A Review on Vibration Control of Multiple Cylinders Subjected to FlowInduced Vibrations

The fatigue damage caused by flow-induced vibration(FIV)is one of the major concerns for multiple cylindrical structures in many engineering applications.The FIV suppression is of great importance for the security of many cylindrical structures.Many active and passive control methods have been employed for the vibration suppression of an isolated cylinder undergoing vortex-induced vibrations(VIV).The FIV suppression methods are mainly extended to the multiple cylinders from the vibration control of the isolated cylinder.Due to the mutual interference between the multiple cylinders,the FIV mechanism is more complex than the VIV mechanism,which makes a great challenge for the FIV suppression.Some efforts have been devoted to vibration suppression of multiple cylinder systems undergoing FIV over the past two decades.The control methods,such as helical strakes,splitter plates,control rods and flexible sheets,are not always effective,depending on many influence factors,such as the spacing ratio,the arrangement geometrical shape,the flow velocity and the parameters of the vibration control devices.The FIV response,hydrodynamic features and wake patterns of the multiple cylinders equipped with vibration control devices are reviewed and summarized.The FIV suppression efficiency of the vibration control methods are analyzed and compared considering different influence factors.Further research on the FIV suppression of multiple cylinders is suggested to provide insight for the development of FIV control methods and promote engineering applications of FIV control methods.

Coupling of quasi-localized and phonon modes in glasses at low frequency

Boson peak of glasses,a THz vibrational excess compared to Debye squared-frequency law,remains mysterious in condensed-matter physics and material science.It appears in many different kinds of glassy matters and is also argued to exist in damped crystals.A consensus is that boson peak originates from the coupling of the(quasi)-localized non-phonon modes and the plane-wave-like phonon modes,but the coupling behavior is still not fully understood.In this paper,by modulating the content of localized modes and the frequencies of phonon modes,the coupling is clearly reflected in the localization and anharmonicity of low-frequency vibrational modes.The coupling enhances with increasing cooling rate and sample size.For finite sample size,phonon modes do not fully intrude into the low frequency to form a dense spectrum and they are not sufficiently coupled to the localized modes,thus there is no Debye level and boson peak is ill-defined.This suggestion remains valid in the presence of thermal motions induced by temperature,even though the anharmonicity comes into play.Our results point to the coupling of quasi-localized and phonon modes and its relation to the boson peak.

Parallelization strategies for resolved simulations of fluid-structure-particle interactions

Fluid-structure-particle interactions in three spatial dimensions happen in many environmental and engineering flows.This paper presents the parallel algorithms for the hybrid diffuse and sharp interface immersed boundary(IB)method developed in our previous work.For the moving structure modeled using the sharp interface IB method,a recursive box method is developed for efficiently classifying the background grid nodes.For the particles modeled using the diffuse interface IB method,a‘master-slave’approach is adopted.For the particle-particle interaction(PPI)and particle-structure interaction(PSI),a fast algorithm for classifying the active and inactive Lagrangian points,which discretize the particle surface,is developed for the‘dry’contact approach.The results show that the proposed recursive box method can reduce the classifying time from 52seconds to 0.3 seconds.Acceptable parallel efficiency is obtained for cases with different particle concentrations.Furthermore,the lubrication model is utilized when a particle approaches a wall,enabling an accurate simulation of the rebounding phenomena in the benchmark particle-wall collision problem.At last,the capability of the proposed computational framework is demonstrated by simulating particle-laden turbulent channel flows with rough walls.

