Editorial for special issue on advanced materials for energy storage and conversion

The ever-increasing environmental problems and energy challenges have called urgent demand for utilizing green,efficient,and sustainable energy,thus promoting the development of new technologies associated with energy storage and conversion systems.Amongst a wealth of energy storage devices,Li/Na/K/Zn/Mg ion batteries,metal-air batteries,and lithium-sulfur/all-solid-state batteries together with supercapacitors as advanced power sources have attracted considerable interest due to their conspicuous merits of high energy density,long cycle life,and good rate capability.

Microstructure evolution and strengthening mechanism of high -performance powder metallurgy TA15 titanium alloy by hot rolling

Hot deformation of sintered billets by powder metallurgy(PM)is an effective preparation technique for titanium alloys,which is more significant for high-alloying alloys.In this study,Ti–6.5Al–2Zr–Mo–V(TA15)titanium alloy plates were prepared by cold press-ing sintering combined with high-temperature hot rolling.The microstructure and mechanical properties under different process paramet-ers were investigated.Optical microscope,electron backscatter diffraction,and others were applied to characterize the microstructure evolution and mechanical properties strengthening mechanism.The results showed that the chemical compositions were uniformly dif-fused without segregation during sintering,and the closing of the matrix craters was accelerated by increasing the sintering temperature.The block was hot rolled at 1200℃ with an 80%reduction under only two passes without annealing.The strength and elongation of the plate at 20–25℃ after solution and aging were 1247 MPa and 14.0%,respectively,which were increased by 24.5%and 40.0%,respect-ively,compared with the as-sintered alloy at 1300℃.The microstructure was significantly refined by continuous dynamic recrystalliza-tion,which was completed by the rotation and dislocation absorption of the substructure surrounded by low-angle grain boundaries.After hot rolling combined with heat treatment,the strength and plasticity of PM-TA15 were significantly improved,which resulted from the dense,uniform,and fine recrystallization structure and the synergistic effect of multiple slip systems.

Recent progress in visualization and digitization of coherent transformation structures and application in high-strength steel

High-strength steels are mainly composed of medium-or low-temperature microstructures,such as bainite or martensite,with coherent transformation characteristics.This type of microstructure has a high density of dislocations and fine crystallographic structural units,which ease the coordinated matching of high strength,toughness,and plasticity.Meanwhile,given its excellent welding perform-ance,high-strength steel has been widely used in major engineering constructions,such as pipelines,ships,and bridges.However,visual-ization and digitization of the effective units of these coherent transformation structures using traditional methods(optical microscopy and scanning electron microscopy)is difficult due to their complex morphology.Moreover,the establishment of quantitative relationships with macroscopic mechanical properties and key process parameters presents additional difficulty.This article reviews the latest progress in microstructural visualization and digitization of high-strength steel,with a focus on the application of crystallographic methods in the development of high-strength steel plates and welding.We obtained the crystallographic data(Euler angle)of the transformed microstruc-tures through electron back-scattering diffraction and combined them with the calculation of inverse transformation from bainite or martensite to austenite to determine the reconstruction of high-temperature parent austenite and orientation relationship(OR)during con-tinuous cooling transformation.Furthermore,visualization of crystallographic packets,blocks,and variants based on actual OR and digit-ization of various grain boundaries can be effectively completed to establish quantitative relationships with alloy composition and key process parameters,thereby providing reverse design guidance for the development of high-strength steel.

Recent advances and perspectives in MXene-based cathodes for aqueous zinc-ion batteries

Aqueous zinc-ion batteries(AZIBs)show great potential for applications in grid-scale energy storage,given their intrinsic safety,cost effectiveness,environmental friendliness,and impressive electrochemical performance.However,strong electrostatic interactions exist between zinc ions and host materials,and they hinder the development of advanced cathode materials for efficient,rapid,and stable Zn-ion storage.MXenes and their derivatives possess a large interlayer spacing,excellent hydrophilicity,outstanding electronic conductivity,and high redox activity.These materials are considered“rising star”cathode candidates for AZIBs.This comprehensive review discusses recent advances in MXenes as AZIB cathodes from the perspectives of crystal structure,Zn-storage mechanism,surface modification,interlayer engineering,and conductive network design to elucidate the correlations among their composition,structure,and electrochemical performance.This work also outlines the remaining challenges faced by MXenes for aqueous Zn-ion storage,such as the urgent need for improved toxic preparation methods,exploration of potential novel MXene cathodes,and suppression of layered MXene restacking upon cycling,and introduces the prospects of MXene-based cathode materials for high-performance AZIBs.

