Effect of silicone oil on the microstructure, gelation and rheological properties of sorbitan monostearate–sesame oil oleogels

Oleogels contain oil or a non-polar liquid which is gelled with an agent called an organogelator. The aim of this study was to evaluate the effects of the addition of silicone oil(cyclopentasiloxane) to the gelation process and to the properties of sorbitan monostearate(SMS)–sesame oil oleogel and compared with that of SMS–sesame oil oleogel and SMS–cyclopentasiloxane oleogel. Three different oil phases; sesame oil phase, cyclopentasiloxane phase and a mixture of cyclopentasiloxane and sesame oil, were used to prepare oleogels with SMS gelator. The critical gelling concentrations(CGC) for oleogels were determined using different concentration of SMS in a range of 5%–22%(w/w). The characterization of the developed oleogels was done using Fourier transform infrared spectroscopy(FTIR), polarized light microscope, rheometer, X-ray diffraction(XRD) and differential scanning calorimetry(DSC). The addition of cyclopentasiloxane reduced the CGC of SMS–sesame oil oleogel from 20% to 10%(w/w). In microscopic characterization, the oleogels with a mixture of oil phases showed the longer and thicker three-dimensional gel network than that of oleogels with sesame oil and cyclopentasiloxane. FTIR studies demonstrated that this network formation was mainly due to hydrogen bonding. Rheological measurements revealed that the combination of cyclopentasiloxane and sesame oil produced strong gel with higher complex modulus values and longer linear viscoelastic region than oleogels prepared with sesame oil and cyclopentasiloxane. In addition, oleogels with the combination of the two oils had higher enthalpy( H m) and entropy( S m) thus could increase thermodynamic stability of the oleogels. Therefore, the addition of cyclopentasiloxane can improve the physical, ther-mal properties and stability of SMS–sesame oil oleogel, provide greater sensory profile and better product aesthetics. The developed oleogel can be a novel carrier for topical drug delivery.

Design and characterization of monolaurin loaded electrospun shellac nanofibers with antimicrobial activity

The aim of this study was to elucidate the optimized fabrication factors influencing the formation and properties of shellac(SHL) nanofibers loaded with an antimicrobial monolaurin(ML). The main and interaction effects of formulation and process parameters including SHL content(35%–40% w/w), ML content(1%–3% w/w), applied voltage(9–27 kV) and flow rate(0.4–1.2 ml/h) on the characteristic of nanofibers were investigated through a total of 19 experiments based on a full factorial design with three replicated center points. As a result, the SHL content was the major parameter affecting fiber diameter. Another response result revealed that the SHL content would be also the most significant negative impact on amount of beads. An increase in the concentration of SHL leaded to a reduction in the amount of beads. From the results of characterization study, it was proved that ML might be entrapped between the chains of SHL during the electrospinning process exhibiting an excellent encapsulation. According to the response surface area, small(?488 nm) and beadless(?0.48) fibers were obtained with the SHL and ML contents of 37.5% and 1.1% w/w respectively, at the applied voltage of 18 k V and the flow rate of 0.8 ml/h. In addition, the results of the kill-kinetic studies showed that SHL nanofibers loaded with ML exhibited an excellent antibacterial activity against Staphylococcus aureus, while Escherichia coli was less affected due to the hydrophilic structure of the its outer membrane. ML also exerted an antifun-gal activity by reducing the number of Candida albicans colonies. Based on their structural and antimicrobial properties, SHL nanofibers containing ML could be potentially used as a medicated dressing for wound treatment.

Design and characterization of clindamycin-loaded nanofiber patches composed of polyvinyl alcohol and tamarind seed gum and fabricated by electrohydrodynamic atomization

In this study, we developed a polymeric nanofiber patch(PNP) for topical disease treatment using electrohydrodynamic atomization(EHDA). The nanofibers were prepared using various concentrations of polyvinyl alcohol(PVA) and tamarind seed gum and loaded with clindamycin HCl as a model drug. The precursor polymer solutions were sprayed using the EHDA technique; the EHDA processing parameters were optimized to obtain blank and drug-loaded PNPs. The skin adherence, translucence, and ventilation properties of the prepared PNPs indicated that they are appropriate for topical application. The conductivity of the polymer solution increased with increasing PVA and clindamycin concentrations, and increasing the PVA concentration enhanced the solution viscosity. Based on scanning electron microscopy analysis, the PVA concentration had a pronounced effect on the morphology of the sprayed product. Nanofibers were fabricated successfully when the solution PVA concentration was 10%, 13%, or 15%(w/v). The applied voltage significantly affected the diameters of the prepared nanofibers, and the minimum nanofiber diameter was 163.86 nm. Differential scanning calorimetry and X-ray diffraction analyses indicated that the modeldrug was dispersed in PVA in an amorphous form. The PNP prepared with a PVA:gum ratio of 9:1 absorbed water better than the PVA-only PNP and the PNP with a PVA:gum ratio of 9.5:0.5. Moreover, the PNPs loaded with clindamycin at concentrations of 1%–3% prohibited the growth of Staphylococcus aureus more effectively than clindamycin gel, a commercially available product.