Numerical Analysis of Perforation during Hydraulic Fracture Initiation Based on Continuous-Discontinuous Element Method

Perforation is a pivotal technique employed to establish main flow channels within the reservoir formation at the outset of hydraulic fracturing operations.Optimizing perforation designs is critical for augmenting the efficacy of hydraulic fracturing and boosting oil or gas production.In this study,we employ a hybrid finite-discrete element method,known as the continuous–discontinuous element method(CDEM),to simulate the initiation of post-perforation hydraulic fractures and to derive enhanced design parameters.The model incorporates the four most prevalent perforation geometries,as delineated in an engineering technical report.Real-world perforations deviate from the ideal cylindrical shape,exhibiting variable cross-sectional profiles that typically manifest as an initial constriction followed by an expansion,a feature consistent across all four perforation types.Our simulations take into account variations in perforation hole geometries,cross-sectional diameters,and perforation lengths.The findings show that perforations generated by the 39g DP3 HMX perforating bullet yield the lowest breakdown pressure,which inversely correlates with increases in sectional diameter and perforation length.Moreover,this study reveals the relationship between breakdown pressure and fracture degree,providing valuable insights for engineers and designers to refine perforation strategies.

Protective performance of shear stiffening gel-modified foam against ballistic impact:Experimental and numerical study

As one of the most widely used personal protective equipment(PPE),body armors play an important role in protecting the human body from the high-velocity impact of bullets or projectiles.The body torso and critical organs of the wear may suffer severe behind-armor blunt trauma(BABT)even though the impactor is stopped by the body armor.A type of novel composite material through incorporating shear stiffening gel(STG)into ethylene-vinyl acetate(EVA)foam is developed and used as buffer layers to reduce BABT.In this paper,the protective performance of body armors composed of fabric bulletproof layers and a buffer layer made of foam material is investigated both experimentally and numerically.The effectiveness of STG-modified EVA in damage relief is verified by ballistic tests.In parallel with the experimental study,numerical simulations are conducted by LS-DYNA®to investigate the dynamic response of each component and capture the key mechanical parameters,which are hardly obtained from field tests.To fully describe the material behavior under the transient impact,the selected constitutive models take the failure and strain rate effect into consideration.A good agreement between the experimental observations and numerical results is achieved to prove the validity of the modelling method.The tests and simulations show that the impact-induced deformation on the human body is significantly reduced by using STG-modified EVA as the buffering material.The improvement of protective performance is attributed to better dynamic properties and more outstanding energy absorption capability of the composite foam.

Analytical solutions of turbulent boundary layer beneath forward-leaning waves

As a typical nonlinear wave,forward-leaning waves can be frequently encountered in the near-shore areas,which can impact coastal sediment transport significantly.Hence,it is of significance to describe the characteristics of the boundary layer beneath forward-leaning waves accurately,especially for the turbulent boundary layer.In this work,the linearized turbulent boundary layer model with a linear turbulent viscosity coefficient is applied,and the novel expression of the near-bed orbital velocity that has been worked out by the authors for forward-leaning waves of arbitrary forward-leaning degrees is further used to specify the free stream boundary condition of the bottom boundary layer.Then,a variable transformation is found so as to make the equation of the turbulent boundary layer model be solved analytically through a modified Bessel function.Consequently,an explicit analytical solution of the turbulent boundary layer beneath forward-leaning waves is derived by means of variable separation and variable transformation.The analytical solutions of the velocity profile and bottom shear stress of the turbulent boundary layer beneath forward-leaning waves are verified by comparing the present analytical results with typical experimental data available in the previous literature.

The effect of gravity on self-similarity of Worthington jet after water entry of a two-dimensional wedge

The effect of gravity on the self-similarity of jet shape at late stage of Worthington jet development is investigated by experiment in the study.In addition,the particle image velocimetry(PIV)method is introduced to analyze the development of flow field.There is a linear scaling regarding the axial velocity of the jet and the scaling coefficient increases with the Froude number.

Estimating energy release performance of oxidizer-activated aluminum fuel particles under ultrafast stimulus

