Seismic performance evaluation of water supply pipes installed in a full-scale RC frame structure based on a shaking table test

As an important part of nonstructural components,the seismic response of indoor water supply pipes deserves much attention.This paper presents shaking table test research on water supply pipes installed in a full-scale reinforced concrete(RC)frame structure.Different material pipes and different methods for penetrating the reinforced concrete floors are combined to evaluate the difference in seismic performance.Floor response spectra and pipe acceleration amplification factors based on test data are discussed and compared with code provisions.A seismic fragility study of displacement demand is conducted based on numerical simulation.The acceleration response and displacement response of different combinations are compared.The results show that the combination of different pipe materials and different passing-through methods can cause obvious differences in the seismic response of indoor riser pipes.

Shaking table test study on performance and functionality of a typical telecommunication room after earthquakes

Large numbers of basic transceiver stations,where the telecommunication room is one of the main components,comprise an important part of the telecommunication system.After earthquakes,considerable economic loss from telecommunication systems is often associated with seismic damage and functional loss of the telecommunication room.However,research related to this has been limited.In this study,shaking table tests were conducted for a full-scale typical telecommunication room,including a light-steel house and the necessary communication and power supply equipment.The tests not only focused on the seismic damage to all the structures but also considered the functions of the communication and power supply of the equipment.The interactions between these facilities and their effects on communication function were also investigated.Compared with the damage to structures,the interruption of the power supply due to earthquakes is a weak link.Finally,the damage indexes,together with their threshold values of different damage states for the communication and power supply equipment,were derived from the test results.The results of this research can contribute to the literature gaps regarding seismic performance studies of telecommunication rooms,and can serve as a valuable reference for future research on its seismic fragility and economic losses evaluation.

Numerical Simulation of the Seismic Response of a Horizontal Storage Tank Based on a SPH-FEM Coupling Method

A coupled numerical calculation method combining smooth particle hydrodynamics(SPH)and the finite element method(FEM)was implemented to investigate the seismic response of horizontal storage tanks.Anumericalmodel of a horizontal storage tank featuring a free liquid surface under seismic action was constructed using the SPH–FEM coupling method.The stored liquid was discretized using SPH particles,while the tank and supports were discretized using the FEM.The interaction between the stored liquid and the tank was simulated by using the meshless particle contact method.Then,the numerical simulation results were compared and analyzed against seismic simulation shaking table test data to validate the method.Subsequently,a series of numerical models,considering different liquid storage volumes and seismic effects,were constructed to obtain time history data of base shear and top center displacement,which revealed the seismic performance of horizontal storage tanks.Numerical simulation results and experimental data showed good agreement,with an error rate of less than 18.85%.And this conformity signifies the rationality of the SPH-FEM coupling method.The base shear and top center displacement values obtained by the coupled SPH-FEM method were only 53.3% to 69.1% of those calculated by the equivalent mass method employed in the current code.As the stored liquid volume increased,the seismic response of the horizontal storage tank exhibited a gradual upward trend,with the seismic response increasing from 73% to 388% for every 35% increase in stored liquid volume.The maximum von Mises stress of the tank and the supports remained below the steel yield strength during the earthquake.The coupled SPH-FEM method holds certain advantages in studying the seismic problems of tanks with complex structural forms,particularly due to the representation of the flow field distribution during earthquakes by involving reservoir fluid participation.

Analysis of faulting destruction and water supply pipeline damage from the first mainshock of the February 6,2023 Türkiye earthquake doublet

