A green cross-linking method for the preparation of renewable threedimensional graphene sponges for efficient adsorption of Congo red dye

Graphene-based materials possess significant potential for the treatment of dye wastewater due to their exceptional adsorption properties toward stubborn pollutants.However,their utilization is hindered by high preparation costs,low yields,environmental pollution during synthesis,and challenges in regenerating the adsorbent.This study proposes a novel approach to address these limitations by developing nitrogen-doped three-dimensional(3D)polyvinyl alcohol(PVA)crosslinked graphene sponges(N-PGA)using a cross-linking method with ammonium carbonate.This method offers a relatively mild,environmentally friendly approach.Ammonium carbonate serves as both a reducing and modifying agent,facilitating the formation of the intrinsic structure of N-PGA and acting as a nitrogen source.Meanwhile,PVA is utilized as the cross-linking agent.The results demonstrate that N-PGA exhibits a favorable internal 3D hierarchical porous structure and possesses robust mechanical properties.The measured specific surface area(BET)of N-PGA was as high as406.538 m^(2)·g^(-1),which was favorable for its efficient adsorption of Congo red(CR)dye molecules.At an initial concentration of 50 mg·L^(-1),N-PGA achieved an impressive removal rate of 89.6%and an adsorption capacity of 112 mg·g^(-1)for CR dye.Furthermore,it retained 79%of its initial adsorption capacity after 10 cycles,demonstrating excellent regeneration performance.In summary,the synthesized N-PGA displays remarkable efficacy in the adsorption of CR dye in wastewater,opening up new possibilities for utilizing 3D porous graphene nanomaterials as efficient adsorbents in wastewater treatment.

Study of bias voltage effect on the performance of ta-C coating prepared by high power impulse magnetron sputtering

The mechanical and frictional properties of ta-C coatings deposited on the substrate surface affect applications in the field of cutting tools and wear-resistant components.In this paper,the effect of bias parameters on the performance of ta-C coatings was investigated based on high power impulse magnetron sputtering(HiPIMS)technology.The results show that bias voltage has a significant effect on the deposition rate,structure,and wear resistance of the coating.In the range of bias voltage−50 V to−200 V,the ta-C coating performance was the best under bias voltage−150 V.The thickness reached 530.4 nm,the hardness value reached 35.996 GPa,and the bonding force in-creased to 14.2 N.The maximum sp3 bond content was 59.53% at this condition.

Effect of manganese on the formation of hybrid zirconiumbased conversion coating on low carbon steel surface

This study revealed the effect of Mn on the formation of hybrid zirconium-based conversion coatings(HZCC)on low carbon steel.The XPS results indicated that the Mn compounds on the surface of low carbon steel were mainly MnO and Mn_(2)SiO_(4).Combined with the electrochemical measurements,the corrosion resistance of HZCC showed an increase followed by a decrease with increasing Mn concentration,which was related to the Mn_(2)SiO_(4) and SiO_(2) on the surface of low carbon steel.The excessive Mn concentration resulted in the loss of SiO_(2) and aggregation of Mn_(2)SiO_(4) on the low carbon steel surface,which caused the aggregation of Zr compounds on the surface and reduced the uniformity of the coating.Meanwhile,a moderate amount of Mn addition would be beneficial to increase the adhesion of organic coatings.

Combustion performance of pulverized coal and corresponding kinetics study after adding the additives of Fe_(2)O_(3) and CaO