Aluminum(Al) particles are good fuel additives to improve the energy output performances of explosives. Under detonation environment, reaction delay of Al particles plays a key role in the energy release efficiency. Up to date, reaction delay of Al particles is still limited by the efficiency of mass and heat transfer from oxidizers to Al particles. To address this issue, a homogeneous fuel-oxidizer assembly has recently become a promising strategy. In this work, oxidizer-activated Al fuel particles(ALG) were prepared with glycidyl azide polymer(GAP) as the oxidizer. The ALG was in uniform spherical shape and core-shell structure with shell layer of around 5 nm which was observed by scanning electron microscope and transmission electron microscope. The localized nanoscale mid-IR measurement detected the uniform distribution of characteristic absorption bond of GAP in the shell layer which confirmed the homogenous fuel-oxidizer structure of ALG. A thermal gravimetric analysis of ALG at ultrafast heating rate of 1000℃/min under argon atmosphere was conducted. The decomposition of GAP finished much earlier than that of GAP at heating rate of 10℃/min. Under ultrafast high laser fluence, the reaction response of ALG was characterized and compared with that of micro-sized Al(μAl). With the increase of laser energy, the propagation distance of the shock wave increased. However, the velocity histories were nearly the same when energies were lower than 299 mJ or higher than 706 mJ. The propagation distance of the shock wave for ALG was 0.5 mm larger than that for μAl at 2.1 μs. The underwater explosion showed the peak pressure and the shock wave energy of the ALG-based explosive were both higher than those of the μAl-based explosive at 2.5 m. This study shows the feasibility to improve the energy release of Al-based explosives via using the oxidizer-activated Al fuel particles with energetic polymer as the oxidizer.

Effect of Pouring Temperature by a Novel Micro Fused-Casting on Microstructure and Properties of ZL101 Semisolid Slurry

A novel micro fused-casting(MFC)process is developed for semisolid aluminum alloy slurry.The microstructure evolution and properties of semisolid ZL101 aluminum alloy slurry with difierent pouring temperature by MFC are investigated in this paper.During the cooling process,the effects of the pouring temperature on microstructure and properties is primarily analyzed.The microstructure of the semisolid ZL101 aluminum alloy is more homogeneous and the grain is smaller under proper pouring temperature.Temperature of liquids and solids of ZL101 aluminum alloy is measured by difierential scanning calorimetry(DSC).Distribution and characteristics of the microstructure of samples are examined by optical microscope(OM),scanning electron microscopy(SEM)equipped with energy dispersive spectrometer(EDS).The results show that the ZL101 semisolid slurry fabricated by MFC presents uniform shape and good grain size under the pouring temperature of 594°C and the stirring velocity of 600 r/min,and the fine grains of the primary a-Al phase with average grain size of 55μm and shape factor up to 0.67 were obtained.Besides,the ultimate tensile strength and the average Vickers hardness for semisolid ZL101 aluminum slurry are 178.19±1.37 MPa and 86.15±1.16 HV,respectively.

Continuous-discontinuous element method for three-dimensional thermal cracking of rocks

Thermal cracking of rocks can significantly affect the durability of underground structures in engineering practices such as geothermal energy extraction,storage of nuclear waste and tunnelling in freezeethaw cycle induced areas.It is a scenario of strong coupled thermomechanical process involving discontinuity behaviours of rocks.In this context,a numerical model was proposed to investigate the thermal cracking of rocks,in a framework of the continuous-discontinuous element method(CDEM)for efficiently capturing the initiation and propagation of multiple cracks.A simplex integration strategy was adopted to account for the influences of temperature-dependent material properties.Several benchmark tests were considered and the obtained results were compared with analytical solutions and numerical results from the literature.The results show that the fracture degree of the cases when considering temperature-dependent material parameters had 10%differences approximately compared with the cases with constant parameters.

Relations of Microstructural Attributes and Strength-Ductility of Zirconium Alloys with Hydrides

As the first safety barrier of nuclear reactors,zirconium alloy cladding tubes have attracted extensive attention because of its good mechanical properties.The strength and ductility of zirconium alloy are of great significance to the service process of cladding tubes,while brittle hydrides precipitate and thus deteriorate the overall performance.Based on the cohesive finite element method,the effects of cohesive strength,interfacial characteristics,and hydrides geometric characteristics on the strength and ductility of two-phase material(zirconium alloy with hydrides)are numerically simulated.The results show that the fracture behavior is significantly affected by the cohesive strength and that the overall strength and ductility are sensitive to the cohesive strength of the zirconium alloy.Furthermore,the interface is revealed to have prominent effects on the overall fracture behavior.When the cohesive strength and fracture energy of the interface are higher than those of the hydride phase,fracture initiates in the hydrides,which is consistent with the experimental phenomena.In addition,it is found that the number density and arrangement of hydrides play important roles in the overall strength and ductility.Our simulation provides theoretical support for the performance analysis of hydrogenated zirconium alloys during nuclear reactor operation.