Characterization of local chemical ordering and deformation behavior in high entropy alloys by transmission electron microscopy

Short-range ordering(SRO)is one of the most important structural features of high entropy alloys(HEAs).However,the chemical and structural analyses of SROs are very difficult due to their small size,complexed compositions,and varied locations.Transmission electron microscopy(TEM)as well as its aberration correction techniques are powerful for characterizing SROs in these compositionally complex alloys.In this short communication,we summarized recent progresses regarding characterization of SROs using TEM in the field of HEAs.By using advanced TEM techniques,not only the existence of SROs was confirmed,but also the effect of SROs on the deformation mechanism was clarified.Moreover,the perspective related to application of TEM techniques in HEAs are also discussed.

Monodisperse magnetic metallic nanoparticles: synthesis,performance enhancement, and advanced applications

Monodisperse Fe-based and Co-based nanopar-ticles exhibit unique magnetic properties. They play important roles in magnetic storage and biomedical application. Their chemical synthesis and performance enhancement draw a lot of study interest. Investigations of magnetic metallic nano-particles are very active in many scientific fields. This paper reviews the present advances in chemical synthesis, perfor-mance enhancement, and potential applications of monodis-perse Fe-based and Co-based nanoparticles.

Microstructure evolution and phase transformation of traditional cast and spray-formed hypereutectic aluminium-silicon alloys induced by heat treatment

Microstructural evolution and phase transformation induced by different heat treatments of the hypereutectic aluminium-silicon alloy, Al-25Si-5Fe-3Cu （wt%, signed as 3C）, fabricated by traditional cast （TC） and spray forming （SF） processes, were investigated by differential scanning calorimetry （DSC） and scanning electron microscopy （SEM） combined with energy dispersive X-ray spectroscopy and X-ray diffraction techniques. The results show that A17Cu2Fe phase can be formed and transformed in TC- and SF-3C alloys between 802-813 K and 800-815 K, respectively. The transformation from β-Al5FeSi to δ-Al4FeSi2 phase via peritectic reaction can occur at around 858-870 K and 876-890 K in TC- and SF-3C alloys, respectively. The starting precipitation temperature of δ-Al4FeSi2 phase as the dominant Fe-bearing phase in the TC-3C alloy is 997 K and the exothermic peak about the peritectic transformation of δ-Al4FeSi2→β-Al5FeSi is not detected in the present DSC experiments. Also, the mechanisms of the microstructural evolution and phase transformation are discussed.

Effect of trace Ni addition on microstructure,mechanical and corrosion properties of the extruded Mg-Gd-Y-Zr-Ni alloys for dissoluble fracturing tools

Magnesium alloys,a novel functional material for the fabrication of fracturing tools,are being paid more and more attentions recently due to their relatively high mechanical properties and fast dissolubility ability after fracturing.In this study,the novel extruded Mg-10Gd-3Y-0.3Zr-xNi alloys will be reported and their microstructure,mechanical and corrosion behaviors will be also studied.The results show that Ni contents influence phase precipitation behaviors.With adding 0.2 wt%Ni,a large amount of Zr_(7)Ni_(10)phases will be precipitated insidesα-Mg matrix,directly leading to degradation of strength and large corrosion rate.With further increasing Ni contents,the precipitation phases can be changed from Mg_(5)RE to 18R-LPSO structure,resulting in higher mechanical properties and faster corrosion rate.Moreover,adding Ni element also change the texture orientation by influencing the precipitation behavior of the alloys.The alloys invented in this paper have attained the highest compressive and tensile properties among all the reported dissoluble magnesium alloys.This work is beneficial in understanding the role of Ni in the magnesium alloys and provides more materials alternatives for the fabrication of dissoluble fracturing tools.