Combustion performance of pulverized coal(PC)in blast furnace(BF)process is regarded as a criteria parameter to assess the prop-er injection dosage of PC.In this paper,effects of two kinds of additives,Fe_(2)O_(3) and CaO,on PC combustion were studied using the thermo-gravimetric method.The results demonstrate that both the Fe_(2)O_(3) and CaO can promote combustion performance index of PC including igni-tion index(C_(i)),burnout index(D_(b)),as well as comprehensive combustibility index(S_(n)).The S_(n) increases from 1.37×10^(−6) to 2.16×10^(−6)%2·min^(−2)·℃^(−3) as the Fe_(2)O_(3) proportion increases from 0 to 5.0wt%.Additionally,the combustion kinetics of PC was clarified using the Coats-Redfern method.The results show that the activation energy(E)of PC combustion decreases after adding the above additives.For instance,the E decreases from 56.54 to 35.75 kJ/mol when the Fe_(2)O_(3) proportion increases from 0 to 5.0wt%,which supports the improved combustion per-formance.Moreover,it is uneconomic to utilize pure Fe_(2)O_(3) and CaO in production.Based on economy analysis,we selected the iron-bearing dust(IBD)which contains much Fe_(2)O_(3) and CaO component to investigate,and got the same effects.Therefore,the IBD is a potential option for catalytic PC combustion in BF process.

Effects of iron oxide on crystallization behavior and spatial distribution of spinel in stainless steel slag

Chromium plays a vital role in stainless steel due to its ability to improve the corrosion resistance of the latter.However,the re-lease of chromium from stainless steel slag(SSS)during SSS stockpiling causes detrimental environmental issues.To prevent chromium pollution,the effects of iron oxide on crystallization behavior and spatial distribution of spinel were investigated in this work.The results revealed that FeO was more conducive to the growth of spinels compared with Fe2O3 and Fe3O4.Spinels were found to be mainly distrib-uted at the top and bottom of slag.The amount of spinel phase at the bottom decreased with the increasing FeO content,while that at the top increased.The average particle size of spinel in the slag with 18wt%FeO content was 12.8μm.Meanwhile,no notable structural changes were observed with a further increase in FeO content.In other words,the spatial distribution of spinel changed when the content of iron oxide varied in the range of 8wt%to 18wt%.Finally,less spinel was found at the bottom of slag with a FeO content of 23wt%.

Dissolution behavior of Al_(2)O_(3)inclusions into CaO-MgO-SiO_(2)-Al_(2)O_(3)-TiO_(2)system ladle slags

To investigate the dissolution behaviors of Al_(2)O_(3)inclusions in CaO-5wt%MgO-SiO_(2)-30wt%Al_(2)O_(3)-TiO_(2)system ladle slags,confocal scanning laser microscopy was conducted on the slags with different TiO_(2)contents(0-10wt%),and scanning electron microscopy was performed to study the interfacial reaction between Al_(2)O_(3)and this slag system.The results disclose that the dissolution of Al_(2)O_(3)inclusions does not result in the formation of new phases at the boundary between the slag and the inclusions.In TiO_(2)-bearing and TiO_(2)-free ladle slags,there is no difference in the dissolution mechanism of Al_(2)O_(3)inclusions at steelmaking temperatures.Boundary layer diffusion is found as the controlling step of the dissolution of Al_(2)O_(3),and the diffusion coefficient is in the range of 4.18×10^(-10)to 2.18×10^(-9)m^(2)/s at 1450-1500℃.Compared with the solubility of Al_(2)O_(3)in the slags,slag viscosity and temperature play a more profound role in the dissolution of Al_(2)O_(3)inclusions.A lower viscosity and a lower melting point of the slags are beneficial for the dissolution.Suitable addition of TiO_(2)(e.g.,5wt%)in ladle slags can enhance the dissolution of Al_(2)O_(3)inclusions because of the low viscosity and melting point of the slags,while excessive addition of TiO_(2)(e.g.,10wt%)shows the opposite trend.

High-chromium vanadium-titanium magnetite all-pellet integrated burden optimization and softening-melting behavior based on flux pellets