Linear analysis of the dynamic response of a riser subject to internal solitary waves

The flow field induced by internal solitary waves(ISWs)is peculiar wherein water motion occurs in the whole water depth,and the strong shear near the pycnocline can be generated due to the opposite flow direction between the upper and lower layers,which is a potential threat to marine risers.In this paper,the flow field of ISWs is obtained with the Korteweg-de Vries(Kd V)equation for a two-layer fluid system.Then,a linear analysis is performed for the dynamic response of a riser with its two ends simply supported under the action of ISWs.The explicit expressions of the deflection and the moment of the riser are deduced based on the modal superposition method.The applicable conditions of the theoretical expressions are discussed.Through comparisons with the finite element simulations for nonlinear dynamic responses,it is proved that the theoretical expressions can roughly reveal the nonlinear dynamic response of risers under ISWs when the approximation for the linear analysis is relaxed to some extent.

Recent advances in theoretical models of respiratory mechanics

As an important branch of biomedical engineering, respiratory mechanics helps to understand the physiology of the respiratory system and provides fundamental data for developing such clinical technologies as ventilators. To solve different clinical problems, researchers have developed numerous models at various scales that describe biological and mechanical properties of the respiratory system. During the past decade, benefiting from the continuous accumulation of clinical data and the dramatic progress of biomedical technologies （e.g. biomedical imaging）, the theoretical modeling of respiratory mechanics has made remarkable progress regarding the macroscopic properties of the respiratory process, complexities of the respiratory system, gas exchange within the lungs, and the coupling interaction between lung and heart. The present paper reviews the advances in the above fields and proposes potential future projects.

Experimental study of the temporary plugging capability of diverters to block hydraulic fractures in high-temperature geothermal reservoirs

The effective plugging of artificial fractures is key to the success of temporary plugging and diverting fracturing technology,which is one of the most promising ways to improve the heat recovery efficiency of hot dry rock.At present,how temporary plugging agents plug artificial fractures under high temperature remains unclear.In this paper,by establishing an improved experimental system for the evaluation of temporary plugging performance at high temperature,we clarified the effects of high temperature,injection rate,and fracture width on the pressure response and plugging efficiency of the fracture.The results revealed that the temporary plugging process of artificial fractures in hot dry rock can be divided into four main stages:the initial stage of temporary plugging,the bridging stage of the particles,the plugging formation stage,and the high-pressure dense plugging stage.As the temperature increases,the distribution distance of the temporary plugging agent,the number of pressure fluctuations,and the time required for crack plugging increases.Particularly,when the temperature increases by 100℃,the complete plugging time increases by 90.7%.

An overview of fluids mixing in T-shaped mixers

In a T-shaped mixer,the two liquid streams in the inlet channels meet each other at the T-junction,and their liquid-liquid contacting face exhibits planar,swirling folds and the folds breaking to be chaos and turbulence,as the Reynolds number increases.The characteristic mixing scenario attracts long-time attention,given these mixings are of fundamental importance in fluid physics and also have been successfully used in engineering applications.The experimental and numerical studies of flow features and mixing characteristics in T-mixers are overviewed in this manuscript.This review introduces the experimental and numerical techniques in the studies,the flow and mixing characteristics in the corresponding regimes and application examples of the T-mixers at last,aiming at introducing fundamentals to researchers with initial interests on this topic.

