Petroleum geological characteristics and exploration targets of the oil-rich sags in the Central and West African Rift System

Based on seismic,drilling,and source rock analysis data,the petroleum geological characteristics and future exploration direction of the oil-rich sags in the Central and West African Rift System(CWARS)are discussed.The study shows that the Central African Rift System mainly develops high-quality lacustrine source rocks in the Lower Cretaceous,and the West African Rift System mainly develops high-quality terrigenous organic matter-rich marine source rocks in the Upper Cretaceous,and the two types of source rocks provide a material basis for the enrichment of oil and gas in the CWARS.Multiple sets of reservoir rocks including fractured basement and three sets of regional cap rocks in the Lower Cretaceous,the Upper Cretaceous,and the Paleogene are developed in the CWARS.Since the Late Mesozoic,due to the geodynamic factors including the dextral strike-slip movement of the Central African Shear Zone,the basins in different directions of the CWARS differ in terms of rifting stages,intervals of regional cap rocks,trap types and accumulation models.The NE-SW trending basins have mainly preserved one stage of rifting in the Early Cretaceous,with regional cap rocks developed in the Lower Cretaceous strata,forming traps of reverse anticlines,flower-shaped structures and basement buried hill,and two types of hydrocarbon accumulation models of"source and reservoir in the same formation,and accumulation inside source rocks"and"up-source and down-reservoir,and accumulation below source rocks".The NW–SE basins are characterized by multiple rifting stages superimposition,with the development of regional cap rocks in the Upper Cretaceous and Paleogene,forming traps of draping anticlines,faulted anticlines,antithetic fault blocks and the accumulation model of"down-source and up-reservoir,and accumulation above source rocks".The combination of reservoir and cap rocks inside source rocks of basins with multiple superimposed rifting stages,as well as the lithologic reservoirs and the shale oil inside source rocks of strong inversion basins are important fields for future exploration in basins of the CWARS.

Identification and evaluation of shale oil micromigration and its petroleum geological significance

Taking the Lower Permian Fengcheng Formation shale in Mahu Sag of Junggar Basin,NW China,as an example,core observation,test analysis,geological analysis and numerical simulation were applied to identify the shale oil micro-migration phenomenon.The hydrocarbon micro-migration in shale oil was quantitatively evaluated and verified by a self-created hydrocarbon expulsion potential method,and the petroleum geological significance of shale oil micro-migration evaluation was determined.Results show that significant micro-migration can be recognized between the organic-rich lamina and organic-poor lamina.The organic-rich lamina has strong hydrocarbon generation ability.The heavy components of hydrocarbon preferentially retained by kerogen swelling or adsorption,while the light components of hydrocarbon were migrated and accumulated to the interbedded felsic or carbonate organic-poor laminae as free oil.About 69% of the Fengcheng Formation shale samples in Well MY1 exhibit hydrocarbon charging phenomenon,while 31% of those exhibit hydrocarbon expulsion phenomenon.The reliability of the micro-migration evaluation results was verified by combining the group components based on the geochromatography effect,two-dimension nuclear magnetic resonance analysis,and the geochemical behavior of inorganic manganese elements in the process of hydrocarbon migration.Micro-migration is a bridge connecting the hydrocarbon accumulation elements in shale formations,which reflects the whole process of shale oil generation,expulsion and accumulation,and controls the content and composition of shale oil.The identification and evaluation of shale oil micro-migration will provide new perspectives for dynamically differential enrichment mechanism of shale oil and establishing a“multi-peak model in oil generation”of shale.

