Review on friction stir welding of dissimilar magnesium and aluminum alloys: Scientometric analysis and strategies for achieving high-quality joints

Magnesium and aluminum alloys continually attract interest as lightweight structural materials for transport applications. However, joining these dissimilar alloys is very challenging. The main obstacle that hinders progress in dissimilar Mg-Al joining is the formation of brittle intermetallic compounds(IMCs). As a solid-state joining technique, FSW is an excellent candidate to attenuate the deleterious IMC effects in dissimilar Al-Mg joining due to the inherent low heat inputs involved in the process. However, the IMCs, namely Al_(3)Mg_(2) and Al_(12)Mg_(17) phases, have also been reported to form during Al-Mg dissimilar FSW;their amount and thickness depend on the heat input involved;thus,the weld parameters used. Since the heat dissipated in the material during the welding process significantly affects the amount of IMCs,the heat input during FSW should be kept as low as possible to control and reduce the amount of IMCs. This review aims to critically discuss and evaluate the studies conducted in the dissimilar Al/Mg FSW through a scientometric analysis and also with a focus on the strategies recently applied to enhance joint quality. The scientometric analysis showed that the main research directions in Mg/Al FSW are the technological weldability of aluminum and magnesium during FSW, structural morphology, and mechanical properties of dissimilar welded joints. Considering the scope of application of the aforementioned joints, the low share of articles dealing with environmental degradation and operational cracking is surprising. This might be attributed to the need for well-developed strategies for obtaining high-quality and sustainable joints for applications. Thus, the second part of this review is conventional, focusing mainly on the new strategies for obtaining high-quality Mg/Al joints. It can be concluded that in addition to the necessity to optimum welding parameters to suppress the excessive heat to limit the amount and thickness of IMC formed and improve the overall joint quality, strategies such as using Zn interlayer, electric current assisted FSW(EAFSW), ultrasonic vibration FSW(UVa FSW), are considered effective in the elimination, reduction, and fragmentation of the brittle IMCs.

一种用于船舶汽轮机的安全且经济的启动加速概念

This paper analyses the issue of accelerated start-up of a marine steam turbine,which is an important problem because the start-up of a steam machine involves the combustion of fuel that is not transformed into useful energy.To find novel technologies that offer improvements in this aspect is essential due to restrictions on reducing ship emissions.Thus,the shorter the start-up time,the better for the environment and economy.High-pressure(HP)part of the turbine originally located on the Queen Elizabeth II unit was analysed.Advanced numerical calculations by thermal fluid-solid-interaction(Thermal FSI)were carried out.A series of simulations were performed for the accelerated start-up with controlled steam injection.A description of the chosen calculation methodology and the results obtained by simulation are included in this paper.The stress occurring during the accelerated start-up are approximately 40 MPa higher than those during the reference start-up.The relative elongations between the rotor and the hull during accelerated start-up reach a maximum value of 0.89 mm(0.83 mm for ultra-fast start-up).Reducing the steam turbine start-up time by 75%results in a 36.7 tons reduction in fuel consumption for start-up,resulting in an annual savings of 5372 USD.In conclusion,the concept proposed by the authors is safe,less expensive and does not affect the life of the turbine.In addition,results and applications from Siemens prove that additional injection of cooling steam is possible.

Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction

In hydrodynamic bearings traditional bearing alloys:Babbitts and bronzes are most frequently utilized.Polymer sliding layers are sometimes applied as a valuable alternative.Hard diamond-like carbon(DLC)coatings,which are also considered for certain applications may show some advantages,as well.Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction conditions,which is crucial for bearings with frequent starts and stops.Experimental research aimed at studying the performance of fluid film bearings in the specific operating regime,including the transition to mixed friction,is described in the paper.The tests were carried out on four tilting pad bearings of different material compositions:Steel/bronze,DLC/steel,steel/polyether ether ketone(PEEK),and steel/Babbitt.The tests comprised stopping under load and reproduction of the Stribeck curve by decreasing rotational speed to very low values,and observing the changes of friction force during the transition to mixed friction regime.Analysis of the transition conditions and other results showed clear differences between the tested bearings,illustrating the feasibility of less popular material compositions for bearings operating in specific conditions.More specifically,the DLC/steel bearing was demonstrating superior performance,i.e.lower friction,transition to mixed friction occurring at higher load,and more stable performance at start-stop regime over the other tested bearings.