The effect of temperature on load partitioning evolution in magnesium metal matrix composite reinforced with Ti particles using in-situ synchrotron radiation diffraction experiments

The load partitioning between the magnesium and titanium phases in an extruded Mg-15%Ti(vol.%) composite from room temperature up to 300 ℃ using synchrotron radiation diffraction during in-situ compression tests. During compression, the magnesium matrix composite deforms mainly by the activation of the extension twinning system up to 200 ℃. The volume fraction of twins increases with the plastic strain but decrease with the compression temperature. Hard titanium particles bear an additional load transferred by the soft magnesium matrix from room temperature up to 300 ℃. This effect is amplified after yield stress during plastic deformation. Additionally, twins within magnesium grains behaves as an additional reinforcement at low temperature(below 200 ℃) inducing an increase in the work hardening of the composite.

High temperature mechanical behaviour of Mg-6Zn-1Y alloy with 1 wt.% calcium addition:Reinforcing effect due to I-(Mg3Zn6Yi)and Mg6Zn3Ca2 phases

The infiuence of small calcium additions on the high-temperature mechanical behaviour in an extruded Mg-6Zn-l Y(wt.%)alloy reinforced by the I-phase has been investigated.Calcium promotes the formation of the intermetallic Mg6Zn3Ca2 phase instead of 1-phase,which results in a noticeable improvement of the yield strength and ultimate tensile strength of the alloy above 100℃.The strength of the alloys was analysed taking into account the contribution due to the grain size,the crystallographic texture and the volume fraction and nature of second phase particles.In situ synchrotron radiation diffraction experiments have been used to evaluate the load partitioning between the magnesium matrix and the second phase particles(1-and MgeZgCa?phases)in both alloys.The load transfer from the magnesium matrix towards the MgeZihCa?phase is markedly more effective than that for the I-phase over the entire temperature range,especially at 200°C,temperature at which the reinforcement effect of the I-phase is null.

Effect of Cu addition on microstructural evolution and hardening of mechanically alloyed Al-Ti-O in-situ composite

The microstructure formation and strengthening of an Al-5 wt.%TiO2 composites with additions of 5 wt.%Cu and 2 wt.% stearic acid(as a process control agent, PCA) during mechanical alloying and subsequent thermal exposure were studied. The powder composites were prepared by high-energy ball milling for up to 10 h. Single line tracks of the powders were laser melted. Optical and scanning electron microscopy, XRD analysis and differential scanning calorimetry were used to study microstructural evolution. The results showed that the Cu addition promotes an effective mechanical alloying of aluminum with Ti O2 from the start of milling, resulting in higher microhardness(up to HV 290), while the PCA, on the contrary, postpones this process. In both cases, the composite granules with uniform distribution of Ti O2 particles were formed. Subsequent heating of mechanically alloyed materials causes the activation of an exothermic reaction of Ti O2 reduction with aluminum, the start temperature of which, in the case of Cu addition,shifts to lower values, that is, the transformation begins in the solid state. Besides, the Cu-added material after laser melting demonstrates a more dispersed and uniform structure which positively affects its microhardness.

Thermo-Mechanical Influence on the Internal Friction of a 51CrV4 Shaft

The influence of simultaneously applied mechanical and thermal treatment is used for producing a geometrically complex shaft from 51CrV4 steel resulting in widely differing formations of microstructures.Materials'properties such as internal friction(IF),hardness and electrical resistivity are affected by this change of microstructure formations.The Snoek–Koster peak is identified and analyzed in the actual steel structure.

Effect of sintering temperature on structure and tribological properties of nanostructured Ti-15Mo alloy for biomedical applications

The effect of sintering temperature(1073?1373 K)on the structural and tribological properties of nanostructured ballmilledβ-type Ti?15Mo samples was investigated.The prepared samples were characterized using various apperatus such as X-ray diffractometer,scanning electron microscope(SEM)and ball-on-plate type oscillating tribometer.Wear tests were conducted under different applied loads(2,8 and 16 N).Structural results showed that the mean pore and crystallite size continuously decreased with increasing sintering temperature to reach the lowest values of 4 nm and 29 nm at 1373 K,respectively.The relative density of the sintered sample at 1373 K was as high as 97.0%.Moreover,a higher sintering temperature resulted in higher relative density,greater hardness and elastic modulus of the sample.It was observed that both the friction coefficient and wear rate were lower in the sample sintered at 1373 K which was attributed to the closed porosity.

Structure-function integrated magnesium alloys and their composites

Magnesium-based materials not only exhibit desirable characteristics such as low density and high specific strength, but also possess exceptional functional properties, including high damping capacity, high thermal conductivity, high electromagnetic interference shielding capacity, flame retardancy, and dissolvability. However, achieving a balance between strength and functional properties remains a significant challenge in Mg alloys community. Typically, strength depends on the pinning effect of defects, such as solute atoms and second phases,which hinder dislocation motion. On the other hand, optimal functional properties usually necessitate relative perfect crystal structures, as the presence of solute atoms and second phases can have adverse effects on damping capacity and thermal conductivity. Balancing these conflicting requirements is difficult. The trade-off between strength and functional properties of the Mg alloys should be broken to meet the urgent need in aerospace, automotive, 3C(computers, communications, and consumer electronics) and energy industries for high performance structural-functional integrated Mg-based materials. This review summarizes recent progress in understanding the mechanisms and influencing factors for the functional properties of Mg alloys. The mechanisms underlying the trade-off between strength and functional properties of Mg alloys is discussed. The latest developed structural-functional integrated Mg alloys and their composites are summarized, including high strength Mg-based materials with high damping capacity/high thermal conductivity/strong electromagnetic shielding capability/excellent flame-resistance/high dissolution rate. The future works of developing structure-function integrated Mg-based materials are proposed.