Whole petroleum system and ordered distribution pattern of conventional and unconventional oil and gas reservoirs

The classical source-to-trap petroleum system concept only considers the migration and accumulation of conventional oil and gas in traps driven dominantly by buoyance in a basin,although revised and improved,even some new concepts as composite petroleum system,total petroleum system,total composite petroleum system,were proposed,but they do not account for the vast unconventional oil and gas reservoirs within the system,which is not formed and distributed in traps dominantly by buoyancedriven.Therefore,the petroleum system concept is no longer adequate in dealing with all the oil and gas accumulations in a basin where significant amount of the unconventional oil and gas resources are present in addition to the conventional oil and gas accumulations.This paper looked into and analyzed the distribution characteristics of conventional and unconventional oil/gas reservoirs and their differences and correlations in petroliferous basins in China and North America,and then proposed whole petroleum system(WPS)concept,the WPS is defined as a natural system that encompasses all the conventional and unconventional oil and gas,reservoirs and resources originated from organic matter in source rocks,the geological elements and processes involving the formation,evolution,and distribution of these oil and gas,reservoirs and resources.It is found in the WPS that there are three kinds of hydrocarbons dynamic fields,three kinds of original hydrocarbons,three kinds of reservoir rocks,and the coupling of these three essential elements lead to the basic ordered distribution model of shale oil/gas reservoirs contacting or interbeded with tight oil/gas reservoirs and separated conventional oil/gas reservoirs from source rocks upward,which is expressed as“S\T-C”.Abnormal conditions lead to other three special ordered distribution models:The first is that with shale oil/gas reservoirs separated from tight oil/gas reservoirs.The second is that with two direction ordered distributions from source upward and downward.The third is with lateral distribution from source outside.

Effects of Neo-Tethyan evolution on the petroleum system of Persian Gulf Superbasin

Considering the Neo-Tethyan tectonic process and the resulting environmental changes,a geodynamic model of“one-way train loading”is proposed to analyze the formation and evolution mechanism of the Persian Gulf Superbasin with the most abundant hydrocarbons in the world.The Persian Gulf Superbasin has long been in a passive continental margin setting since the Late Paleozoic in the process of unidirectional subduction,forming a superior regional space of hydrocarbon accu-mulation.During the Jurassic-Cretaceous,the Persian Gulf Superbasin drifted slowly at low latitudes,and developed multiple superimposed source-reservoir-caprock assemblages as a combined result of several global geological events such as the Hadley Cell,the Equatorial Upwelling Current,and the Jurassic True Polar Wander.The collision during the evolution of the foreland basin since the Cenozoic led to weak destruction,which was conducive to the preservation of oil and gas.Accordingly,it is be-lieved that the slow drifting and long retention in favorable climate zone of the continent are the critical factors for hydrocarbon enrichment.Moreover,the prospects of hydrocarbon potential in other continents in the Neo-Tethyan were proposed.

Petroleum geology of marl in Triassic Leikoupo Formation and discovery significance of Well Chongtan1 in central Sichuan Basin,SW China

In 2022,the risk exploration well Chongtan1(CT1)in the Sichuan Basin revealed commercial oil and gas flow during test in a new zone–the marl of the second submember of the third member of Leikoupo Formation(Lei-32)of Middle Triassic,recording a significant discovery.However,the hydrocarbon accumulation in marl remains unclear,which restricts the selection and deployment of exploration area.Focusing on Well CT1,the hydrocarbon accumulation characteristics of Lei-32 marl are analyzed to clarify the potential zones for exploration.The following findings are obtained.First,according to the geochemical analysis of petroleum and source rocks,oil and gas in the Lei-32 marl of Well CT1 are originated from the same marl.The marl acts as both source rock and reservoir rock.Second,the Lei-32 marl in central Sichuan Basin is of lagoonal facies,with a thickness of 40–130 m,an area of about 40000 km^(2),a hydrocarbon generation intensity of(4–12)×10^(8) m^(3)/km^(2),and an estimated quantity of generated hydrocarbons of 25×10^(12) m^(3).Third,the lagoonal marl reservoirs are widely distributed in central Sichuan Basin.Typically,in Xichong–Yilong,Ziyang–Jianyang and Moxi South,the reservoirs are 20–60 m thick and cover an area of 7500 km^(2).Fourth,hydrocarbons in the lagoonal marl are generated and stored in the Lei-32 marl,which means that marl serves as both source rock and reservoir rock.They represent a new type of unconventional resource,which is worthy of exploring.Fifth,based on the interpretation of 2D and 3D seismic data from central Sichuan Basin,Xichong and Suining are defined as favorable prospects with estimated resources of(2000–3000)×10^(8) m^(3).