In 2023,two consecutive earthquakes exceeding a magnitude of 7 occurred in Türkiye,causing severe casualties and economic losses.The damage to critical urban infrastructure and building structures,including highways,railroads,and water supply pipelines,was particularly severe in areas where these structures intersected the seismogenic fault.Critical infrastructure projects that traverse active faults are susceptible to the influence of fault movement,pulse velocity,and ground motions.In this study,we used a unique approach to analyze the acceleration records obtained from the seismic station array(9 strong ground motion stations)located along the East Anatolian Fault(the seismogenic fault of the MW7.8 mainshock of the 2023 Türkiye earthquake doublet).The acceleration records were filtered and integrated to obtain the velocity and displacement time histories.We used the results of an on-site investigation,jointly conducted by China Earthquake Administration and Türkiye’s AFAD,to analyze the distribution of PGA,PGV,and PGD recorded by the strong motion array of the East Anatolian Fault.We found that the maximum horizontal PGA in this earthquake was 3.0 g,and the maximum co-seismic surface displacement caused by the East Anatolian Fault rupture was 6.50 m.As the fault rupture propagated southwest,the velocity pulse caused by the directional effect of the rupture increased gradually,with the maximum PGA reaching 162.3 cm/s.We also discussed the seismic safety of critical infrastructure projects traversing active faults,using two case studies of water supply pipelines in Türkiye that were damaged by earthquakes.We used a three-dimensional finite element model of the PE(polyethylene)water pipeline at the Islahiye State Hospital and fault displacement observations obtained through on-site investigation to analyze pipeline failure mechanisms.We further investigated the effect of the fault-crossing angle on seismic safety of a pipeline,based on our analysis and the failure performance of the large-diameter Thames Water pipeline during the 1999 Kocaeli earthquake.The seismic method of buried pipelines crossing the fault was summarized.

A novel control strategy for reproducing the floor motions of high-rise buildings by earthquake-simulating shake tables

To enable the experimental assessment of the seismic performance of full-scale nonstructural elements with multiple engineering parameters(EDPs),a three-layer testbed named Nonstructural Element Simulator on Shake Table(NEST)has been developed.The testbed consists of three consecutive floors of steel structure.The bottom two floors provide a space to accommodate a full-scale room.To fully explore the flexibility of NEST,we propose a novel control strategy to generate the required shake table input time histories for the testbed to track the target floor motions of the buildings of interest with high accuracy.The control strategy contains two parts:an inverse dynamic compensation via simulation of feedback control systems(IDCS)algorithm and an offline iteration procedure based on a refined nonlinear numerical model of the testbed.The key aspects of the control strategy were introduced in this paper.Experimental tests were conducted to simulate the seismic responses of a full-scale office room on the 21^(st)floor of a 42-story high-rise building.The test results show that the proposed control strategy can reproduce the target floor motions of the building of interest with less than 20%errors within the specified frequency range.

Effect of seawater on incident plane P and SV waves at ocean bottom and engineering characteristics of offshore ground motion records off the coast of southern California, USA

The effect of seawater on vertical ground motions is studied via a theoretical method and then actual offshore ground motion records are analyzed using a statistical method. A theoretical analysis of the effect of seawater on incident plane P and SV waves at ocean bottom indicate that on one hand, the affected frequency range of vertical ground motions is prominent due to P wave resonance in the water layer if the impedance ratio between the seawater and the underlying medium is large, but it is greatly suppressed if the impedance ratio is small; on the other hand, for the ocean bottom interface model selected herein, vertical ground motions consisting of mostly P waves are more easily affected by seawater than those dominated by SV waves. The statistical analysis of engineering parameters of offshore ground motion records indicate that:(1) Under the infl uence of softer surface soil at the seafl oor, both horizontal and vertical spectral accelerations of offshore motions are exaggerated at long period components, which leads to the peak spectral values moving to a longer period.(2) The spectral ratios(V/H) of offshore ground motions are much smaller than onshore ground motions near the P wave resonant frequencies in the water layer; and as the period becomes larger, the effect of seawater becomes smaller, which leads to a similar V/H at intermediate periods(near 2 s). These results are consistent with the conclusions of Boore and Smith(1999), but the V/H of offshore motion may be smaller than the onshore ground motions at longer periods(more than 5 s).