High-chromium vanadium-titanium magnetite(HVTM)is a crucial polymetallic-associated resource to be developed.The allpellet operation is a blast furnace trend that aims to reduce carbon dioxide emissions in the future.By referencing the production data of vanadium-titanium magnetite blast furnaces,this study explored the softening-melting behavior of high-chromium vanadium-titanium magnetite and obtained the optimal integrated burden based on flux pellets.The results show that the burden with a composition of 70wt%flux pellets and 30wt%acid pellets exhibits the best softening-melting properties.In comparison to that of the single burden,the softening-melting characteristic temperature of this burden composition was higher.The melting interval first increased from 307 to 362℃and then decreased to 282℃.The maximum pressure drop(ΔPmax)decreased from 26.76 to 19.01 kPa.The permeability index(S)dropped from 4643.5 to 2446.8 kPa·℃.The softening-melting properties of the integrated burden were apparently improved.The acid pellets played a role in withstanding load during the softening process.The flux pellets in the integrated burden exhibited a higher slag melting point,which increased the melting temperature during the melting process.The slag homogeneity and the TiC produced by over-reduction led to the gas permeability deterioration of the single burden.The segregation of the flux and acid pellets in the HVTM proportion and basicity mainly led to the better softening-melting properties of the integrated burden.

Annihilating the Formation of Silicon Carbide:Molten Salt Electrolysis of Carbon-Silica Composite to Prepare the Carbon-Silicon Hybrid for Lithium-lon Battery Anode

Silicon(Si)and carbon(C)composites hold the promise for replacing the commercial graphite anode,thus increasing the energy density of lithium-ion batteries(LIBs).To mitigate the formation of SiC,this paper reports a molten salt electrolysis approach to prepare C-Si composite by the electrolysis of C-SiO2 composites.Unlike the conventional way of making a C coating on Si,C-SiO2 composites were prepared by pyrolyzing the low-cost sucrose and silica.The electrochemical deoxidation of the C-SiO2 composites not only produces nanostructured Si inside the C matrix but also introduces voids between the C and Si owing to the volume shrinkage from converting SiO2 to Si.More importantly,the use of Mg ion-containing molten salts precludes the generation of SiC,and the electrolytic Si@C composite anode delivers a capacity of about 1500 mAh g-1 after 100 cycles at a current density of 500 mA g-1.Further,the Si@C‖LiNi0.6Co0.2Mn0.2O2 full cell delivers a high energy density of 608 Wh kg-1.Overall,the molten salt approach provides a one-step electrochemical way to convert oxides@C to metals@C functional materials.

Comparison of the interface reaction behaviors of CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) solid-state systems based on the diffusion couple method

The formation mechanism of calcium vanadate and manganese vanadate and the difference between calcium and manganese in the reaction with vanadium are basic issues in the calcification roasting and manganese roasting process with vanadium slag.In this work,CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples were prepared and roasted for different time periods to illustrate and compare the diffusion reaction mechanisms.Then,the changes in the diffusion product and diffusion coefficient were investigated and calculated based on scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS) analysis.Results show that with the extension of the roasting time,the diffusion reaction gradually proceeds among the CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples.The regional boundaries of calcium and vanadium are easily identifiable for the CaO–V_(2)O_(5) diffusion couple.Meanwhile,for the MnO_(2)–V_(2)O_(5) diffusion couple,MnO_(2) gradually decomposes to form Mn_(2)O_(3),and vanadium diffuses into the interior of Mn_(2)O_(3).Only a part of vanadium combines with manganese to form the diffusion production layer.CaV_(2)O_(6) and MnV_(2)O_(6) are the interfacial reaction products of the CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples,respectively,whose thicknesses are 39.85 and 32.13μm when roasted for 16 h.After 16 h,both diffusion couples reach the reaction equilibrium due to the limitation of diffusion.The diffusion coefficient of the CaO–V_(2)O_(5) diffusion couple is higher than that of the MnO_(2)–V_(2)O_(5) diffusion couple for the same roasting time,and the diffusion reaction between vanadium and calcium is easier than that between vanadium and manganese.

Growth and aggregation control of spinel by shear-force-based melting modification of stainless steel slag

To improve the efficiency of melting modification for stainless steel(SS) slag, a shear force was introduced in this work and its effects on the spinel and silicate melt were experimentally investigated. The results indicated that the use of shear force changed the nucleation and growth behaviors of spinel and that the effects of shear force varied with its intensity. The aggregation behavior of spinel under different shear-force conditions was studied, revealing that large spinel clusters could be formed when the stirring speed was controlled. However, no notable change in the melt structure of the silicate was detected in this study. The optimal stirring speed for the melting modification treatment was 50 r·min^(-1), which substantially promoted spinel growth and aggregation, resulting in modified SS slag with excellent chromium sequestration capability.