Petroleum geology and sub-source hydrocarbon accumulation of Permian reservoirs in Jinan Sag,eastern Junggar Basin,NW China

According to the latest drilling and the analysis of the burial history,source rock evolution history and hydrocarbon accumulation history,the sub-source hydrocarbon accumulation characteristics of the Permian reservoirs in the Jinan Sag,eastern Junggar Basin,are clarified,and the hydrocarbon accumulation model of these reservoirs is established.The results are obtained in four aspects.First,the main body of the thick salified lake basin source rocks in the Lucaogou Formation has reached the mature stage with abundant resource base.Large-scale reservoirs are developed in the Jingjingzigou,Wutonggou and Lucaogou formations.Vertically,there are multiple sets of good regional seals,the source-reservoir-caprock assemblage is good,and there are three reservoir-forming assemblages:sub-source,intra-source and above-source.Second,dissolution,hydrocarbon charging and pore-preserving effect,and presence of chlorite film effectively increase the sub-source pore space.Oil charging is earlier than the time when the reservoir becomes densified,which improves the efficiency of hydrocarbon accumulation.Third,buoyancy and source-reservoir pressure difference together constitute the driving force of oil charging,and the micro-faults within the formation give the advantage of"source-reservoir lateral docking"under the source rock.Microfractures can be critical channels for efficient seepage and continuous charging of oil in different periods.Fourth,the Jingjingzigou Formation experienced three periods of oil accumulation in the Middle-Late Permian,Middle-Late Jurassic and Late Neogene,with the characteristics of long-distance migration and accumulation in early stage,mixed charging and accumulation in middle stage and short-distance migration and high-position accumulation in late stage.The discovery and theoretical understanding of the Permian reservoirs in the Jinan Sag reveal that the thrust belt has good conditions for forming large reservoirs,and it is promising for exploration.The study results are of guidance and reference significance for oil and gas exploration in the Jinan Sag and other geologically similar areas.

Petroleum Retention,Intraformational Migration and Segmented Accumulation within the Organic-rich Shale in the Cretaceous Qingshankou Formation of the Gulong Sag,Songliao Basin,Northeast China

In this study,organic geochemical and petrological analyses were conducted on 111 shale samples from a well to understand the retention,intraformational migration and segmented accumulation(shale oil enrichment in different intervals is unconnected)features of shale oil within the organic-rich shale in the Qingshankou Formation of the Gulong Sag.Our study shows that retained petroleum characteristics in the investigated succession are mainly influenced by three factors:organic richness,intraformational migration and segmented accumulation.Organic matter richness primarily controls the amount of retained petroleum,especially the‘live’component indicated by the S_(2)value rather than the total organic carbon(TOC)figure alone.The negative expulsion efficiencies determined by mass-balance calculations of hydrocarbons reveal that petroleum from adjacent organic-rich intervals migrates into the interval of about 2386-2408 m,which is characterized by high free hydrocarbon(S_(1)),OSI and saturated hydrocarbons content,along with a greater difference inδ^(13)C values between polar compounds(including resins and asphaltenes)and saturated hydrocarbons.The depth-dependent heterogeneity of carbon isotope ratios(δ^(13)C)of mud methane gas,δ^(13)C of extracts gross composition(SARA),δ^(13)C of kerogen and SARA content of extracts suggest that the studied succession can be subdivided into four intervals.The shale oil sealing enrichment character in each interval is further corroborated by the distinctδ^(13)C values of mud methane gas in different intervals.Due to the migration of petroleum into the 2386-2408 m interval,the S_(1),OSI and saturated hydrocarbons content of the interval show higher relative values.The maturity of organic matter in the 2471-2500 m interval is at the highest with the smaller size molecular components of the retained petroleum.Thus,favorable‘sweet spots’may be found in the 2386-2408 m interval and the 2471-2500 m interval,according to the experiment results in this study.