Microstructure and thermal properties of copper matrix composites reinforced with titanium-coated graphite fibers

Milled form of mesophase pitch-based graphite fibers were coated with a titanium layer using chemical vapor deposition technique and Ti-coated graphite fiber/Cu composites were fabricated by hot-pressing sintering. The composites were characterized with X-ray diffraction, scanning/transmission electron microscopies, and by mea- suring thermal properties, including thermal conductivity and coefficient of thermal expansion （CTE）. The results show that the milled fibers are preferentially oriented in a plane perpendicular to the pressing direction, leading to anisotropic thermal properties of the composites. The Ti coating reacted with graphite fiber and formed a continuous and uniform TiC layer. This carbide layer establishes a good metallurgical interracial bonding in the composites, which can improve the thermal properties effectively. When the fiber content ranges from 35 vol% to 50 vol%, the in-plane thermal conductivities of the composites increase from 383 to 407 W.（m.K）-~, and the in-plane CTEs decrease from 9.5 x 10-6 to 6.3 10-6 K-1.

In situ scanning electron microscopy observation of deformation and fracture behavior of Ti-3Zr-2Sn-3Mo-25Nb alloy

The plastic deformation and fracture processes of Ti-3Zr-2Sn-3Mo-25Nb alloy for surgical implants were directly observed by in situ scanning electron microscopy(SEM).The effect of phase transformations on deformation-induced martensitic transformation accompanying the cyclic tensile fracture processes was investigated.The results reveal that the metastable alpha martensites(α″) promotes deformation-induced martensitic transformation to ductile fracture,whereas the omega(ω) and alpha(α) phases drastically prevent slip dislocation and deformation-induced martensitic transformation to brittle fracture.

Homogenization treatment of high Nb containing TiAl alloys with as-cast and as-forged microstructures

The effect of heat treatment on the microstructure evolution of a high Nb containing TiAl alloy has been studied. The results indicate that β-segregation, β-segregation and S-segregation in the as-cast and as-forged alloys can be effectively eliminated at the temperature above Tα （1350-1400℃） for long holding time （12-24 h） and the full lamellar （FL） microstructure is gained. For the two alloys, the lamellar colony sizes are 120 μm and 2000 μm, respectively after heat treatment at 1400℃ for 12 h. Meanwhile, the sizes are 210 μm and 3000 μm, respectively at 1350℃ for 24 h. To get a fine homogenous microstructure, the primary as-cast alloy is first subjected to preheat treatment for eliminating the segregations. After the preheat treatment, the ailoy is processed by the multi-step canned forging to attain the microstructure with fine grain size.

Effects of deformation parameters on microstructure and mechanical properties of magnesium alloy AZ31B

Plastic deformation and dynamic recrystallization (DRX) behaviors of magnesium alloy AZ31B during thermal compression and extrusion processes were studied. In addition, effects of deformation temperature and rates on the microstructure and mechanical properties were investigated. The results show that the DRX grains nucleate initially at the primary grain boundaries and the twin boundaries, and the twinning plays an important role in the grain refinement. The DRX grain size depends on the deformation temperature and strain rate The average grain size is only 1 μm when the strain rate is 5 s-1 and temperature is 250 ℃. It is also found that the DRX grain can grow up quickly at the elevated temperature. The microstructure of extruded rods was consisted of tiny equal-axis DRX grains and some elongated grains. The rods extruded slowly have tiny grains and exhibit good mechanical properties.

Effect of deformation temperature and strain rate on semi-solid deformation behavior of spray-formed Al-70%Si alloys

Spray-formed Al-70%Si(mass fraction) alloys were deformed by compression in the semi-solid state. The effects of the deformation temperature, strain rate and the microstructure were studied. Two strain rates(1s -1and 0.1s -1) and six deformation temperatures (600℃, 720℃ , 780℃, 900℃, 1000℃ and 1100℃) were chosen. The stress—strain curve exhibits a peak at low strain and then decreases to a plateau before it starts to increase again as the strain increases. The stress required for deformation at lower strain rate and at higher deformation temperatures is less than those at higher strain rate and at lower deformation temperatures. Four mechanisms of semi-solid deformation can be used to explain the different behaviors of the stress—strain curves under different conditions.