EFFECT OF MICROSTRUCTURE ON THE HARDENING AND SOFTENING BEHAVIORS OF POLYCRYSTALLINE SHAPE MEMORY ALLOYS PART Ⅰ:MICROMECHANICS CONSTITUTIVE MODELING

The effects of microstructure and its evolution on the macroscopic superelastic stress-strain response of polycrystalline Shape Memory Alloy(SMA)are studied by a microstructure-based constitutive model developed in this paper.The model is established on the following basis:(1)the transformation conditions of the unconstrained single crystal SMA microdomain(to be distinguished from the bulk single crystal),which serve as the local criterion for the derivation of overall transfor- mation yield conditions of the polycrystal;(2)the micro-to macro-transition scheme by which the connection between the polycrystal aggregates and the single crystal microdomain is established and the macroscopic transformation conditions of the polycrystal SMA are derived;(3)the quantitative incorporation of three microstruc- ture factors(i.e.,nucleation,growth and orientation distribution of martensite)into the modeling.These microstructural factors are intrinsic of specific polycrystal SMA systems and the role of each factor in the macroscopic constitutive response is quan- titatively modeled.It is demonstrated that the interplay of these factors will result in different macroscopic transformation kinematics and kinetics which are responsible for the observed macroscopic stress-strain hardening or softening response,the latter will lead to the localization and propagation of transformation bands in TiNi SMA.

MATHEMATICAL PROGRAMMING ANALYSIS OF BILINEAR RHEOLOGICAL LUBRICATION MECHANICS

Bilinear theological lubrication mechanics provides an important basis for the designs of re- cently developed electrorheological(ER)'smart'journal bearings and those lubricated by mixed fluid-solid lubri- cants.But there is not yet a reliable and efficient numerical method for such a problem of non-Newtonian flu- id mechanics.In the present paper,a finite element method(FEM)together with mat hematical programming solution is successfully used to solve such a problem.A reliable and generalized numerical method for the designs of electrorheological 'smart' journal bearings and the bearings lubricated by mixed fluid- solid lubri- cant is presented.

Study on the effect of ground motion direction on the response of engineering structure

Due to the randomness of earthquake wave magnitude and direction, and the uncertain direction of strong axis and weak axis in the construction of engineering structures, the effect of the direction of ground motion on a structure are studied herein. Ground motion records usually contain three vertical ground motion data, which are obtained by sensors arranged in accordance with the EW （East -West） direction, NS （South- North） direction and perpendicular to the surface （z） direction, referring to the construction standard of seismic stations. The seismic records in the EW and NS directions are converted to Cartesian coordinates in accordance with the rotation of θ = 0°-180°, and consequently, a countless group of new ground motion time histories are obtained. Then, the characteristics of the ground motion time history and response spectrum of each group were studied, resulting in the following observations： （1） the peak and phase of ground motion are changed with the rotation of direction θ, so that the direction θ of the maximum peak ground motion can be determined; （2） response spectrum values of each group of ground motions change along with the direction θ, and their peak, predominant period and declining curve are also different as the changes occur; then, the angle θ in the direction of the maximum peak value or the widest predominant period can be determined; and （3） the seismic response of structures with different directions of ground motion inputs has been analyzed under the same earthquake record, and the results show the difference. For some ground motion records, such as the Taft seismic wave, these differences are significant. Next, the Lushan middle school gymnasium structure was analyzed and the calculation was checked using the proposed method, where the internal force of the upper space truss varied from 25% to 28%. The research results presented herein can be used for reference in choosing the ground motion when checking the actual damage to structures following earthquakes and explaining the seismic damage. Meanwhile, it also provides a reference value for research into the most severe ground motion.

Rapid report of seismic damage to buildings in the 2022 M 6.8 Luding earthquake,China

The report summarizes the observed damage to a variety of buildings near the epicenter of the M6.8 Luding earthquake in Sichuan Province,China.They include base-isolated buildings,multi-story reinforced concrete(RC)frame buildings,and masonry buildings.The near-field region is known to be tectonically highly active,and the local intensity level is the highest,that is,0.4g peak ground acceleration(PGA)for the design basis earthquake,in the Chinese zonation of seismic ground motion parameters.The extent of damage ranged from the weak-story collapse that claimed lives to the extensive nonstructural damage that suspended occupancy.The report highlights the first observation of the destruction of rubber bearings and viscous dampers in the isolation layer of Chinese seismically isolated buildings.It also features the rare observation of the brittle shear failure of RC columns in moment-resisting frames in a region of such a high seismic design requirement.Possible reasons that may have attributed to the reported damage are suggested by providing facts observed in the field.However,careful forensic analyses are needed before any conclusive judgment can be made.