Petroleum geology features and research developments of hydrocarbon accumulation in deep petroliferous basins

As petroleum exploration advances and as most of the oil-gas reservoirs in shallow layers have been explored, petroleum exploration starts to move toward deep basins, which has become an inevitable choice. In this paper, the petroleum geology features and research progress on oil-gas reservoirs in deep petroliferous basins across the world are characterized by using the latest results of worldwide deep petroleum exploration. Research has demonstrated that the deep petroleum shows ten major geological features. （1） While oil-gas reservoirs have been discovered in many different types of deep petroliferous basins, most have been discovered in low heat flux deep basins. （2） Many types of petroliferous traps are developed in deep basins, and tight oil-gas reservoirs in deep basin traps are arousing increasing attention. （3） Deep petroleum normally has more natural gas than liquid oil, and the natural gas ratio increases with the burial depth. （4） The residual organic matter in deep source rocks reduces but the hydrocarbon expulsion rate and efficiency increase with the burial depth. （5） There are many types of rocks in deep hydrocarbon reservoirs, and most are clastic rocks and carbonates. （6） The age of deep hydrocarbon reservoirs is widely different, but those recently discovered are pre- dominantly Paleogene and Upper Paleozoic. （7） The porosity and permeability of deep hydrocarbon reservoirs differ widely, but they vary in a regular way with lithology and burial depth. （8） The temperatures of deep oil-gas reservoirs are widely different, but they typically vary with the burial depth and basin geothermal gradient. （9） The pressures of deep oil-gas reservoirs differ significantly, but they typically vary with burial depth, genesis, and evolu- tion period. （10） Deep oil-gas reservoirs may exist with or without a cap, and those without a cap are typically of unconventional genesis. Over the past decade, six major steps have been made in the understanding of deep hydrocarbon reservoir formation. （1） Deep petroleum in petroliferous basins has multiple sources and many dif- ferent genetic mechanisms. （2） There are high-porosity, high-permeability reservoirs in deep basins, the formation of which is associated with tectonic events and subsurface fluid movement. （3） Capillary pressure differences inside and outside the target reservoir are the principal driving force of hydrocarbon enrichment in deep basins. （4） There are three dynamic boundaries for deep oil-gas reservoirs; a buoyancy-controlled threshold, hydrocarbon accumulation limits, and the upper limit of hydrocarbon generation. （5） The formation and distribution of deep hydrocarbon res- ervoirs are controlled by free, limited, and bound fluid dynamic fields. And （6） tight conventional, tight deep, tight superimposed, and related reconstructed hydrocarbon reservoirs formed in deep-limited fluid dynamic fields have great resource potential and vast scope for exploration. Compared with middle-shallow strata, the petroleum geology and accumulation in deep basins are more complex, which overlap the feature of basin evolution in different stages. We recommend that further study should pay more attention to four aspects： （1） identification of deep petroleum sources and evaluation of their relative contributions; （2） preservation conditions and genetic mechanisms of deep high-quality reservoirs with high permeability and high porosity; （3） facies feature and transformation of deep petroleum and their potential distribution; and （4） economic feasibility evaluation of deep tight petroleum exploration and development.

Research progress and key issues of ultra-deep oil and gas exploration in China

Based on the recent oil and gas discoveries and geological understandings on the ultra-deep strata of sedimentary basins, the formation and occurrence of hydrocarbons in the ultra-deep strata were investigated with respect to the processes of basin formation, hydrocarbon generation, reservoir formation and hydrocarbon accumulation, and key issues in ultra-deep oil and gas exploration were discussed. The ultra-deep strata in China underwent two extensional-convergent cycles in the Meso-Neoproterozoic Era and the Early Paleozoic Era respectively, with the tectonic-sedimentary differentiation producing the spatially adjacent source-reservoir assemblages. There are diverse large-scale carbonate reservoirs such as mound-beach, dolomite, karst fracture-vug, fractured karst and faulted zone, as well as over-pressured clastic rock and fractured bedrock reservoirs. Hydrocarbons were accumulated in multiple stages, accompanied by adjusting and finalizing in the late stage. The distribution of hydrocarbons is controlled by high-energy beach zone, regional unconformity, paleo-high and large-scale fault zone. The ultra-deep strata endow oil and gas resources as 33% of the remaining total resources, suggesting an important successive domain for hydrocarbon development in China. The large-scale pool-forming geologic units and giant hydrocarbon enrichment zones in ultra-deep strata are key and promising prospects for delivering successive discoveries. The geological conditions and enrichment zone prediction of ultra-deep oil and gas are key issues of petroleum geology.