First-principles calculations of Ni–(Co)–Mn–Cu–Ti all-d-metal Heusler alloy on martensitic transformation,mechanical and magnetic properties

The martensitic transformation,mechanical,and magnetic properties of the Ni_(2)Mn_(1.5-x)Cu_(x)Ti_(0.5) (x=0.125,0.25,0.375,0.5) and Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5)[(x=0.125,y=0.125,0.25,0.375,0.5) and (x=0.125,0.25,0.375,y=0.625)]alloys were systematically studied by the first-principles calculations.For the formation energy,the martensite is smaller than the austenite,the Ni–(Co)–Mn–Cu–Ti alloys studied in this work can undergo martensitic transformation.The austenite and non-modulated (NM) martensite always present antiferromagnetic state in the Ni_(2)Mn_(1.5-x)Cu_(x)Ti_(0.5) and Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5) (y<0.625) alloys.When y=0.625 in the Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5) series,the austenite presents ferromagnetic state while the NM martensite shows antiferromagnetic state.Cu doping can decrease the thermal hysteresis and anisotropy of the Ni–(Co)–Mn–Ti alloy.Increasing Mn and decreasing Ti content can improve the shear resistance and normal stress resistance,but reduce the toughness in the Ni–Mn–Cu–Ti alloy.And the ductility of the Co–Cu co-doping alloy is inferior to that of the Ni–Mn–Cu–Ti and Ni–Co–Mn–Ti alloys.The electronic density of states was studied to reveal the essence of the mechanical and magnetic properties.

Modeling of microporosity formation and hydrogen concentration evolution during solidification of an Al-Si alloy

We simulate the evolution of hydrogen concentration and gas pore formation as equiaxed dendrites grow during solidification of a hypoeutectic aluminum-silicon(Al-Si)alloy.The applied lattice Boltzmann-cellular automaton-finite difference model incorporates the physical mechanisms of solute and hydrogen partitioning on the solid/liquid interface,as well as the transports of solute and hydrogen.After the quantitative validation by the simulation of capillary intrusion,the model is utilized to investigate the growth of the equiaxed dendrites and hydrogen porosity formation for an Al-(5 wt.%)Si alloy under different solidification conditions.The simulation data reveal that the gas pores favorably nucleate in the corners surrounded by the nearby dendrite arms.Then,the gas pores grow in a competitive mode.With the cooling rate increasing,the competition among different growing gas pores is found to be hindered,which accordingly increases the pore number density in the final solidification microstructure.In the late solidification stage,even though the solid fraction is increasing,the mean concentration of hydrogen in the residue melt tends to be constant,corresponding to a dynamic equilibrium state of hydrogen concentration in liquid.As the cooling rate increases or the initial hydrogen concentration decreases,the temperature of gas pore nucleation,the porosity fraction,and the mean porosity size decrease,whilst the mean hydrogen concentration in liquid increases in the late solidification stage.The simulated data present identical trends with the experimental results reported in literature.

Structure and luminescence of Ca_2Si_5N_8:Eu^(2+) phosphor for warm white light-emitting diodes

We have synthesized Ca2Si5N8：Eu^2＋ phosphor through a solid-state reaction and investigated its structural and luminescent properties. Our Rietveld refinement of the crystal structure of Ca1.9Eu0.1Si5N8 reveals that Eu atoms substituting for Ca atoms occupy two crystallographic positions. Between 10 K and 300 K, Ca2Si5N8：Eu^2＋ phosphor shows a broad red emission band centred at -1.97 eV-2.01 eV. The gravity centre of the excitation band is located at 3.0 eV 3.31 eV. The centroid shift of the 5d levels of Eu^2＋ is determined to be -1.17 eV, and the red-shift of the lowest absorption band to be - 0.54 eV due to the crystal field splitting. We have analysed the temperature dependence of PL by using a configuration coordinate model. The Huang-Rhys parameter S = 6.0, the phonon energy hv = 52 meV, and the Stokes shift △S = 0.57 eV are obtained. The emission intensity maximum occurring at -200 K can be explained by a trapping effect. Both photoluminescence （PL） emission intensity and decay time decrease with temperature increasing beyond 200 K due to the non-radiative process.