Triaxial elastoplastic damage constitutive model of unreinforced clay brick masonry wall

Due to differences in the properties of composition materials and construction techniques,unreinforced masonry is characterized by low strength,anisotropy,nonuniformity,and low ductility.In order to accurately simulate the mechanical behavior of unreinforced brick masonry walls under static and dynamic loads,a new elastoplastic damage constitutive model was proposed and the corresponding subroutine was developed based on the concrete material constitutive model.In the proposed constitutive model,the Rankine strength theory and the Drucker-Prager strength theory were used to define the tensile and compressive yield surface function of materials,respectively.Moreover,the stress updating algorithm was modified to consider the tensile plastic permanent deformation of masonry materials.To verify the accuracy of the proposed constitutive model,numerical simulations of the brick masonry under monotonic and cyclic uniaxial tension and compression loads were carried out.Comparisons among the numerical and theoretical and experimental results show that the proposed model can properly reflect the masonry material mechanical properties.Furthermore,the numerical models of four pieces of masonry walls with different mortar strengths were established.Low cyclic loadings were applied and the results show that the proposed constitutive model can properly simulate the wall shear failure characteristics,and the force-displacement hysteretic curves obtained by numerical simulation are in good agreement with the tests.Overall,the proposed elastic-plastic damage constitutive model can simulate the nonlinear behavior of unreinforced brick masonry walls very well,and can be used to predict the structural response of masonry walls.

Numerical simulation on the seismic performance of retrofitted masonry walls based on the combined finite-discrete element method

Due to the long construction life,improper design methods,brittle material properties and poor construction techniques,most existing masonry structures do not perform well during earthquakes.The retrofitting method using an external steel-meshed mortar layer is widely used to retrofit existing masonry buildings.Assessing the seismic performance of masonry walls reinforced by an external steel-meshed mortar layer reasonably and effectively is a difficult subject in the research field of masonry structures.Based on the combined finite-discrete elements method,the numerical models of retrofitted brick walls with four different masonry mortar strengths by an external mortar layer are established.The shear strength of mortar and the contact between the retrofitted mortar layer and the brick blocks are discussed in detail.The failure patterns and load-displacement curves of the retrofitted brick walls were obtained by applying low cycle reciprocating loads to the numerical model,and the bearing capacity and the failure mechanism of the retrofitted walls were obtained by comparing the failure patterns,ultimate bearing capacity,deformability and other aspects with the tests.This study provides a basis for improving the seismic strengthening design method of masonry structures and helps to better assess the seismic performance of masonry structures after retrofitting.

Preliminary report of the September 5,2022 M_(S) 6.8 Luding earthquake,Sichuan,China

The 2022 M_(S)6.8 Luding earthquake is the strongest earthquake in Sichuan Province, Western China, since the 2017 M_(S)7.0 Jiuzhaigou earthquake. It occurred on the Moxi fault in the southeastern segment of the Xianshuihe fault, a tectonically active and mountainous region with severe secondary earthquake disasters. To better understand the seismogenic mechanism and provide scientific support for future hazard mitigation, we summarize the preliminary results of the Luding earthquake, including seismotectonic background, seismicity and mainshock source characteristics and aftershock properties, and direct and secondary damage associated with the mainshock.The peak ground displacements in the NS and EW directions observed by the nearest GNSS station SCCM are ~35 mm and ~55 mm, respectively, resulting in the maximum coseismic dislocation of 20 mm along the NWW direction, which is consistent with the sinistral slip on the Xianshuihe fault. Back-projection of teleseismic P waves suggest that the mainshock rupture propagated toward south-southeast. The seismic intensity of the mainshock estimated from the back-projection results indicates a Mercalli scale of Ⅷ or above near the ruptured area,consistent with the results from instrumental measurements and field surveys. Numerous aftershocks were reported, with the largest being M_(S)4.5. Aftershock locations(up to September 18, 2022) exhibit 3 clusters spanning an area of 100 km long and 30 km wide. The magnitude and rate of aftershocks decreased as expected, and the depths became shallower with time. The mainshock and two aftershocks show left-lateral strike-slip focal mechanisms. For the aftershock sequence, the b-value from the Gutenberg-Richter frequency-magnitude relationship, h-value, and p-value for Omori’s law for aftershock decay are 0.81, 1.4, and 1.21, respectively, indicating that this is a typical mainshock-aftershock sequence. The low b-value implies high background stress in the hypocenter region. Analysis from remote sensing satellite images and UAV data shows that the distribution of earthquake-triggered landslides was consistent with the aftershock area. Numerous small-size landslides with limited volumes were revealed, which damaged or buried the roads and severely hindered the rescue process.