Characteristics and main controlling factors of intra-platform shoal thin-layer dolomite reservoirs:A case study of Middle Permian Qixia Formation in Gaoshiti-Moxi area of Sichuan Basin,SW China

Based on the study of the distribution of intra-platform shoals and the characteristics of dolomite reservoirs in the Middle Permian Qixia Formation in the Gaoshiti–Moxi area of the Sichuan Basin,SW China,the controlling factors of reservoir development were analyzed,and the formation model of“intra-platform shoal thin-layer dolomite reservoir”was established.The Qixia Formation is a regressive cycle from bottom to top,in which the first member(Qi1 Member)develops low-energy open sea microfacies,and the second member(Qi2 Member)evolves into intra-platform shoal and inter-shoal sea with decreases in sea level.The intra-platform shoal is mainly distributed near the top of two secondary shallowing cycles of the Qi2 Member.The most important reservoir rock of the Qixia Formation is thin-layer fractured-vuggy dolomite,followed by vuggy dolomite.The semi-filled saddle dolomite is common in fracture-vug,and intercrystalline pores and residual dissolution pores combined with fractures to form the effective pore-fracture network.Based on the coupling analysis of sedimentary and diagenesis characteristics,the reservoir formation model of“pre-depositional micro-paleogeomorphology controlling shoal,sedimentary shoal controlling dolomite,penecontemporaneous dolomite benefiting preservation of pores,and late hydrothermal action effectively improving reservoir quality”was systematically established.The“first-order high zone”micro-paleogeomorphology before the deposition of the Qixia Formation controlled the development of large area of intra-platform shoals in Gaoshiti area during the deposition of the Qi2 Member.Shoal facies is the basic condition of early dolomitization,and the distribution range of intra-platform shoal and dolomite reservoir is highly consistent.The grain limestone of shoal facies is transformed by two stages of dolomitization.The penecontemporaneous dolomitization is conducive to the preservation of primary pores and secondary dissolved pores.The burial hydrothermal fluid enters the early dolomite body along the fractures associated with the Emeishan basalt event,makes it recrystallized into medium–coarse crystal dolomite.With the intercrystalline pores and the residual vugs after the hydrothermal dissolution along the fractures,the high-quality intra-platform shoal-type thin-layer dolomite reservoirs are formed.The establishment of this reservoir formation model can provide important theoretical support for the sustainable development of Permian gas reservoirs in the Sichuan Basin.

Modeling of multiphase flow in low permeability porous media:Effect of wettability and pore structure properties

Multiphase flow in low permeability porous media is involved in numerous energy and environmental applications.However,a complete description of this process is challenging due to the limited modeling scale and the effects of complex pore structures and wettability.To address this issue,based on the digital rock of low permeability sandstone,a direct numerical simulation is performed considering the interphase drag and boundary slip to clarify the microscopic water-oil displacement process.In addition,a dual-porosity pore network model(PNM)is constructed to obtain the water-oil relative permeability of the sample.The displacement efficiency as a recovery process is assessed under different wetting and pore structure properties.Results show that microscopic displacement mechanisms explain the corresponding macroscopic relative permeability.The injected water breaks through the outlet earlier with a large mass flow,while thick oil films exist in rough hydrophobic surfaces and poorly connected pores.The variation of water-oil relative permeability is significant,and residual oil saturation is high in the oil-wet system.The flooding is extensive,and the residual oil is trapped in complex pore networks for hydrophilic pore surfaces;thus,water relative permeability is lower in the water-wet system.While the displacement efficiency is the worst in mixed-wetting systems for poor water connectivity.Microporosity negatively correlates with invading oil volume fraction due to strong capillary resistance,and a large microporosity corresponds to low residual oil saturation.This work provides insights into the water-oil flow from different modeling perspectives and helps to optimize the development plan for enhanced recovery.