Microstructure and mechanical properties of ultralow carbon high-strength steel weld metals with or without Cu-Nb addition

Two types of ultralow carbon steel weld metals(with and without added Cu-Nb) were prepared using gas metal arc welding(GMAW) to investigate the correlation between the microstructure and mechanical properties of weld metals.The results of microstructure characterization showed that the weld metal without Cu-Nb was mainly composed of acicular ferrite(AF), lath bainite(LB), and granular bainite(GB).In contrast, adding Cu-Nb to the weld metal caused an evident transformation of martensite and grain coarsening.Both weld metals had a high tensile strength(more than 950 MPa) and more than 17% elongation;however, their values of toughness deviated greatly,with a difference of approximately 40 J at-50℃.Analysis of the morphologies of the fracture surfaces and secondary cracks further revealed the correlation between the microstructure and mechanical properties.The effects of adding Cu and Nb on the microstructure and mechanical properties of the weld metal are discussed;the indication is that adding Cu-Nb increases the hardenability and grain size of the weld metal and thus deteriorates the toughness.

Solidification microstructure formation in HK40 and HH40 alloys

The microstructure formation processes in HK40 and HH40 alloys were investigated through JmatP ro calculations and quenching performed during directional solidification. The phase transition routes of HK40 and HH40 alloys were determined as L → L ＋ γ→ L ＋ γ ＋ M_7C_3 →γ ＋ M_7C_3 →γ ＋ M_7C_3 ＋ M_（23）C_6→γ ＋ M_（23）C_6 and L → L ＋ δ→ L ＋ δ ＋ γ→ L ＋ δ ＋ γ ＋ M_（23）C_6→δ ＋ γ ＋ M_（23）C_6, respectively. The solidification mode was determined to be the austenitic mode（A mode） in HK40 alloy and the ferritic–austenitic solidification mode（FA mode） in HH40 alloy. In HK40 alloy, eutectic carbides directly precipitate in a liquid and coarsen during cooling. The primary γ dendrites grow at the 60° angle to each other. On the other hand, in HH40 alloy, residual δ forms because of the incomplete transformation from δ to γ. Cr_（23）C_6 carbide is produced in solid delta ferrite δ but not directly in liquid HH40 alloy. Because of carbide formation in the solid phase and no rapid growth of the dendrite in a non-preferential direction, HH40 alloy is more resistant to cast defect formation than HK40 alloy.

Microstructure and Mechanical Properties of Resistance Spot Welds for Fe-based Metallic Glass

The lap joints of Fe-based metallic glass ribbons were carried by resistance spot welding, and the microstructures of spot welds were investigated by X-ray diffraction and transmission electron microscopy. The results indicated that the perfect formations of joints without typical defects such as spatter were achieved with optimized parameters. Except for little nano-particle Fe2B, no other crystalline particle was detected by TEM, revealing that the most microstructure in spot weld remains amorphous. The maximum tensile-shearing force was 45.0 N with the optimized parameters of 1 kA weld current, 30 N electrode force and 0.02 ms weld time. The spot weld failed as pullout failure mode propagating along the interface of nugget zone. The study demonstrates that resistance spot welding is an effective and practical welding process for Fe-based metallic glass.

Microstructures and phase transformation in directionally solidified TiAl-Nb alloys

Intermetallic Ti-45Al-8Nb-(W,B,Y)(at.%)and Ti-46Al-5Nb alloys are directionally solidified at a constant growth rate of 30μm·s-1 using a Bridgman type apparatus.The quenched microstructures and lengths of different phase regions were observed and measured after various growing times of 0-30 min.Results show that the phase transformations in different phase regions are mainly depending on the high temperature microstructure and the supercooling degree during quenching process.After isothermal holding,the primary phase grows into the liquid phase,the dendrites change from equiaxed to columnar grains,and the length of the L+βphase region,L+β+αphase region and mushy zone varies,indicating that the entire directional solidification process can be described by a static equilibrium-nonequilibrium-dynamic equilibrium evolution process.In addition,the gap between the original growth interface and front interface shows that the actual crystal growth rate is not equal to the drawing velocity during directional solidification.