Abrasive wear property of laser melting/deposited Ti_2Ni/TiNi intermetallic alloy

A wear resistant intermetallic alloy consisting of TiNi primary dendrites and Ti2Ni matrix was fabricated by the laser melting deposition manufacturing process. Wear resistance of Ti2Ni/TiNi alloy was evaluated on an abrasive wear tester at room temperature under the different loads. The results show that the intermetallic alloy suffers more abrasive wear attack under low wear test load of 7, 13 and 25 N than high-chromium cast-iron. However, the intermetallic alloy exhibits better wear resistance under wear test load of 49 N. Abrasive wear of the laser melting deposition Ti2Ni/TiNi alloy is governed by micro-cutting and plowing. Pseudoelasticity of TiNi plays an active role in contributing to abrasive wear resistance.

Microstructure and mechanical properties of laser melting deposited Ti_2Ni_3Si/NiTi Laves alloys

Two Ti2Ni3Si/NiTi Laves phase alloys with chemical compositions of Ni-39Ti-11Si and Ni-42Ti-8Si (%, mole fraction, the same below), respectively, were fabricated by the laser melting deposition manufacturing process, aiming at studying the effect of Ti, Si contents on microstructure and mechanical properties of the alloys. The Ni-39Ti-11Si alloy consisting of Ti2Ni3Si primary dendrites and Ti2Ni3Si/NiTi eutectic matrix is a conventional hypereutectic Laves phase alloy while the Ni-42Ti-8Si alloy being made up of NiTi primary dendrites uniformly distributed in Ti2Ni3Si/NiTi eutectic is a new hypoeutectic alloy. Mechanical properties of the alloys were investigated by nano-indentation test. The results show that the decrease of Si and the increase of Ti contents change the microstructures of the alloys from hypereutectic to hypoeutectic, which influences the mechanical properties of the alloys remarkably. Corrosion behaviors of the alloys were also evaluated by potentiodynamic anodic polarization curves.

Morphological evolution of primary TiC carbide in laser clad TiC reinforced FeAl intermetallic composite coating

The novel rapidly solidified TiC/FeAl composite coatings were fabricated by laser cladding on the substrate of 1Cr18Ni9Ti stainless steel, particular emphasis has been placed on the growth morphologies of TiC carbide and its growth mechanism under a constant solidification conditions. Results show that the growth morphology of TiC carbide strongly depends upon the nucleation process and mass transportation process of TiC forming elements in laser melt pool. With increasing amount of titanium and carbon in melt pool, the growth morphology of TiC carbide changes from block like to star like and well developed dendrite. As the amount of titanium and carbon increases further, TiC carbide particles are found to be irregular polyhedral block. Although the growth morphologies of TiC are various,their advancing fronts are all faceted, illustrating that TiC carbide grows by the mechanism of lateral ledge growth.

High-cycle fatigue crack initiation and propagation in laser melting deposited TC18 titanium alloy

This article examines fatigue crack nucleation and propagation in laser deposited TC18 titanium alloy. The Widmanstatten structure was obtained by double-annealing treatment,. High-cycle fatigue （HCF） tests were conducted at room temperature with the stress ratio of 0.1 and the notch concentration factor Kt = 1. Fatigue cracks initiated preferentially at micropores, which had great effect on the HCF properties. The effect decreased with the decrease of pore size and the increase of distance from the pore location to the specimen surface. The crack initiation region was characterized by the cleavage facets of a lamella and the tearing of β matrix. The soft a precipitated-free zone formed along grain boundaries accelerated the crack propagation. Subsurface observation indicated that the crack preferred to propagate along the grain boundary α or border of a lamella or vertical to a lamella.

Improving Laser Beam Welding Efficiency

Laser beam welding is becoming widely used in many industrial applications. This paper reviews recent research conducted on the performance, potential and problems of thick section butt joint laser welding. Common defects that occur in laser beam welding with high power laser welding are discussed and possible solutions proposed. Methods of welding process efficiency improvement are analyzed.