Effect of mesopore spatial distribution of HZSM-5 catalyst on zinc state and product distribution in 1-hexene aromatization

1-hexene aromatization is a promising technology to convert excess olefin in fluid catalytic cracking(FCC)gasoline to high-value benzene(B),toluene(T),and xylene.Besides,the increasing market demand of xylene has put forward higher requirements for new generation of catalyst.For increasing xylene yield in 1-hexene aromatization,the effect of mesopore structure and spatial distribution on product distribution and Zn loading was studied.Catalysts with different mesopore spatial distribution were prepared by post-treatment of parent HZSM-5 zeolite,including NaOH treatment,tetra-propylammonium hydroxide(TPAOH)treatment,and recrystallization.It was found the evenly distributed mesopore mainly prolongs the catalyst lifetime by enhancing diffusion properties but reduces the aromatics selectivity,as a result of damage of micropores close to the catalyst surface.While the selectivity of high-value xylene can be highly promoted when the mesopore is mainly distributed interior the catalyst.Besides,the state of loaded Zn was also affected by mesopores spatial distribution.On the optimized catalyst,the xylene selectivity was enhanced by 12.4%compared with conventional Zn-loaded parent HZSM-5 catalyst at conversion over 99%.It was attributed to the synergy effect of mesopores spatial distribution and optimized acid properties.This work reveals the role of mesopores in different spatial positions of 1-hexene aromatization catalysts in the reaction process and the influence on metal distribution,as well as their synergistic effect two on the improvement of xylene selectivity,which can improve our understanding of catalyst pore structure and be helpful for the rational design of high-efficient catalyst.

Miscibility of light oil and flue gas under thermal action

The miscibility of flue gas and different types of light oils is investigated through slender-tube miscible displacement experiment at high temperature and high pressure.Under the conditions of high temperature and high pressure,the miscible displacement of flue gas and light oil is possible.At the same temperature,there is a linear relationship between oil displacement efficiency and pressure.At the same pressure,the oil displacement efficiency increases gently and then rapidly to more than 90% to achieve miscible displacement with the increase of temperature.The rapid increase of oil displacement efficiency is closely related to the process that the light components of oil transit in phase state due to distillation with the rise of temperature.Moreover,at the same pressure,the lighter the oil,the lower the minimum miscibility temperature between flue gas and oil,which allows easier miscibility and ultimately better performance of thermal miscible flooding by air injection.The miscibility between flue gas and light oil at high temperature and high pressure is more typically characterized by phase transition at high temperature in supercritical state,and it is different from the contact extraction miscibility of CO_(2) under conventional high pressure conditions.

Effect of the Particle Packing Configuration on Fixed Bed Performance

Fixed-bed reactors are generally considered the optimal choice for numerous multi-phase catalytic reactions due to their excellent performance and stability.However,conventional fixed beds often encounter challenges related to inadequate mass transfer and a high pressure drop caused by the non-uniform void fraction distribution.To enhance the overall performance of fixed beds,the impact of different packing configurations on performance was investigated.Experimental and simulation methods were used to investigate the fluid flow and mass transfer performances of various packed beds under different flow rates.It was found that structured beds exhibited a significantly lower pressure drop per unit length than conventional packed beds.Furthermore,the packing configurations had a critical role in improving the overall performance of fixed beds.Specifically,structured packed beds,particularly the H-2 packing configuration,effectively reduced the pressure drop per unit length and improved the mass transfer efficiency.The H-2 packing configuration consisted of two parallel strips of particles in each layer,with strips arranged perpendicularly between adjacent layers,and the spacing between the strips varied from layer to layer.

