EVA plastic film is the key material for V-process. Through decades of research, special EVA film for V-process has been produced. The film has adequate elongation; its maximum is about 800% in longitudinal direction ...EVA plastic film is the key material for V-process. Through decades of research, special EVA film for V-process has been produced. The film has adequate elongation; its maximum is about 800% in longitudinal direction and 750% in transversal direction. The single width of the film is 2.8 m and the double width is 5.6 m, which is the widest sheet film for V-process in China. Sheets with different thickness ranging from the thickest 0.35 mm to the thinnest 0.08 mm can meet different demands in China. The film can be used not only for V-process of iron castings, but also for the manganese steel railway frog, steel rocking support and side frame castings for train and the steel bridge box for engine truck.展开更多
Thermal stress simulation can provide a scientific reference to eliminate defects such as crack,residual stress centralization and deformation etc.,caused by thermal stress during casting solidification.To study the t...Thermal stress simulation can provide a scientific reference to eliminate defects such as crack,residual stress centralization and deformation etc.,caused by thermal stress during casting solidification.To study the thermal stress distribution during casting process,a unilateral thermal-stress coupling model was employed to simulate 3D casting stress using Finite Difference Method(FDM),namely all the traditional thermal-elastic-plastic equations are numerically and differentially discrete.A FDM/FDM numerical simulation system was developed to analyze temperature and stress fields during casting solidification process.Two practical verifications were carried out,and the results from simulation basically coincided with practical cases.The results indicated that the FDM/FDM stress simulation system can be used to simulate the formation of residual stress,and to predict the occurrence of hot tearing.Because heat transfer and stress analysis are all based on FDM,they can use the same FD model,which can avoid the matching process between different models,and hence reduce temperature-load transferring errors.This approach makes the simulation of fluid flow,heat transfer and stress analysis unify into one single model.展开更多
文摘EVA plastic film is the key material for V-process. Through decades of research, special EVA film for V-process has been produced. The film has adequate elongation; its maximum is about 800% in longitudinal direction and 750% in transversal direction. The single width of the film is 2.8 m and the double width is 5.6 m, which is the widest sheet film for V-process in China. Sheets with different thickness ranging from the thickest 0.35 mm to the thinnest 0.08 mm can meet different demands in China. The film can be used not only for V-process of iron castings, but also for the manganese steel railway frog, steel rocking support and side frame castings for train and the steel bridge box for engine truck.
基金supported by the National Natural Science Foundation of China (No.50805056)New Century Excellent Talents in University (No.NCET-09-0396)the Scientific Research Foundation for the Returned Overseas Chinese Scholars,Ministry of Education (2009)
文摘Thermal stress simulation can provide a scientific reference to eliminate defects such as crack,residual stress centralization and deformation etc.,caused by thermal stress during casting solidification.To study the thermal stress distribution during casting process,a unilateral thermal-stress coupling model was employed to simulate 3D casting stress using Finite Difference Method(FDM),namely all the traditional thermal-elastic-plastic equations are numerically and differentially discrete.A FDM/FDM numerical simulation system was developed to analyze temperature and stress fields during casting solidification process.Two practical verifications were carried out,and the results from simulation basically coincided with practical cases.The results indicated that the FDM/FDM stress simulation system can be used to simulate the formation of residual stress,and to predict the occurrence of hot tearing.Because heat transfer and stress analysis are all based on FDM,they can use the same FD model,which can avoid the matching process between different models,and hence reduce temperature-load transferring errors.This approach makes the simulation of fluid flow,heat transfer and stress analysis unify into one single model.