Effect of Ca/Mg molar ratio on the calcium-based sorbents

Steelmaking industry faces urgent demands for both steel slag utilization and CO_(2)abatement.Ca and Mg of steel slag can be extracted by acid solution and used to prepare sorbents for CO_(2)capture.In this work,the calcium-based sorbents were prepared from stainless steel slag leachate by co-precipitation,and the initial CO_(2)chemisorption capacity of the calcium-based sorbent prepared from steel slag with the Ca and Mg molar ratio of 3.64:1 was 0.40 g/g.Moreover,the effect of Ca/Mg molar ratio on the morphology,structure,and CO_(2)chemisorption capacity of the calcium-based sorbents were investigated.The results show that the optimal Ca/Mg molar ratio of sorbent for CO_(2)capture was4.2:1,and the skeleton support effect of MgO in calcium-based sorbents was determined.Meanwhile,the chemisorption kinetics of the sorbents was studied using the Avrami-Erofeev model.There were two processes of CO_(2)chemisorption,and the activation energy of the first stage(reaction control)was found to be lower than that of the second stage(diffusion control).

Effect of continuous casting speed on mold surface flow and the related near-surface distribution of non-metallic inclusions

For the control of surface defects in interstitial-free(IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. The results show that, at casting speeds of 0.8 and 1.0 m/min, a thin liquid mold flux layer forms and non-uniform floating of argon bubbles occurs, inducing the entrainment and subsequent entrapment of the liquid flux; fine inclusion particles of Al_2O_3 can also aggregate at the solidification front. At higher casting speeds of 1.4 and 1.6 m/min, the liquid mold flux can be entrained and carried deeper into the liquid steel pool because of strong level fluctuations of the liquid steel and the flux. The optimal casting speed is approximately 1.2 m/min, with the most favorable surface flow status and, correspondingly, the lowest number of inclusions near the slab surface.

Existence of Al2F-7^- in molten MF–AlF3(M = K, Cs) systems as determined by Raman spectroscopy and structural simulation

The molten mixtures of alkali metal fluorides and aluminum fluoride are applied as aluminum electrolytes or brazing fluxes.However,the presence of Al2F-7^-in such molten systems is disputed.In the present study,MF-AlF3(M=K,Cs)systems with molar ratios<1 were studied by in-situ Raman spectroscopy and molecular simulation.The results show that,in addition to AlF6^(3-),AlF5^(2-),and AlF4^-,the systems also contained Al2F-7^-.The characteristic bands in the Raman spectra belonging to Al2F-7^-were located at about 225 cm^-1,315 cm^-1,479 cm^-1,and 720 cm^-1.There are two possible structures of Al2F-7^-,which belong to the D3d and D3hpoint groups.Both of these structures are linear,and their single-point energies were found to differ by only 0.31 kcal/mol.

Biooxidation-thiosulfate leaching of refractory gold concentrate

A process of biooxidation followed by thiosulfate leaching of gold from refractory gold concentrate was investigated.Mineralogical studies on the concentrate showed that very fine gold grains(<10μm)were encapsulated in pyrite and arsenopyrite,while the proportion of monomer gold was only 21%.The gold-bearing sample was identified as a high-sulfur fine-sized wrapped-type refractory gold concentrate.The gold leaching efficiency obtained by direct cyanidation was only 59.86%.After biooxidation pretreatment,the sulfide minerals were almost completely decomposed,92 wt%of the mineral particles of the biooxidation residue were decreased to<38μm,and the proportion of monomer gold in the biooxidation residue was over 86%.Meanwhile,the gold content in the biooxidation residue was enriched to 55.60 g/t,and the S,Fe,and As contents were reduced to approximately 19.8 wt%,6.97 wt%,and 0.13 wt%,respectively.Ammoniacal thiosulfate was used for gold extraction from the biooxidation residue of the refractory gold concentrate.The results showed that the optimal reagent conditions were 0.18 M thiosulfate,0.02 M copper(II),1.0 M ammonia,and 0.24 M sulfite.Under these conditions,a maximum gold leaching efficiency of 85.05%was obtained.