Controllable Condensation of Aromatics and Its Mechanisms in Carbonization

In order to obtain liquefied products with higher yields of aromatic molecules to produce mesophase pitch,a good understanding of the relevant reaction mechanisms is required.Reactive molecular dynamics simulations were used to study the thermal reactions of pyrene,1-methylpyrene,7,8,9,10-tetrahydrobenzopyrene,and mixtures of pyrene with 1-octene,cyclohexene,or styrene.The reactant conversion rates,reaction rates,and product distributions were calculated and compared,and the mechanisms were analyzed and discussed.The results demonstrated that methyl and naphthenic structures in aromatics might improve the conversion rates of reactants in hydrogen transfer processes,but their steric hindrances prohibited the generation of high polymers.The naphthenic structures could generate more free radicals and presented a more obvious inhibition effect on the condensation of polymers compared with the methyl side chains.It was discovered that when different olefins were mixed with pyrene,1-octene primarily underwent pyrolysis reactions,whereas cyclohexene mainly underwent hydrogen transfer reactions with pyrene and styrene,mostly producing superconjugated biradicals through condensation reactions with pyrene.In the mixture systems,the olefins scattered aromatic molecules,hindering the formation of pyrene trimers and higher polymers.According to the reactive molecular dynamics simulations,styrene may enhance the yield of dimer and enable the controlled polycondensation of pyrene.

Pilot Test of Preparing 2-Alkylanthraquinone Using Alkylation-Oxidation Technology

To expedite the development of industrial technology for producing 2-alkylanthraquinone,a novel pilot test of alkylation-oxidation technology was conducted.The process mainly included anthracene alkylation,separation of anthracene and 2-alkylanthracene,oxidation of 2-alkylanthracene,and product purification.Optimal alkylation conditions yielded a 91.1%conversion of anthracene and a 71.73%selectivity for 2-alkylanthracene.To address the separation problem of anthracene and 2-alkylanthracene,solvent-assisted distillation technology was developed,resulting in a 98.9%purity of 2-alkylanthracene and a 91.82%separation yield.When the molar ratio of H2O_(2) to 2-alkylanthracene was 7:1,a 98.96%conversion of 2-alkylanthracene and a 99.94%selectivity for 2-alkylanthraquinone were achieved.A novel composition of 2-alkylanthraquinone,including 2-tert-butylanthraquinone,2-tert-amylanthraquinone,and 2-hexylanthraquinone,was developed.This composition could be effectively separated and purified through a combination of crystallization and washing processes.The elemental composition of the product met the existing standards,and its hydrogenation performance closely matched that of commercially available 2-tert-amylanthraquinone products.

Combined Promoting Effects of Specific Organic Functional Groups and Alumina Surface Characteristics for the Design of a Highly Efficient NiMo/Al_(2)O_(3) Hydrodesulfurization Catalyst

To prepare a highly efficient NiMo/Al_(2)O_(3) hydrodesulfurization catalyst,the combined effects of specific organic functional groups and alumina surface characteristics were investigated.First,the correlation between the surface characteristics of four different alumina and the existing Mo species states was established.It was found that the Mo equilibrium adsorption capacity can be used as a specific descriptor to quantitatively evaluate the changes in surface characteristics of different alumina.A lower Mo equilibrium adsorption capacity for alumina means weaker metal-support interaction and the loaded Mo species are easier to transform into MoS2.However,the Mo-O-Al bonds still exist at the metal-support interface.The introduction of cationic surfactant hecadecyl trimethyl ammonium bromide(CTAB)can further improve Mo species dispersion through electrostatic attraction with Mo anions and interaction of its alkyl chain with the alumina surface;meanwhile,the introduction of ethylenediamine tetraacetic acid(EDTA)can complex with Ni ions to enhance the Ni-promoting effect on Mo.Therefore,the NiMo catalyst designed using alumina with lower Mo equilibrium adsorption capacity and the simultaneous addition of EDTA and CTAB exhibits the highest hydrodesulfurization activity for 4,6-dimethyl dibenzothiophene because of its proper metal-support interaction and more well-dispersed Ni-Mo-S active phases.

