxygen evolution,hydrogen evolution,carbon dioxide reduction,nitrogen reduction,and many other(electro-)chemical reactions.Recent research and development of C-MFECs have indicated their potential applications in fuel cells,metal-air batteries,and hydrogen generation through water oxidation as well as electrochemical production of various commodity chemicals,such as ammonia,alcohols,hydrogen peroxide,and other useful hydrocarbons.Further research and development of C-MFECs would surely revolutionize traditional energy conversion and storage technologies with minimal environmental impact.In this short review article,we summarize the journey of C-MFECs over the past 10 years with an emphasis on materials development and their structure-property characterization for applications in fuel cells and metal-air batteries.Current challenges and future prospects of this emerging field are also discussed.

Controlled Assembly of Luminescent Lanthanide‑Organic Frameworks via Post‑Treatment of 3D‑Printed Objects

Complex multiscale assemblies of metal-organic frameworks are essential in the construction of largescale optical platforms but often restricted by their bulk nature and conventional techniques.The integration of nanomaterials and 3D printing technologies allows the fabrication of multiscale functional architectures.Our study reports a unique method of controlled 3D assembly purely relying on the post-printing treatment of printed constructs.By immersing a 3D-printed patterned construct consisting of organic ligand in a solution of lanthanide ions,in situ growth of lanthanide metal-organic frameworks(LnMOFs)can rapidly occur,resulting in macroscopic assemblies and tunable fluorescence properties.This phenomenon,caused by coordination and chelation of lanthanide ions,also renders a sub-millimeter resolution and high shape fidelity.As a proof of concept,a type of 3D assembled LnMOFsbased optical sensing platform has demonstrated the feasibility in response to small molecules such as acetone.It is anticipated that the facile printing and design approach developed in this work can be applied to fabricate bespoke multiscale architectures of functional materials with controlled assembly,bringing a realistic and economic prospect.

HYDRODYNAMIC AND THERMODYNAMIC EFFECTS IN PHASE INVERSION EMULSIFICATION PROCESS OF EPOXY RESIN IN WATER

The mechanism of phase inversion emulsification process （PIE） was studied for waterborne dispersion of highly viscous epoxy resin using non-ionic polymeric surfactants. Drop deformation and breakup, rheological properties, conductivity, and particle size measurements reveal the micro-structural transition amid emulsification. It is revealed that strong flow causes water drop to burst with the formation of droplets and huge interface. Phase inversion corresponds to an abrupt rheological transition from a type of viscous melt with weak elasticity to a highly elastic type of aqueous gel. This implies that the phase inversion equivalent to a curvature inversion. Based on this, a geometric model is postulated to correlate process variables to the particle size. The coverage and conformation of the surfactant plays key role for the particle size of the final emulsion. The interactions of thermodynamic and hydrodynamic effects are also discussed. It is concluded that the thermodynamics control the PIE while the hydrodynamics drives the creation of interface and involves every step of PIE.

USING TWO-DIMENSIONAL TIME RESOLVED LIGHT SCATTERING TO STUDY THE CURE REACTION INDUCED PHASE SEPARATION PROCESS OF EPOXY-AMINE-POLYETHERSULFONE BLEND WITH SECONDARY PHASE SEPARATION

The generalized two-dimensional correlation analysis based on time-resolved light scattering patterns （2D TRLS） has been employed to study the phase separation process of an epoxy-amine-polyethersulfone blend in which the secondary phase separation takes place. The results of the 2D TRLS provided more detailed information that was not readily observed in the 1D TRLS patterns. （i） During the first process of phase separation, the sequential order of coarsening in size of the domains among the larger and smaller ones has been reversed between the diffusion regime and the hydrodynamic regime. （ii） The change of the larger domains in size, due to the hydrodynamic flow in the late stage of the first phase separation process, keeps on taking place earlier than that of the new domains appeared in the secondary phase separation process. （iii） During the secondary phase separation process the size growth of the smaller domains takes place earlier than that of the larger ones, probably due to the assumption that the coarsening mode could decrease the interface tension more quickly.

Morphology and crystal-plane effects of Zr-doped CeO2 nanocrystals on the epoxidation of styrene with tert-butylhydroperoxide as the oxidant

The morphology effect of Zr-doped CeOwas studied in terms of their activities in the selective oxidation of styrene to styrene oxide using tert-butyl hydroperoxide as the oxidant. In the present work, Zrdoped CeOnanorods exhibited the highest catalytic performance（yield of styrene oxide and TOF value）followed by nanoparticles and nanocubes. For the Zr-doped CeOnanorods, the apparent activation energy is 56.3 k J/mol, which is much lower than the values of catalysts supported on nanoparticles and nanocubes（73.3 and 93.4 k J/mol）. The high resolution transmission electron microscopy results indicated that（100） and（110） crystal planes are predominantly exposed for Zr-doped CeOnanorods while（100）and（111） for nanocubes,（111） for nanoparticles. The remarkably increased catalytic activity of the Zrdoped CeOnanorods is mainly attributed to the higher percentage of Cespecies and more oxygen vacancies, which are associated with their exposed（100） and（110） crystal planes. Furthermore, recycling studies proved that the heterogeneous Zr-doped CeOnanorods did not lose its initial high catalytic activity after five successive recycles.