Study on the mechanical activation of malachite and the leaching of complex copper ore in the Luanshya mining area, Zambia

Mechanical activation(MA) of malachite was carried out by dry planetary grinding(DPG) and wet Isa grinding(WIG) methods. When the rotational speed was increased to 400 r/min in DPG, the specific surface area of malachite reached the maximum and the particle size reached the minimum of 0.7–100 μm. Agglomeration occurred between mineral particles when the rotational speed was increased to 580 r/min in DPG.However, no agglomeration was observed among particles with sizes 0.4–3 μm in WIG. X-ray diffraction analysis showed that, at a 580 r/min rotational speed in DPG, the amorphization degree of malachite was 53.12%, whereas that in WIG was 71.40%, indicating that MA led to amorphization and distortion of crystal structures. In addition, in the Fourier transform infrared(FT-IR) spectra of activated malachite, the bands associated with –OH, CO_3^(2-)and metal lattice vibrations of Cu–O and Cu–OH were weakened, and a new H–O–H bending mode and peaks of gaseous CO_2 appeared, indicating that MA decreased the band energy, enhanced dihydroxylation, and increased the chemical reactivity of the malachite.Furthermore, the leaching behavior of copper ore was greatly improved by MA.

Effect of titanium content on the refinement of coarse columnar austenite grains during the solidification of peritectic steel

The effect of titanium content on the refinement of austenite grain size in as-cast peritectic carbon steel was investigated by fast directional solidification experiments with simulating the solidification and growth of surface and subsurface austenite in continuously cast slabs.Transmission electron microscope(TEM)and scanning electron microscope(SEM)were used to analyze the size and distribution of Ti(C,N)precipitates during solidification.Based on these results,the pinning pressure of Ti(C,N)precipitates on the growth of coarse columnar grains(CCGs)was studied.The results show that the austenite microstructure of as-cast peritectic carbon steel is mainly composed of the regions of CCGs and fine columnar grains(FCGs).Increasing the content of titanium reduces the region and the short axis of the CCGs.When the content of titanium is 0.09wt%,there is no CCG region.Dispersed microscale particles will firstly form in the liquid,which will decrease the transition temperature from FCGs to CCGs.The chain-like nanoscale Ti(C,N)will precipitate with the decrease of the transition temperature.Furthermore,calculations shows that the refinement of the CCGs is caused by the pinning effect of Ti(C,N)precipitates.

Effect of chemical composition on the element distribution,phase composition and calcification roasting process of vanadium slag

The chemical composition of vanadium slag significantly affects its element distribution and phase composition,which affect the subsequent calcification roasting process and vanadium recovery.In this work,seven kinds of vanadium slags derived from different regions in China were used as the raw materials to study the effects of different components on the vanadium slag’s elements distribution,phase composition,calcification roasting,and leaching rate of major elements using scanning electron microscope,X-ray diffraction analysis,and inductively coupled plasma-optical emission spectroscopy.The results show that the spinel phase is wrapped with silicate phase in all vanadium slag samples.The main elements in the spinel phase are Cr,V,and Ti from the interior to the exterior.The size of spinel phase in low chromium vanadium slag is larger than the other vanadium slags with higher chromium contents.The spinel phase of high-calcium and high-phosphorus vanadium slag is more dispersed.The strongest diffraction peak of vanadium spinel phase in the vanadium slag migrates to a higher diffraction angle,and(Fe_(0.6)Cr_(0.4))_(2)O_(3)is formed after calcification roasting as the chromium content increased.A large amount of Ca_(2)SiO_(4)is produced because excess Ca reacts with Si in high-calcium and high-phosphorus vanadium slag.The vanadium leaching rate reaches 88%in some vanadium slags.The chromium leaching rate is less than 5%in all vanadium slags.The silicon leaching rate of high-calcium and high-phosphorus vanadium slag is much higher than that of the other slags.The leaching rate of manganese is higher than 10%,and the leaching rates of iron and titanium are negligible.