Engineering Characteristics of Ground Vibration Caused by Blasting Demolition of Urban Viaducts

Ground vibration accelerations caused by the collapse of blasting demolition of urban viaducts was recorded in ordered to analyze the engineering characteristics and effects on the surrounding buildings. Through the analysis of peak ground acceleration,peak frequency,duration and response spectra of the recorded vibrations in different acceleration arrays,some conclusions are drawn: the peak ground acceleration decreases with increasing distance, and the amplitude of vertical component is higher than that of the horizontal components,especially in near source region. The peak frequency of ground acceleration decreases with distance,and in near source region,it is larger than the natural frequency of the surrounding buildings,and thus it will not have much effect on the buildings. The duration of ground acceleration caused by collapse is longer than that caused by blasting itself. The vertical response spectrum is the largest of the three components,and it decreases rapidly in the near source region of about 30 m,but beyond that the distance decreases slowly.The horizontal components are smaller than the local seismic design spectrum,while the vertical component for natural period under 0.15 s exceeds the seismic design spectrum,but the natural periods of general buildings are usually beyond that domain,so this will not have much effect on the nearby buildings.

Analytical Solution for the Transient Response of A Sloping Seabed Induced by A P-Wave Line Source

Many offshore marine structures are built on the seabed that are slightly or considerably sloping.To study the sloping seabed transient response during marine earthquakes,an analytical solution induced by a P-wave line source embedded in the solid is presented.During the derivation,the wave fields in the fluid layer and the semi-infinite solid are firstly constructed by using the generalized ray method and the fluid-solid interface reflection and transmission coefficients.Then,the analytical solution in the transformed domain is obtained by superposing these wave fields,and the analytical solution in the time domain by applying the analytical inverse Laplace transform method.The the head wave generation conditions and arrival times at the fluid-solid interface are derived through this solution.Through the use of numerical examples,the analytical solution is proved right and the impacts of the sloping angle on the hydrodynamic pressure in the sea,the seismic wave propagation in the seabed,the head wave,and the Scholte wave at the seawater-seabed interface are also addressed.

Role of dampers on the seismic performance of pin-supported wall-frame structures

Pin-supported(PS)walls have been proven effective in avoiding weak story failure of frame structures by increasing the height-wise continuous stiffness and producing uniform distribution of story drifts.However,little attention has been given to the floor velocity or acceleration responses of PS wall-frame structures,which predominate the seismic damage of various nonstructural components that are critical to the immediate occupancy and quick recovery of buildings.This paper presents a numerical evaluation of the floor velocity and acceleration responses of PS wall-frame structures,highlighting the effects of different types of dampers accompanying the PS walls.The results show that the PS walls alone significantly increase the peak floor velocity(PFV)and peak floor acceleration(PFA)responses.PS wall-frame structures with either steel or viscoelastic(VE)dampers are much less effective in reducing the PFV or PFA responses than they are in reducing the peak inter-story drift ratio(PIDR).The impact of this behavior is demonstrated by a seismic fragility analysis that incorporates demand parameters combining the maximum PIDR,average PFV and PFA.The results show that the use of VE dampers rather than hysteretic dampers results in better protection of nonstructural components in PS wall-frame structures.

