Case study on the mechanics of NPR anchor cable compensation for large deformation tunnel in soft rock in the Transverse Mountain area,China

A study was conducted to analyze the deformation mechanism of strongly weathered quartz schist in the Daliangshan Tunnel,located in the western Transverse Mountain area.A large deformation problem was experienced during the tunnel construction.To mitigate this problem,a support system was designed incorporating negative Poisson ratio(NPR)anchor cables with negative Poisson ratio effect.Physical model experiments,field experiments,and numerical simulation experiments were conducted to investigate the compensation mechanical behavior of NPR anchor cables.The large deformations of soft rocks in the Daliangshan Tunnel are caused by a high ground stress,a high degree of joint fracture development,and a high degree of surrounding rock fragmentation.A compensation mechanics support system combining long and short NPR anchor cables was suggested to provide sufficient counter-support force(approximately 350 kN)for the surrounding rock inside the tunnel.Comparing the NPR anchor cable support system with the original support system used in the Daliangshan tunnel showed that an NPR anchor cable support system,combining cables of 6.3 m and 10.3 m in length,effectively prevented convergence of surrounding rock deformation,and the integrated settlement convergence value remained below 300 mm.This study provides an effective scientific basis for resolving large deformation problems in deeply buried soft rocks in western transverse mountain areas.

Drilling-based measuring method for the c-φ parameter of rock and its field application

The technology of drilling tests makes it possible to obtain the strength parameter of rock accurately in situ. In this paper, a new rock cutting analysis model that considers the influence of the rock crushing zone(RCZ) is built. The formula for an ultimate cutting force is established based on the limit equilibrium principle. The relationship between digital drilling parameters(DDP) and the c-φ parameter(DDP-cφ formula, where c refers to the cohesion and φ refers to the internal friction angle) is derived, and the response of drilling parameters and cutting ratio to the strength parameters is analyzed. The drillingbased measuring method for the c-φ parameter of rock is constructed. The laboratory verification test is then completed, and the difference in results between the drilling test and the compression test is less than 6%. On this basis, in-situ rock drilling tests in a traffic tunnel and a coal mine roadway are carried out, and the strength parameters of the surrounding rock are effectively tested. The average difference ratio of the results is less than 11%, which verifies the effectiveness of the proposed method for obtaining the strength parameters based on digital drilling. This study provides methodological support for field testing of rock strength parameters.

A novel method for simulating nuclear explosion with chemical explosion to form an approximate plane wave: Field test and numerical simulation

A nuclear explosion in the rock mass medium can produce strong shock waves,seismic shocks,and other destructive effects,which can cause extreme damage to the underground protection infrastructures.With the increase in nuclear explosion power,underground protection engineering enabled by explosion-proof impact theory and technology ushered in a new challenge.This paper proposes to simulate nuclear explosion tests with on-site chemical explosion tests in the form of multi-hole explosions.First,the mechanism of using multi-hole simultaneous blasting to simulate a nuclear explosion to generate approximate plane waves was analyzed.The plane pressure curve at the vault of the underground protective tunnel under the action of the multi-hole simultaneous blasting was then obtained using the impact test in the rock mass at the site.According to the peak pressure at the vault plane,it was divided into three regions:the stress superposition region,the superposition region after surface reflection,and the approximate plane stress wave zone.A numerical simulation approach was developed using PFC and FLAC to study the peak particle velocity in the surrounding rock of the underground protective cave under the action of multi-hole blasting.The time-history curves of pressure and peak pressure partition obtained by the on-site multi-hole simultaneous blasting test and numerical simulation were compared and analyzed,to verify the correctness and rationality of the formation of an approximate plane wave in the simulated nuclear explosion.This comparison and analysis also provided a theoretical foundation and some research ideas for the ensuing study on the impact of a nuclear explosion.

Optimized air-ground data fusion method for mine slope modeling

Refined 3D modeling of mine slopes is pivotal for precise prediction of geological hazards.Aiming at the inadequacy of existing single modeling methods in comprehensively representing the overall and localized characteristics of mining slopes,this study introduces a new method that fuses model data from Unmanned aerial vehicles(UAV)tilt photogrammetry and 3D laser scanning through a data alignment algorithm based on control points.First,the mini batch K-Medoids algorithm is utilized to cluster the point cloud data from ground 3D laser scanning.Then,the elbow rule is applied to determine the optimal cluster number(K0),and the feature points are extracted.Next,the nearest neighbor point algorithm is employed to match the feature points obtained from UAV tilt photogrammetry,and the internal point coordinates are adjusted through the distanceweighted average to construct a 3D model.Finally,by integrating an engineering case study,the K0 value is determined to be 8,with a matching accuracy between the two model datasets ranging from 0.0669 to 1.0373 mm.Therefore,compared with the modeling method utilizing K-medoids clustering algorithm,the new modeling method significantly enhances the computational efficiency,the accuracy of selecting the optimal number of feature points in 3D laser scanning,and the precision of the 3D model derived from UAV tilt photogrammetry.This method provides a research foundation for constructing mine slope model.