Space-time correlations of passive scalar in Kraichnan model

We consider the two-point,two-time(space-time)correlation of passive scalar R(r,τ)in the Kraichnan model under the assumption of homogeneity and isotropy.Using the fine-gird PDF method,we find that R(r,τ)satisfies a diffusion equation with constant diffusion coefficient determined by velocity variance and molecular diffusion.Itssolution can be expressed in terms of the two-point,one time correlation of passive scalar,i.e.,R(r,0).Moreover,the decorrelation o R(k,τ),which is the Fourier transform of R(r,τ),is determined byR(k,0)and a diffusion kernal.

Investigation of radial heat conduction with 1D self-consistent model in helicon plasmas

A 1D radially self-consistent model in helicon plasmas has been established to investigate the influence of radial heat conduction on plasma transport and wave propagation.Two kinds of 1D radial fluid models,with and without considering heat conduction,have been developed to couple the 1D plasma-wave interaction model,and self-consistent solutions have been obtained.It is concluded that in the low magnetic field range the radial heat conduction plays a moderate role in the transport of helicon plasmas and the importance depends on the application of the helicon source.It influences the local energy balance leading to enhancement of the electron temperature in the bulk region and a decrease in plasma density.The power deposition in the plasma is mainly balanced by collisional processes and axial diffusion,whereas it is compensated by heat conduction in the bulk region and consumed near the boundary.The role of radial heat conduction in the large magnetic field regime becomes negligible and the two fluid models show consistency.The local power balance,especially near the wall,is improved when conductive heat is taken into account.

Numerical study of the radio-frequency biased accelerating system in ion thrusters

A 2D-3V implicit immersed-finite-element particle-in-cell(IFE-PIC)model is introduced to investigate the radio-frequency(RF)self-bias accelerating system applied in the RF ion thruster.A set of holes in a two-grid system with slit apertures is simulated in Cartesian coordinates.The characteristics of the plasma plume,such as the ion density,the neutralization rate and the ion and electron current density were investigated for different RF voltage amplitudes(600-1200V)and frequencies(6-30 MHz).Furthermore,the performance of the thruster was also carefully studied.The simulation results show that a well-focused plasma beam can be formed when the voltage amplitude is larger than 900 V and the frequency exceeds the reciprocal of ion transit time(≥12 MHz)in our simulation cases.The performance of the system can be evidently improved by increasing the voltage amplitude and the frequency,and the losses of the particle and thrust are reduced correspondingly.The bulk region of the plasma beam downstream shows good quasi-neutrality,and the ions are dominant in the peripheral region when a well-focused state is achieved.The high ion density beamlet in the periphery of the ion beam is closer to the axis when the voltage amplitude is increasing,while it is expanded radially when increasing the frequency.Backstream electrons have been observed upstream,and this mainly occurs in the phase in which the electron cannot escape.

ANALYSIS AND APPLICATION OF ELLIPTICITY OF STABILITY EQUATIONS ON FLUID MECHANICS

By using characteristic analysis of the linear and nonlinear parabolic stability equations ( PSE), PSE of primitive disturbance variables are proved to be parabolic intotal. By using sub- characteristic analysis of PSE, the linear PSE are proved to be elliptical and hyperbolic-parabolic for velocity U, in subsonic and supersonic, respectively; the nonlinear PSE are proved to be elliptical and hyperbolic-parabolic for relocity U + u in subsonic and supersonic., respectively . The methods are gained that the remained ellipticity is removed from the PSE by characteristic and sub-characteristic theories , the results for the linear PSE are consistent with the known results, and the influence of the Mach number is also given out. At the same time , the methods of removing the remained ellipticity are further obtained from the nonlinear PSE .

Advances of Microgravity Sciences

Advances of microgravity sciences in China are introduced. The research works include ground-based study and space experiments. In the recent years, the main means still are theoretical analysis, numerical simulation, ground-based experiment, and short-time microgravity experiments of drop tower. Besides, many space experiment projects are arranged. SJ-10 recoverable satellite will carry out 19 scientific experiment projects. Nine of them are for microgravity Sciences. The other ways for space microgravity experiment are with the help of Chinese Shenzhou spacecraft, Chinese Tiangong space laboratory, and Chinese space station in the near future. The Chinese space station will become main platform of Chinese microgravity sciences experiment in space.