Semiconductor nanostructures have gained importance due to their potential application in future nano- electronic devices. For such applications, it is extremely important to understand the electrical properties of se...Semiconductor nanostructures have gained importance due to their potential application in future nano- electronic devices. For such applications, it is extremely important to understand the electrical properties of semi- conductor nanostructures. This review presents an overview of techniques to measure the electrical properties of individual and clusters of semiconductor nanostructures using microcopy based techniques or by fabricating metal- lic electrical contacts using lithography. Then it is shown that current-voltage （I-V） characteristics can be used to determine the conduction mechanism in these nanostructures. It has been explained that various material paramet- ers can be extracted from I-V characteristics. The frequently observed conduction mechanism in these nanostruc- tures such as thermally activated conduction, space charge limited current （SCLC）, hopping conduction, Poole Frenkel conduction, Schottky emission and Fowler Nordheim （FN） tunneling are explained in detail.展开更多
The effect of metal （Ti, Ni, and Au） electrodes on humidity sensing properties of electrospun TiO2 nanofibers was investigated in this work. The devices were fabricated by evaporating metal contacts on SiO2 layer th...The effect of metal （Ti, Ni, and Au） electrodes on humidity sensing properties of electrospun TiO2 nanofibers was investigated in this work. The devices were fabricated by evaporating metal contacts on SiO2 layer thermally grown on silicon substrate. The separation between the electrodes was 90 μm for all sensors. The sensors were tested from 40% to 90% relative humidity （RH） by AC electrical characterization at room temperature. When sensors are switched between 40% and 90% RH, the corresponding response and recovery time are 3 s and 5 s for Ti-electrode sensor, 4 s and 7 s for Ni-electrode sensor, and 7 s and 13 s for Au-electrode sensor. The hysteresis was 3%, 5% and 15% for sensitivity of Ti, Ni, and Au-electrode sensors are Ti-, Ni-, and Au-electrode sensor, respectively. The 7.53 MΩ/%RH, 5.29 MΩ/%RH and 4.01 MΩ/%RH respectively at 100 Hz. Therefore Ti-electrode sensor is found to have linear response, fast response and recovery time and higher sensitivity as compared with those of Ni- and Au-electrode sensors. Comparison of humidity sensing properties of sensors with different electrode material may propose a compelling route for designing and optimizing humidity sensors.展开更多
Rutile TiO2 nanoparticles were synthesized using co-precipitation method with an average diameter of 30 nm TiO2 nanoparticle device was then fabricated on glass substrate.Aluminum electrodes were defined using photoli...Rutile TiO2 nanoparticles were synthesized using co-precipitation method with an average diameter of 30 nm TiO2 nanoparticle device was then fabricated on glass substrate.Aluminum electrodes were defined using photolithography and vacuum evaporation.A suspension of TiO2 nanoparticles was prepared in isopropanol using ultrasonic agitation.The nanoparticles were deposited between the electrodes.The device was tested by AC electrical measurements at 40%-90%relative humidity（RH）.The impedance of the TiO2nanoparticles decreases by about 80 times with the increase in RH from 40%to 90%at 100 Hz.The response time and the recovery time were 4 s and 5 s,respectively between 40%and 90%RH.At 100 Hz,the sensitivity of the aluminum electrode TiO2 nanoparticle device in the range of 40%—90%RH was17 MΩ/%RH.Complex modulus analysis also confirms the increase in DC conductivity of TiO2 nanoparticles as RH increases.展开更多
文摘Semiconductor nanostructures have gained importance due to their potential application in future nano- electronic devices. For such applications, it is extremely important to understand the electrical properties of semi- conductor nanostructures. This review presents an overview of techniques to measure the electrical properties of individual and clusters of semiconductor nanostructures using microcopy based techniques or by fabricating metal- lic electrical contacts using lithography. Then it is shown that current-voltage （I-V） characteristics can be used to determine the conduction mechanism in these nanostructures. It has been explained that various material paramet- ers can be extracted from I-V characteristics. The frequently observed conduction mechanism in these nanostruc- tures such as thermally activated conduction, space charge limited current （SCLC）, hopping conduction, Poole Frenkel conduction, Schottky emission and Fowler Nordheim （FN） tunneling are explained in detail.
基金support of the Higher Education Commission(HEC),Pakistan
文摘The effect of metal （Ti, Ni, and Au） electrodes on humidity sensing properties of electrospun TiO2 nanofibers was investigated in this work. The devices were fabricated by evaporating metal contacts on SiO2 layer thermally grown on silicon substrate. The separation between the electrodes was 90 μm for all sensors. The sensors were tested from 40% to 90% relative humidity （RH） by AC electrical characterization at room temperature. When sensors are switched between 40% and 90% RH, the corresponding response and recovery time are 3 s and 5 s for Ti-electrode sensor, 4 s and 7 s for Ni-electrode sensor, and 7 s and 13 s for Au-electrode sensor. The hysteresis was 3%, 5% and 15% for sensitivity of Ti, Ni, and Au-electrode sensors are Ti-, Ni-, and Au-electrode sensor, respectively. The 7.53 MΩ/%RH, 5.29 MΩ/%RH and 4.01 MΩ/%RH respectively at 100 Hz. Therefore Ti-electrode sensor is found to have linear response, fast response and recovery time and higher sensitivity as compared with those of Ni- and Au-electrode sensors. Comparison of humidity sensing properties of sensors with different electrode material may propose a compelling route for designing and optimizing humidity sensors.
文摘Rutile TiO2 nanoparticles were synthesized using co-precipitation method with an average diameter of 30 nm TiO2 nanoparticle device was then fabricated on glass substrate.Aluminum electrodes were defined using photolithography and vacuum evaporation.A suspension of TiO2 nanoparticles was prepared in isopropanol using ultrasonic agitation.The nanoparticles were deposited between the electrodes.The device was tested by AC electrical measurements at 40%-90%relative humidity（RH）.The impedance of the TiO2nanoparticles decreases by about 80 times with the increase in RH from 40%to 90%at 100 Hz.The response time and the recovery time were 4 s and 5 s,respectively between 40%and 90%RH.At 100 Hz,the sensitivity of the aluminum electrode TiO2 nanoparticle device in the range of 40%—90%RH was17 MΩ/%RH.Complex modulus analysis also confirms the increase in DC conductivity of TiO2 nanoparticles as RH increases.