Combined blasting for protection of gob-side roadway with thick and hard roof

The deformation control of surrounding rock in gobside roadway with thick and hard roof poses a significant challenge to the safety and efficiency of coal mining.To address this issue,a novel approach combining directional and non-directional blasting techniques,known as combined blasting,was proposed.This study focuses on the experimental investigation of the proposed method in the 122108 working face in Caojiatan Coal Mine as the engineering background.The initial phase of the study involves physical model experiments to reveal the underlying mechanisms of combined blasting for protecting gob-side roadway with thick and hard roof.The results demonstrate that this approach effectively accelerates the collapse of thick and hard roofs,enhances the fragmentation and expansion coefficient of gangue,facilitates the filling of the goaf with gangue,and provides support to the overlying strata,thus reducing the subsidence of the overlying strata above the goaf.Additionally,the method involves cutting the main roof into shorter beams to decrease the stress and disrupt stress transmission pathways.Subsequent numerical simulations were conducted to corroborate the findings of the physical model experiments,thus validating the accuracy of the experimental results.Furthermore,field engineering experiments were performed,affirming the efficacy of the combined blasting method in mitigating the deformation of surrounding rock and achieving the desired protection of the gob-side roadway.

Bearing mechanism of roof and rib support structure in automatically formed roadway and its support design method

Non-pillar mining technology with automatically formed roadway is a new mining method without coal pillar reservation and roadway excavation.The stability control of automatically formed roadway is the key to the successful application of the new method.In order to realize the stability control of the roadway surrounding rock,the mechanical model of the roof and rib support structure is established,and the influence mechanism of the automatically formed roadway parameters on the compound force is revealed.On this basis,the roof and rib support structure technology of confined lightweight concrete is proposed,and its mechanical tests under different eccentricity are carried out.The results show that the bearing capacity of confined lightweight concrete specimens is basically the same as that of ordinary confined concrete specimens.The bearing capacity of confined lightweight concrete specimens under different eccentricities is 1.95 times higher than those of U-shaped steel specimens.By comparing the test results with the theoretical calculated results of the confined concrete,the calculation method of the bearing capacity for the confined lightweight concrete structure is selected.The design method of confined lightweight concrete support structure is established,and is successfully applied in the extra-large mine,Ningtiaota Coal Mine,China.

Development of multi-functional anchorage support dynamic-static coupling performance test system and its application

In underground engineering with complex conditions,the bolt(cable)anchorage support system is in an environment where static and dynamic stresses coexist,under the action of geological conditions such as high stresses and strong disturbances and construction conditions such as the application of high prestress.It is essential to study the support components performance under dynamic-static coupling conditions.Based on this,a multi-functional anchorage support dynamic-static coupling performance test system(MAC system)is developed,which can achieve 7 types of testing functions,including single component performance,anchored net performance,anchored rock performance and so on.The bolt and cable mechanical tests are conducted by MAC system under different prestress levels.The results showed that compared to the non-prestress condition,the impact resistance performance of prestressed bolts(cables)is significantly reduced.In the prestress range of 50–160 k N,the maximum reduction rate of impact energy resisted by different types of bolts is 53.9%–61.5%compared to non-prestress condition.In the prestress range of 150–300 k N,the impact energy resisted by high-strength cable is reduced by76.8%–84.6%compared to non-prestress condition.The MAC system achieves dynamic-static coupling performance test,which provide an effective means for the design of anchorage support system.

Mechanism of high-preload support based on the NPR anchor cable in layered soft rock tunnels

The control of large deformation problems in layered soft rock tunnels needs to solve urgently.The roof problem is particularly severe among the deformation issues in tunnels.This study first analyzes the asymmetric deformation modes in layered soft rock tunnels with large deformations.Subsequently,we construct a mechanical model under ideal conditions for controlling the roof of layered soft rock tunnels through high preload with the support of NPR anchor cables.The prominent roles of long and short NPR anchor cables in the support system are also analyzed.The results indicate the significance of high preload in controlling the roof of layered soft rock tunnels.The short NPR anchor cables effectively improve the integrity of the stratified soft rock layers,while the long NPR anchor cables effectively mobilize the self-bearing capacity of deep-stable rock layers.Finally,the high-preload support method with NPR anchor cables is validated to have a good effect on controlling large deformations in layered soft rock tunnels through field monitoring data.