In situ AFM investigation of dual-mode self-assembling peptide

Nanostructures/patterns formed by biomolecules can produce different physicochemical properties in terms of hydrophobicity, zeta-potential, color, etc., which play paramount roles in life. Peptides, as the main bio-building blocks, can form nanostructures with different functions,either in solutions or on interfaces. Previously, we synthesized a short peptide with the inspiration of an Alzheimer’s disease-related peptide: amyloid β peptide(A-p),namely GAV-9, which can epitaxially self-assemble into regular nanofilaments on liquid-solid interfaces, and it was found that both the hydrophobicity and charge state of the interfaces can significantly influence its assembling behavior. It was also reported that another A-β-containing dipeptide, FF,can self-assemble into nanostructures in solutions. Owing to the close relationship between these two short peptides, it is interesting to conjugate them into a de novo peptide with two separated structural domains and study its self-assembling behavior. To this end, herein we have synthesized the GAV-FF peptide with a sequence of NH2-VGGAVVAGVFF-CONH2 and verified its selfassembling property using the in situ liquid-phase atomic force microscopy. The results show that the GAV-FF peptide can self-assemble into nanofilaments both in solutions and on aqueous-solid interfaces, but with different morphologies. The FF domain accelerates the template-assisted self-assembling(TASA) process of the GAV domain, which in return enhances the solubility of FF in aqueous solutions and further participates in the fibrillization of FF. The current results could help deepen the understanding of the aggregation mechanism of diseaserelated peptides and could also shed light on the strategies to create artificial bio-functional nanostructures/patterns,which hold a significant potential for biomedical applications.

THE ROLES OF REACTION INHOMOGENEITY IN PHASE SEPARATION KINETICS AND MORPHOLOGY OF REACTIVE POLYMER BLENDS

The roles of reaction inhomogeneity in phase separation of polymer mixtures were described and summarized via two examples:photocross-link of polymer mixtures in the bulk state and photopolymerization of monomer in the liquid state. The reaction kinetics,the reaction-induced elastic strain and the phase separation kinetics were monitored respectively by UV-Vis spectroscopy,Mach-Zehnder interferometry and laser-scanning confocal microscopy.It was found that phase separation in the bulk state was strongly inf...

PREPARATION OF EVOH MICROPOROUS MEMBRANES via THERMALLY INDUCED PHASE SEPARATION USING BINARY SOLVENTS

Microporous ethylene-vinyl alcohol copolymer （EVOH） flat membranes and hollow-fiber membranes with 38 mol% ethylene content were prepared via thermally induced phase separation （TIPS） using the mixture of 1,4-butanediol and poly（ethylene glycol）（PEG400） as diluents. Effects of the ratio of 1,4-butanediol to PEG400 on the phase diagrams, phase separation mechanism and membrane morphology were studied by small angle light scattering （SALS） measurements, differential scanning calorimetry （DSC）, and scanning ele~：tron microscopy （SEM）. It was found that by varying the composition of the binary solvent, the phase diagrams and membrane morphology can be controlled successfully. Moreover, the phase diagrams showed that broader regions of Liquid-Liquid （L-L） phase separation were obtained, as well as closer distances between L-L phase separation lines and Solid-Liquid （S-L） phase separation lines, Interconnected structures observed both in the flat membrane and hollow fiber membrane consist with the above results.

Fabrication of grating-like polystyrene latex monolayer structure as three-dimensional calibration standards for scanning probe microscope

This paper illuminates the preparation of grating-like polystyrene latex monolayer structure, which can minimize the effects of the size deviation of spheres and the defect transfer on the accuracy as calibration samples for micro-scopes. The latex films are grown on freshly cleaved mica substrates by vertical deposition method. The concentration dependence of the structure and the topography of latex films is characterized by optical microscope, ultraviolet- visible transmission spectrum and scanning probe microscope. The origination of such a grating-like structure is also discussed.

Depletion interactions in binary mixtures of repulsive colloids

Acceptance ratio method, which has been used to calculate the depletion potential in binary hard-sphere mixtures, is extended to the computation of the depletion potential of non-rigid particle systems. The repulsive part of the Lennard-Jones pair potential is used as the direct pair potential between the non-rigid particles. The depletion potential between two big spheres immersed in a suspension of small spheres is determined with the acceptance ratio method through the application of Monte Carlo simulation. In order to check the validity of this method, our results are compared with those obtained by the Asakura-Oosawa approximation, and by Varial expansion approach, and by molecular dynamics simulation. The total effective potential and the depth of its potential well are computed for various softness parameters of the direct pair potential.

Effects of Processing Parameters on Mechanical Properties and Structure of Banana Fiber-Reinforced Composites

The mechanical properties of unidirectional natural fiber-reinforced composites are generally affected by several processing parameters during compression molding.This study investigates the effects of processing temperature,time,and pressure on the tensile and flexural properties of acrylonitrile butadiene styrene reinforced by banana fibers.X-ray CT imaging was employed to find the relationship between the mechanical properties and structure of the processed composite.Besides,the water absorption of composites was observed and the way in which the mechanical properties evolved after water absorption was analyzed.The tensile and flexural properties of the unidirectional banana fiber-reinforced composite were found to be inversely proportional to the porosity.In addition,high-pressure compression molding might result in cracks and floating fibers that would significantly reduce its mechanical properties.The composite with the highest strength,smallest porosity and lowest water absorption was optimally prepared at T=170℃,t=20 min,and P=100 kg cm^-2.