Novel Method for Evaluating the Aging of Aviation Turbine Engine Oils via High-Temperature Bearing Deposit Tests

Aviation turbine engine oils require excellent thermal-oxidative stability because of their high-temperature environments.High-temperature bearing deposit testing is a mandatory method for measuring the thermal-oxidative performance of aviation lubricant oils,and the relevant apparatus was improved in the present study.Two different commercial aviation turbine engine oils were tested,one with standard performance(known as the SL oil)and the other with high thermal stability,and their thermal-oxidative stability characteristics were evaluated.After 100 h of high-temperature bearing testing,the SL oil was analyzed by using various analytical techniques to investigate its thermal-oxidative process in the bearing test,with its thermal-oxidative degradation mechanism also being discussed.The results indicate that the developed high-temperature bearing apparatus easily meets the test requirements of method 3410.1 in standard FED-STD-791D.The viscosity and total acid number(TAN)of the SL oil increased with the bearing test time,and various deposits were produced in the bearing test,with the micro-particles of the carbon deposits being sphere-like,rod-like,and sheet-like in appearance.The antioxidant additives in the oil were consumed very rapidly in the first 30 h of the bearing test,with N-phenyl-1-naphthylamine being consumed faster than dioctyldiphenylamine.Overall,the oil thermal-oxidative process involves very complex physical and chemical mechanisms.

Hydrocarbon accumulation characteristics in basement reservoirs and exploration targets of deep basement reservoirs in onshore China

Based on the global basement reservoir database and the dissection of basement reservoirs in China,the characteristics of hydrocarbon accumulation in basement reservoirs are analyzed,and the favorable conditions for hydrocarbon accumulation in deep basement reservoirs are investigated to highlight the exploration targets.The discovered basement reservoirs worldwide are mainly buried in the Archean and Precambrian granitic and metamorphic formations with depths less than 4500 m,and the relatively large reservoirs have been found in rift,back-arc and foreland basins in tectonic active zones of the Meso-Cenozoic plates.The hydrocarbon accumulation in basement reservoirs exhibits the characteristics in three aspects.First,the porous-fractured reservoirs with low porosity and ultra-low permeability are dominant,where extensive hydrocarbon accumulation occurred during the weathering denudation and later tectonic reworking of the basin basement.High resistance to compaction allows the physical properties of these highly heterogeneous reservoirs to be independent of the buried depth.Second,the hydrocarbons were sourced from the formations outside the basement.The source-reservoir assemblages are divided into contacted source rock-basement and separated source rock-basement patterns.Third,the abnormal high pressure in the source rock and the normal–low pressure in the basement reservoirs cause a large pressure difference between the source rock and the reservoirs,which is conducive to the pumping effect of hydrocarbons in the deep basement.The deep basement prospects are mainly evaluated by the factors such as tectonic activity of basement,source-reservoir combination,development of large deep faults(especially strike-slip faults),and regional seals.The Precambrian crystalline basements at the margin of the intracontinental rifts in cratonic basins,as well as the Paleozoic folded basements and the Meso-Cenozoic fault-block basements adjacent to the hydrocarbon generation depressions,have favorable conditions for hydrocarbon accumulation,and thus they are considered as the main targets for future exploration of deep basement reservoirs.

Effect of bubble morphology and behavior on power consumption in non-Newtonian fluids’aeration process

Due to a prolonged operation time and low mass transfer efficiency, the primary challenge in the aeration process of non-Newtonian fluids is the high energy consumption, which is closely related to the form and rate of impeller, ventilation, rheological properties and bubble morphology in the reactor. In this perspective, through optimal computational fluid dynamics models and experiments, the relationship between power consumption, volumetric mass transfer rate(kLa) and initial bubble size(d0) was constructed to establish an efficient operation mode for the aeration process of non-Newtonian fluids. It was found that reducing the d0could significantly increase the oxygen mass transfer rate, resulting in an obvious decrease in the ventilation volume and impeller speed. When d0was regulated within 2-5 mm,an optimal kLa could be achieved, and 21% of power consumption could be saved, compared to the case of bubbles with a diameter of 10 mm.