The static flux chamber method was applied to study natural emissions of methane to the atmosphere in the Luntai fault region of Yakela Condensed Oil/Gas Field in the Tarim Basin, Xinjiang Municipality, northwestern C...The static flux chamber method was applied to study natural emissions of methane to the atmosphere in the Luntai fault region of Yakela Condensed Oil/Gas Field in the Tarim Basin, Xinjiang Municipality, northwestern China. Using an online method, which couples together a gas chromatography/high-temperature conversion/isotope ratio mass spectrometry （GC/C/MS）, 13^C/12^C ratios of methane in flux chambers were measured and showed that methane gases are liable to migrate from deep oil/gas reservoirs to the surface through fault regions and that a part of the migrated methane, which remains unoxidized can be emitted into the atmosphere. Methane emission rates were found to be highest in the mornings, lowest in the afternoons and then increase gradually in the evenings. Methane emission rates varied dramatically in different locations in the fault region. The highest methane emission rate was 10.96 mg/m^2·d, the lowest 4.38 mg/m^2, and the average 7.55 mg/ m^2·d. The 13^C/12^C ratios of the methane in the flux chambers became heavier as the enclosed methane concentrations increased gradually, which reveals that methane released from the fault region might come from thermogenic methane of the deep condensed oil/gas reservoir.展开更多
The electrochemical method was used to remove nickel ion from spent electroless nickel plating bath (pH=5 3). An electrolytic cell was composed of a porous nickel foam cathode and an inert RuO 2/Ti anode. Nickel ions ...The electrochemical method was used to remove nickel ion from spent electroless nickel plating bath (pH=5 3). An electrolytic cell was composed of a porous nickel foam cathode and an inert RuO 2/Ti anode. Nickel ions were reduced and deposited on the surface of the nickel foam cathode. The effect of current density (i), linear velocity of wastewater(v), gap between cathode and anode(d C/A) and reaction time(t) on nickel removal rate and current efficiency were studied. As reaction time prolonged, nickel removal rate increased while current efficiency decreased. And larger v and smaller d C/A can enhance nickel removal rate and increase current efficiency by promoting mass transfer and dropping concentration polarization. The effect of current density on nickel removal by electrochemistry was related to other parameters. After three hours’ electrolysis with i=1 0 A/dm2, v=18 5 cm/min and d C/A=0 5 cm, nickel removal rate and current efficiency reached 85 6% and 29 1%, respectively.展开更多
基金This study was supported by the Natural Science Foundation of China （grant No. 40273034）the Science Foundation of Hongzhou Danzi University.
文摘The static flux chamber method was applied to study natural emissions of methane to the atmosphere in the Luntai fault region of Yakela Condensed Oil/Gas Field in the Tarim Basin, Xinjiang Municipality, northwestern China. Using an online method, which couples together a gas chromatography/high-temperature conversion/isotope ratio mass spectrometry （GC/C/MS）, 13^C/12^C ratios of methane in flux chambers were measured and showed that methane gases are liable to migrate from deep oil/gas reservoirs to the surface through fault regions and that a part of the migrated methane, which remains unoxidized can be emitted into the atmosphere. Methane emission rates were found to be highest in the mornings, lowest in the afternoons and then increase gradually in the evenings. Methane emission rates varied dramatically in different locations in the fault region. The highest methane emission rate was 10.96 mg/m^2·d, the lowest 4.38 mg/m^2, and the average 7.55 mg/ m^2·d. The 13^C/12^C ratios of the methane in the flux chambers became heavier as the enclosed methane concentrations increased gradually, which reveals that methane released from the fault region might come from thermogenic methane of the deep condensed oil/gas reservoir.
文摘The electrochemical method was used to remove nickel ion from spent electroless nickel plating bath (pH=5 3). An electrolytic cell was composed of a porous nickel foam cathode and an inert RuO 2/Ti anode. Nickel ions were reduced and deposited on the surface of the nickel foam cathode. The effect of current density (i), linear velocity of wastewater(v), gap between cathode and anode(d C/A) and reaction time(t) on nickel removal rate and current efficiency were studied. As reaction time prolonged, nickel removal rate increased while current efficiency decreased. And larger v and smaller d C/A can enhance nickel removal rate and increase current efficiency by promoting mass transfer and dropping concentration polarization. The effect of current density on nickel removal by electrochemistry was related to other parameters. After three hours’ electrolysis with i=1 0 A/dm2, v=18 5 cm/min and d C/A=0 5 cm, nickel removal rate and current efficiency reached 85 6% and 29 1%, respectively.
