Oxidation resistant low-alloyed Ti alloys with good ductility

Oxidation resistance enhancement of pure Ti often comes at the cost of reduced ductility,which is frequently the problem through alloying with sole Al,Si,W,Mo and B.To overcome the short coming of single element alloying,this paper proposes a multi-element low-alloying strategy to take advantage of synergistic effects and resolve the conflict between oxidation resistance and ductility.It demonstrates that the addition of a small quantity of Ta(0.51wt%)can boost both oxidation resistance and ductility in comparison to pure Ti.Furthermore,the combined addition of a small amount(0.54 wt%)of Ta,Nb and Si not only preserves good ductility of pure Ti,but also reduces mass gains to 14%-67%of pure Ti during 100 h oxidation at 650-850℃in air.This indicates even better oxidation resistance than that obtained through the use of Ta,Nb,or Nb+Ta additions.The Ta+Nb+Si alloying creates an oxide layer that is less porous and more resistant to stratification and spalling.Consequently,a 3-μm N-rich layer can form in the Ti substrate beneath the oxide scale,in which phase transformation generates coherent Ti_(2)N with(0001)_(Ti)as the habit plane,with N atoms prefers to diffuse along■than along[0001]_(Ti).The completely transformed Ti_(2)N region or partially transformed Ti+Ti_(2)N region can effectively impede oxygen invasion.Therefore,the multielement low-alloying strategy is promising for enhancing both oxidation resistance and mechanical properties of metallic materials in the future.

Dynamic deformation behavior of a face-centered cubic FeCoNiCrMn high-entropy alloy

In this study, mechanical tests were conducted oil a face-centered cubic FeCoNiCrMn high-entropy alloy, both in tension and compression, in a wide range of strain rates （10^-4-10^4 s^-1） to systematically investigate its dynamic response and underlying deformation mechanism. Materials with different grain sizes were tested to understand the effect of grain size, thus grain boundary volume, on the mechanical prop-erties. Microstructures of various samples both before and after deformation were examined using elec-tron backscatter diffraction and transmission electron microscopy. The dislocation structure as well as deformation-induced twins were analyzed and correlated with the measured mechanical properties. Plastic stability during tension of the current high-entropy alloy （HEA）, in particular, at dynamic strain rates, was discussed in lights of strain-rate sensitivity and work hardening rate. It was found that, under dynamic conditions, the strength and uniform ductility increased simultaneously as a result of the mas-sive formation of deformation twins. Specifically, an ultimate tensile strength of 734 MPa and uniform elongation of-63% are obtained at 2.3×10^3 s^-1, indicating that the alloy has great potential for energy absorption upon impact loading.

300 MPa grade highly ductile biodegradable Zn-2Cu-(0.2-0.8)Li alloys with novel ternary phases

Although a few high-strength biodegradable Zn alloys with yield strengths(YSs)over 300 MPa in rolled state have been developed,their elongations(ELs)are generally less than 30%.This study developed rolled Zn-2Cu-x Li(x=0.2 wt.%,0.5 wt.%,0.8 wt.%)alloys with YSs of 316-335 MPa and ELs of 44%-61%.Three-dimensional atom probe(3DAP)and time of flight secondary ion mass spectrometry(TOF-SIMS)were employed to characterize Li distribution.Three kinds of Zn-Cu-Li ternary phases are identified,which are blockyε′-(Cu_(0.5),Li_(0.5))Zn 4,blockyβ′-(Li_(0.9),Cu_(0.1))Zn 4,and small roundγparticles with high Li content in the annealed state.Other identified phases are Zn,β-LiZn 4,andε-CuZn 4 phases.With the increase of Li content in the alloys,ε′phase with 6.50 at.%Cu transforms intoβ′phase with 2.12 at.%Cu,i.e.,the average level in the alloys.Withinε′phase,there exist nano-scale Li clusters andεphase,resulting inε′/εstructure.Dense Zn laths precipitate fromβ′phase,resulting inβ′/Zn lamellar structure.The lamel-lar structure is the matrix of Zn-2Cu-0.8Li and leads to near-isotropic plasticity.Electrochemistry tests show that degradation rates fall in the range of 153-196μm/year,which decrease with Li content.All the alloys exert positive effects on the growth of MC3T3-E1 cells with 10%extract.This research reveals how microstructure evolves in Zn-2Cu-x Li alloys,which lays the foundation for their future applications.