Performance of mixed flow compressor with un-shrouded impeller strongly depends upon unsteady, asymmetrical flow fields in the axial directions. The flow through the mixed flow impeller is complex due to three-dimensi...Performance of mixed flow compressor with un-shrouded impeller strongly depends upon unsteady, asymmetrical flow fields in the axial directions. The flow through the mixed flow impeller is complex due to three-dimensional nature of geometry. In mixed flow impeller, there are clearances between the rotating impeller blades and the casing as the high pressure ratio compressors are usually open shrouded impellers. As a result, certain amount of reduction in the performance is unavoidable due to clearance flows. In the present investigations, numerical analysis is performed using a commercial code to investigate tip clearance effects on through flow. The performance of mixed flow impeller with four different clearances between impeller and stationary shroud are evaluated and compared with experimental results. The impeller performance map was obtained for different operating speeds and mass flow rates with different tip clearances. The result shows that the tip leakage flow strongly interacts with mainstream and contributes to total pressure loss and performance reduction. The pressure and performance decrement are approximately linearly proportional to the gap between impeller and stationary shroud.The analysis showed scope for improvement in design of the compressor for better performance in terms of efficiency and operating range.展开更多
This paper presents the experimental results to understand the performance of moderately loaded high speed single stage transonic axial flow compressor subjected to various configurations of axial extensions of bend s...This paper presents the experimental results to understand the performance of moderately loaded high speed single stage transonic axial flow compressor subjected to various configurations of axial extensions of bend skewed casing treatment with moderate porosity.The bend skewed casing treatment of 33%porosity was coupled with rectangular plenum chamber of depth equal to the slots depth.The five axial extensions of 20%,40%,60%,80%and 100%were used for the experimental evaluations of compressor performance.The main objective was to identify the optimum extension of the casing treatment with reference to rotor leading edge which results in maximum stall margin improvements with minimum loss in the stage efficiency.At each axial extension the compressor performance is distinctive.The improvement in the stall margin was very significant at some axial extensions with 4%–5%penalty in the stage efficiency.The compressors stage shows recovery in terms of efficiency at lower axial extensions of 20%and 40%with increase in the peak stage efficiency.Measurements of flow parameters showed the typical behaviors at near stall flow conditions.Hot wire sensor was placed at the rotor upstream in the tip region to capture the oscillations in the inlet axial and tangential velocities at stall conditions.In the absence of casing treatment the compressor exhibit abrupt stall with very high oscillations in the inlet axial and tangential velocity of the flow.The extents of oscillations reduce with bend skewed casing treatment.Few measurements were also performed in the plenum chamber and salient results are presented in this paper.展开更多
文摘Performance of mixed flow compressor with un-shrouded impeller strongly depends upon unsteady, asymmetrical flow fields in the axial directions. The flow through the mixed flow impeller is complex due to three-dimensional nature of geometry. In mixed flow impeller, there are clearances between the rotating impeller blades and the casing as the high pressure ratio compressors are usually open shrouded impellers. As a result, certain amount of reduction in the performance is unavoidable due to clearance flows. In the present investigations, numerical analysis is performed using a commercial code to investigate tip clearance effects on through flow. The performance of mixed flow impeller with four different clearances between impeller and stationary shroud are evaluated and compared with experimental results. The impeller performance map was obtained for different operating speeds and mass flow rates with different tip clearances. The result shows that the tip leakage flow strongly interacts with mainstream and contributes to total pressure loss and performance reduction. The pressure and performance decrement are approximately linearly proportional to the gap between impeller and stationary shroud.The analysis showed scope for improvement in design of the compressor for better performance in terms of efficiency and operating range.
基金Authors take this opportunity to thank Director,CSIRNAL,for funding the research program through elevenths five year plan and allow publishing the results.
文摘This paper presents the experimental results to understand the performance of moderately loaded high speed single stage transonic axial flow compressor subjected to various configurations of axial extensions of bend skewed casing treatment with moderate porosity.The bend skewed casing treatment of 33%porosity was coupled with rectangular plenum chamber of depth equal to the slots depth.The five axial extensions of 20%,40%,60%,80%and 100%were used for the experimental evaluations of compressor performance.The main objective was to identify the optimum extension of the casing treatment with reference to rotor leading edge which results in maximum stall margin improvements with minimum loss in the stage efficiency.At each axial extension the compressor performance is distinctive.The improvement in the stall margin was very significant at some axial extensions with 4%–5%penalty in the stage efficiency.The compressors stage shows recovery in terms of efficiency at lower axial extensions of 20%and 40%with increase in the peak stage efficiency.Measurements of flow parameters showed the typical behaviors at near stall flow conditions.Hot wire sensor was placed at the rotor upstream in the tip region to capture the oscillations in the inlet axial and tangential velocities at stall conditions.In the absence of casing treatment the compressor exhibit abrupt stall with very high oscillations in the inlet axial and tangential velocity of the flow.The extents of oscillations reduce with bend skewed casing treatment.Few measurements were also performed in the plenum chamber and salient results are presented in this paper.