Corrosion mechanism of magnesia-chromite refractories by ZnO-containing fayalite slags: Effect of funnel glass addition

An efficient approach for lead extraction from waste funnel glass through the lead smelting process has been proposed. To clarify the effect of funnel glass addition on the degradation of magnesia-chromite refractories by ZnO-containing fayalite slag, the corrosion behavior of magnesia-chromite refractories in lead smelting slags with different funnel glass additions from 0wt% to 40wt% was tested. Scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) was used to acquire the microstructural information of the worn refractory samples. Experimental results showed that the corrosion of magnesia-chromite refractory consisted predominantly of the dissolution of MgO into slag. ZnO and FeO reacted with periclase and chromite to form (Zn,Fe,Mg)O solid solution and (Zn,Fe,Mg)(Fe,Al,Cr)2O4 spinel, respectively. With the addition of funnel glass, the solubility of MgO increased whereas ZnO levels remained stable, thereby resulting in a reduced Mg content and an elevated Zn and Fe content in the (Zn,Fe,Mg)O solid solution and the (Zn,Fe,Mg)(Fe,Al,Cr)2O4 spinel. Considering the stability of the (Zn,Fe,Mg)O solid solution layer and the penetration depth of the slag, the optimal funnel glass addition for lead smelting was found to be 20wt%.

Kinetics of carbonated decomposition of hydrogarnet with different silica saturation coefficients

Carbonated decomposition of hydrogarnet is one of the vital reactions of the calcification–carbonation method,which is designed to dispose of low-grade bauxite and Bayer red mud and is a novel eco-friendly method.In this study,the effect of the silica saturation coefficient(x)on the carbonation of hydrogarnet was investigated from the kinetic perspective.The results indicated that the carbonation of hydrogarnets with different x values(x=0.27,0.36,0.70,and 0.73)underwent two stages with significantly different rates,and the kinetic mechanisms of the two stages can be described by the kinetic functions R3 and D3.The apparent activation energies at Stages 1 and 2 were 41.96–81.64 and 14.80–34.84 kJ/mol,respectively.Moreover,the corresponding limiting steps of the two stages were interfacial chemical reaction and diffusion.

Solvothermal synthesis and adsorption performance of layered boehmite using aluminum chloride and high-alumina fly ash

High alumina fly ash(FAHAl)is a kind of bulk solid waste unique to China,whose availability of high-value aluminum and the threat to the environment makes its high-value utilization urgent.In this work,the alumina containing leaching solution obtained from Na2CO_(3) roasting and HCl leaching of FAHAl was used as the mother liquor to prepare layered boehmite in situ.The preparation process with AlCl3 as the raw material was also compared.The formation process and mechanism of boehmite,the choice of solvent,along with the adsorption capability of Congo red were analyzed by X-ray diffraction,scanning electron microscopy,Fourier transform infrared spectroscopy,Brunauer-Emmett-Teller method and adsorption experiments.Results showed that during the preparation of layered boehmite,the precursor Al(OH)3 from the reaction of Al3+and OH-is transformed into boehmiteγ-AlOOH.The existence of ethanol is beneficial to regulate and promote the growth of boehmite crystal effectively.When water and ethanol are mixed with a volume ratio of 2:1 and used as the solvent,the maximum specific surface area of the boehmite is obtained at 135.7 m2·g^(-1),and 99.16%of Congo red can be absorbed after 10 min when AlCl3 is used as a raw material.As purified leaching solution is used as the mother liquid,the crystallinity of boehmite decreases slightly when the pH value decreases from 12.5 to 11.When pH is 11,the removal efficiency of Congo red reaches a maximum of 72.25%.This process not only achieves the extraction of aluminum and high-value utilization of FAHAl but also provides a thought to prepare layered boehmite with adsorption properties.