Test is one of methods to acquire human-seat pressure distribution in driving, with the deficiency of being uneasy to obtain the stress information of soft tissue inside human body and the sheer force of interface bet...Test is one of methods to acquire human-seat pressure distribution in driving, with the deficiency of being uneasy to obtain the stress information of soft tissue inside human body and the sheer force of interface between human and seat, which can be obtained by simulation. But current simulation method focuses mainly on calculation itself other than combining it with posture prediction and cab packaging parameters, which cause it difficult to acquire accurate pressure calculation results without accurate posture of human body, and make it almost meaningless to design optimization. Therefore, a human body geometric model with posture change capability is built and linked up with Cascade Prediction Model(CPM), which takes cab packaging parameters as inputs. A detailed finite element model of driver human body is constructed and used to conduct the driver-seat interaction simulation between human body and seat. Good accordance of pressure distribution is observed between simulation and test, which validates the simulation. In addition to the distribution pattern, curves on key sections are used to analyze the pressure and shear stress on the seat surface, as well as soft tissue stress inside human body. The simulation shows that the maximum stress of buttocks locates under the ischial tuberosity, and the maximum stress of trunk occurs near the scapula posterior and the lower waist. These are the places where fatigue usually occurs. The maximum pressure of seat appears at the driver-seat contact area corresponding to the driver's maximum skin tissue stress. In order to guide the seat design and cab packaging and study the influence of posture to pressure distribution, finite element models for different levels of cab packaging parameters are created by using CPM. The pressure distributions are calculated and their tendencies varying with cab packaging parameters are obtained. The method presented provides a new way to accurately simulate the interaction between driver human body and seat, and to guide the seat design and cab packaging so as to improve seating comfort.展开更多
Setting engine emission targets to meet diesel car requirements is particularly important in engine performance development phase. Many researches are focused on associating vehicle performance with engine targets, bu...Setting engine emission targets to meet diesel car requirements is particularly important in engine performance development phase. Many researches are focused on associating vehicle performance with engine targets, but most work is done by testing, which is time and cost consuming, furthermore, the relationship of vehicle and engine will change when either engine or vehicle changes. A GT-Drive model to simulate New European Driving Cycle (NEDC) for passenger car is developed and calibrated by testing data, model precision is controlled within 5%. Time distribution of engine operating conditions when car running NEDC cycle has been analyzed, 10 critical major engine operating points are summarized according to running time proportion. Emission of NOx and smoke control regions containing these 10 points for target engine are set. Vehicle emissions are simulated and evaluated during engine development after engine performance test data are got, and engine combustion system layout and calibration are adjusted until vehicle targets are met. Vehicle is tested in chassis dynamometer finally, the testing results show a good agreement with the simulated results with an error of less than 5%, which proves that the emission value exchange of vehicle and engine is reliable. Performance target decomposition method for passenger car diesel presented can greatly shorten the development cycle and save costs.展开更多
In this paper,the proposed is a quasi-flow constitutive model with strain-rate sen- sitivity for elastic plastic large deformation.The model is based on the Quasi-flow Corner theory, and is suitable for the sheet meta...In this paper,the proposed is a quasi-flow constitutive model with strain-rate sen- sitivity for elastic plastic large deformation.The model is based on the Quasi-flow Corner theory, and is suitable for the sheet metal forming process simulation with a variable punch machine velocity. Uniaxial tensile tests and deep-drawing tests of a circular blank with square punch are carried out and numerically simulated.The consistency between the experimental and the numerically simulated results shows the validity of the present new constitutive model.展开更多
基金supported by 2011 Scientific Frontier and Interdiscipline Reformation Project of Jilin University,China(Grant No.450060445100)
文摘Test is one of methods to acquire human-seat pressure distribution in driving, with the deficiency of being uneasy to obtain the stress information of soft tissue inside human body and the sheer force of interface between human and seat, which can be obtained by simulation. But current simulation method focuses mainly on calculation itself other than combining it with posture prediction and cab packaging parameters, which cause it difficult to acquire accurate pressure calculation results without accurate posture of human body, and make it almost meaningless to design optimization. Therefore, a human body geometric model with posture change capability is built and linked up with Cascade Prediction Model(CPM), which takes cab packaging parameters as inputs. A detailed finite element model of driver human body is constructed and used to conduct the driver-seat interaction simulation between human body and seat. Good accordance of pressure distribution is observed between simulation and test, which validates the simulation. In addition to the distribution pattern, curves on key sections are used to analyze the pressure and shear stress on the seat surface, as well as soft tissue stress inside human body. The simulation shows that the maximum stress of buttocks locates under the ischial tuberosity, and the maximum stress of trunk occurs near the scapula posterior and the lower waist. These are the places where fatigue usually occurs. The maximum pressure of seat appears at the driver-seat contact area corresponding to the driver's maximum skin tissue stress. In order to guide the seat design and cab packaging and study the influence of posture to pressure distribution, finite element models for different levels of cab packaging parameters are created by using CPM. The pressure distributions are calculated and their tendencies varying with cab packaging parameters are obtained. The method presented provides a new way to accurately simulate the interaction between driver human body and seat, and to guide the seat design and cab packaging so as to improve seating comfort.
基金supported by National Hi-tech Research and Development Program of China (863 Program, Grant No. 2008AA11A115)
文摘Setting engine emission targets to meet diesel car requirements is particularly important in engine performance development phase. Many researches are focused on associating vehicle performance with engine targets, but most work is done by testing, which is time and cost consuming, furthermore, the relationship of vehicle and engine will change when either engine or vehicle changes. A GT-Drive model to simulate New European Driving Cycle (NEDC) for passenger car is developed and calibrated by testing data, model precision is controlled within 5%. Time distribution of engine operating conditions when car running NEDC cycle has been analyzed, 10 critical major engine operating points are summarized according to running time proportion. Emission of NOx and smoke control regions containing these 10 points for target engine are set. Vehicle emissions are simulated and evaluated during engine development after engine performance test data are got, and engine combustion system layout and calibration are adjusted until vehicle targets are met. Vehicle is tested in chassis dynamometer finally, the testing results show a good agreement with the simulated results with an error of less than 5%, which proves that the emission value exchange of vehicle and engine is reliable. Performance target decomposition method for passenger car diesel presented can greatly shorten the development cycle and save costs.
基金The project supported by the Scientific Foundation of National Outstanding Youth of China (10125208),the National Natural Science Foundation of China (19832020),and the National Education Committee of China
文摘In this paper,the proposed is a quasi-flow constitutive model with strain-rate sen- sitivity for elastic plastic large deformation.The model is based on the Quasi-flow Corner theory, and is suitable for the sheet metal forming process simulation with a variable punch machine velocity. Uniaxial tensile tests and deep-drawing tests of a circular blank with square punch are carried out and numerically simulated.The consistency between the experimental and the numerically simulated results shows the validity of the present new constitutive model.