The relation between ductility at high temperature and solid solution in Mg alloys

This work investigates the effect of solid solution on ductility and on the activation of individual deformation mechanisms at moderate temperatures and at quasi-static strain rates in Mg-Zn and Mg-Al alloys. With that aim, four solid solution Mg-Zn and Mg-Al binary alloy ingots containing 1 and 2 wt.% solute atoms were subjected to hot rolling and subsequent annealing to generate polycrystals with similar average grain size and basal-type texture for each composition. The activity of the different slip systems after tensile testing at 150°C and at 250°C was evaluated in pure Mg and in the alloys by EBSD-assisted slip trace analysis. In addition, segregation of Zn and Al atoms at grain boundaries during the thermo-mechanical processing was characterized by HAADF-STEM and EDX. It was found that while the addition of Al and Zn atoms to pure Mg does not lead to major changes in the mechanical strength at the investigated temperatures, it does enhance ductility significantly, especially at 250℃. Our results show that this increase in ductility cannot be attributed to a higher activation of non-basal systems in the alloys, as reported earlier, as the incidence of non-basal systems is indeed considerably higher in pure Mg. This work suggests, on the contrary, that the ductility increase may be attributed to the presence of a more homogenous basal activity in the alloys due to a lower degree of orientation clustering, to grain boundary solute segregation, and to a higher slip diffusivity at grain interiors.

Influence of V(C,N) Precipitates on Microstructure and Mechanical Properties of Continuous Cooled C-Mn-V

The effect of chemical composition and processing parameters on the formation of acicular ferrite and/or bainite has been investigated.In particular,this paper deals with the influence that N through its combination with V,as V(C,N) precipitates,has on the decomposition of austenite.Likewise,the intragranular nucleation potency of V(C,N) precipitates is analyzed through the continuous cooling transformation diagrams (CCT) of two C-Mn-V steels with different contents of N.Results reported in this work allow us to conclude that acicular ferrite can only be achieved alloying with vanadium and nitrogen,meanwhile bainite is promoted in steels with a low level of nitrogen.It is concluded that higher strength values are obtained in acicular ferrite than in bainitic steel but a similar brittle-ductile transition temperature (BDT),and lower values of impact absorbed energy (KV) has been recorded in nitrogen-rich steel.

Influence of the Accumulative Roll Bonding Process Severity on the Microstructure and Superplastic Behaviour of 7075 Al Alloy

The 7075 Al alloy was processed by accumulative roll bonding （ARB） at 350 ℃ using 2：1, 3：1 and 4：1 thickness reductions per pass （Rp） up to 8, 6 and 3 passes, respectively. Microstructural examinations of the processed samples revealed that ARB leads to a microstructure composed of equiaxed crystallites with a mean size generally lower than 500 nm. It was found that, due to both the stored energy through- out the processing and the particle pinning effect, the alloy is affected by discontinuous recrystallisation during the inter-pass heating stages, the precise microstructural evolution being dependent on Rp. Me- chanical testing of the ARBed samples revealed that the main active deformation mechanism in the ARBed samples in the temperature range from 250 to 350 ℃ at intermediate and high strain rates is grain bound- ary sliding, the superplastic properties being determined by both the microstructure after ARB and its thermal stability.

Effect of rhenium on the microstructure and mechanical behavior of Fe–2.25Cr–1.6W–0.25V-0.1C bainitic steels

A new ferritic creep resistant steel has been developed by eliminating Nb and adding 1.5 mass % Re to a ferritic steel grade T/P23 with the aim of enhancing its mechanical properties at high temperature.Cast ingots of both steels, new grade and ASTM T/P 23, were hot rolled at 900℃ and then submitted to a thermal treatment consisting of solubilization at 1050℃ and tempering at 700℃. Tempered bainitic microstructures obtained contain second phases reinforcing carbide particles, mainly M_6C and M_（23）C_6 at the boundaries of both, prior austenite grains and bainitic ferrite laths, as well as MC within the grains. Mechanical properties at temperatures ranging from 540 to 600℃ were studied by strain-ratechange tests in compression at strain rates between 10^（-7） and 10^（-4）s^（-1）. These tests showed high stress exponents（n ≥ 20） and activation energies（Q ≈ 400 k J/mol） for both alloys, which were associated with a dislocation movement mechanism with a strong interaction between dislocations and precipitates. On the other hand, a creep exponent of 5 was derived for the stress dependence of minimum creep rate from conventional-type creep tests at 600℃. Although this stress exponent is usually related to a dislocation climb controlled creep mechanism, remarkable microstructural degradation observed with increasing creep time makes difficult to elucidate the true deformation mechanism controlling creep.

Warm Forged Medium Carbon V Steel

Nowadays there is a continuous demand,particularly from the automotive industry,for cheaper,lighter and more reliable components.It is not surprising then that steel research has been focused during the last decades in new qualities and processes.This paper is dealing with the use of vanadium microalloyed steels on one of those new processes,warm forging.For its low precipitation temperature and its recognised ability to strengthen steel microstructures via austenite grain growth control,precipitation hardening and interference of the static recrystallization process,vanadium in microalloyed steels seem to be an appropriate candidate for warm forging.