Experimental study on the seismic performance of masonry wall reinforced by cement mortar and polypropylene band

Since masonry structures are prone to collapse in earthquakes,a novel joint reinforcement method with a polypropylene band(PP-band)and cement mortar(CM)has been put forward.Compared with the common reinforcement methods,this method not only facilitates construction but also ensures lower reinforcement cost.To systematically explore the influence of joint reinforcement on the seismic performance of masonry walls,quasi-static tests were carried out on six specimens with different reinforcement forms.The test results show that the joint action of PP-band and CM can significantly improve the specimen′s brittle failure characteristics and enhance the integrity of the specimen after cracking.Compared with the specimen without reinforcement,each of the seismic performance indexes of the joint reinforced specimen had obvious improvement.The maximum increased rate about peak load and ductility of the joint reinforced specimen is 100.6%and 233.4%,respectively.

Preliminary investigation of building damage in Hatay under February 6,2023 Turkey earthquakes

On February 6,2023,an M_(w)7.8 earthquake hit the south of Kahramanmaras prefecture,Turkey,followed by another M_(w)7.5 earthquake after nine hours in the middle region of the Kahramanmaras prefecture.More than 84,000 buildings collapsed or were severely damaged,and more than 50,000 lives were lost in Turkey and Syria.Some of the authors,as members of Chinese rescue team,entered Antakya,Hatay prefecture,and investigated the damaged buildings.This paper first summarizes the damage patterns of buildings and provides three reasons for the massive number of collapsed buildings;i.e.,the lack of seismic measures for better ductility,site effects such as liquefaction and surface rupture,and pronounced low-frequency components of the ground motions.Next,the seismic responses of two typical buildings are calculated based on the geometric data estimated by visual inspection.The results imply that the resonance of the whole structure and the poorer ductility of key members resulted in the collapse of buildings.Finally,some conclusions are drawn.Note that although a large number of buildings were seriously damaged to collapse,the majority of buildings in the areas of extreme shaking were lightly or moderately damaged,which implies that well designed and constructed buildings were able to survive and protect human lives even in over-design earthquakes.

Electrical resistivity change of saturated sand during reliquefaction under hammering loading

The electrical resistivity method was verified as an optional technique to monitor the change of mesostructure of saturated soils.To investigate the change laws of resistivity and analyze the reliquefaction meso-mechanism during the consecutive liquefaction process,five successive impact liquefaction tests were performed in a one-dimensional cubical chamber.The resistivity variation and excess pore water pressure(EPWP)were measured.The results indicate that the excess pore water pressure experienced four stages:quick increase stage,slow dissipation stage,rapid dissipation stage,and stability stage.Meanwhile,a swift decrease of resistivity emerged before the start of the rapid dissipation stage of EPWP,and then an increasing trend of resistivity is demonstrated with the densification of soil.It is proved that the vertical pore connectivity of liquefied sand is better than its random deposit state,based on a comparative study of porosity calculated from the settlement and resistivity of sand after each test.

Rapid report of seismic damage to hospitals in the 2023 Turkey earthquake sequences

The seismic performance of medical systems is crucial for the seismic resilience of communities.The report summarizes the observed damage to twelve hospital buildings in the area affected by the MW 7.8 and MW 7.5 earthquakes on February 6,2023 in Turkey.They include five base-isolated buildings and seven fixed-base buildings in southcentral Turkey's seven most heavily affected provinces.By relating the post-quake occupancy statuses of the hospitals with the estimated seismic demands during the earthquake doublet,the report offers the following observations:(1)the base-isolated hospital buildings on friction pendulum bearings generally exhibited superior performance of achieving the goal of immediate occupancy and provided better protection for nonstructural elements than fixed-base counterparts did;(2)the fixed-base hospital buildings of reinforced concrete structures constructed after 2001 successfully achieved the goal of collapse prevention even under very high seismic demands;(3)some fixed-base hospitals also remained operational even if they were very close to the fault rupture and were subjected to higher-than-design-level earthquake ground motions.