A new elastoplastic model for bolt-grouted fractured rock

Complexities in mechanical behaviours of rock masses mainly stem from inherent discontinuities,which calls for advanced bolt-grouting techniques for stability enhancement.Understanding the mechanical properties of bolt-grouted fractured rock mass(BGFR)and developing accurate prediction methods are crucial to optimize the BGFR support strategies.This paper establishes a new elastoplastic(E-P)model based on the orthotropic and the Mohr-Coulomb(M-C)plastic-yielding criteria.The elastic parameters of the model were derived through a meso-mechanical analysis of composite materials mechanics(CMM).Laboratory BGFR specimens were prepared and uniaxial compression test and variable-angle shear test considering different bolt arrangements were carried out to obtain the mechanical parameters of the specimens.Results showed that the anisotropy of BGFR mainly depends on the relative volume content of each component material in a certain direction.Moreover,the mechanical parameters deduced from the theory of composite materials which consider the short fibre effect are shown to be in good agreement with those determined by laboratory experiments,and the variation rules maintained good consistency.Last,a case study of a real tunnel project is provided to highlight the effectiveness,validity and robustness of the developed E-P model in prediction of stresses and deformations.

Experimental study on the effect of unloading rate on gneiss rockburst

Rockburst are often encountered in tunnel construction due to the complex geological conditions.To study the influence of unloading rate on rockburst,gneiss rockburst experiments were conducted under three groups of unloading rates.A high-speed photography system and acoustic emission(AE)system were used to monitor the entire process of rockburst process in real-time.The results show that the intensity of gneiss rockburst decreases with decrease of unloading rate,which is manifested as the reduction of AE energy and fragments ejection velocity.The mechanisms are proposed to explain this effect:(i)The reduction of unloading rate changes the crack propagation mechanism in the process of rockburst.This makes the rockbursts change from the tensile failure mechanism at high unloading rate to the tension-shear mixed failure mechanism at low unloading rate,and more energy released in the form of shear crack propagation.Then,less strain energy is converted into kinetic energy of fragments ejection.(ii)Less plate cracking degree of gneiss has taken shape due to decrease of unloading rate,resulting in the destruction of rockburst incubation process.The enlightenments of reducing the unloading rate for the project are also described quantitatively.The rockburst magnitude is reduced from the medium magnitude at the unloading rate of 0.1 MPa/s to the slight magnitude at the unloading rate of 0.025 MPa/s,which was judged by the ejection velocity.

Testing method of rock structural plane using digital drilling

The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evaluating stability and designing supports in underground engineering.Currently,there are no effective testing methods for the characteristic parameters of the rock mass structural plane in underground engineering.The paper presents the digital drilling technology as a new testing method of rock mass structural planes.Flawed rock specimens with cracks of varying widths and angles were used to simulate the rock mass structural planes,and the multifunctional rock mass digital drilling test system was employed to carry out the digital drilling tests.The analysis focuses on the variation laws of drilling parameters,such as drilling pressure and drilling torque,affected by the characteristics of prefabricated cracks,and clarifies the degradation mechanism of rock equivalent compressive strength.Additionally,an identification model for the characteristic parameters of rock mass structural planes during drilling is established.The test results indicate that the average difference of the characteristics of prefabricated cracks identified by the equivalent compressive strength is 2.45°and 0.82 mm,respectively.The identification model while drilling is verified to be correct due to the high identification accuracy.Based on this,a method for testing the characteristic parameters of the surrounding rock structural plane while drilling is proposed.The research offers a theoretical and methodological foundation for precise in situ identification of structural planes of the surrounding rock in underground engineering.

Failure process and monitoring data of an extra-large landslide at the Nanfen Open-pit Iron Mine

An extra-large landslide occurred on June 19,2021,on the footwall slope of the Nanfen Open-pit Iron Mine in Liaoning Province,China,with a volume of approximately 1.2×107 m3.To elucidate the causative factors,development process,and destructive mechanisms of this catastrophic landslide,comprehensive field tests,investigations,and laboratory experiments were conducted.Initially,the heavily weathered rock mass of the slope was intersected by faults and joint fissures,facilitating rainwater infiltration.Moreover,the landslide contained a substantial clay mineral with highly developed micro-cracks and micro-pores,exhibiting strong water-absorption properties.As moisture content increased,the rock mass underwent softening,resulting in reduced strength.Ultimately,continuous heavy rainfall infiltration amplified the slope's weight,diminishing the weak structural plane's strength,leading to fracture propagation,slip plane penetration,and extensive tensile-shear and uplift failure of the slope.The study highlights poor geological conditions as the decisive factor for this landslide,with continuous heavy rainfall as the triggering factor.Presently,adverse environmental factors persistently affect the landslide,and deformation and failure continue to escalate.Hence,it is imperative to urgently implement integrated measures encompassing slope reinforcement,monitoring,and early-warning to real-time monitor the landslide's deformation and deep mechanical evolution trends.

真三轴多面快速卸荷岩爆多余能量特征实验研究

利用自主研发的真三轴岩爆实验系统,进行了一系列真三轴高压加载下水平方向不同快速卸荷面数的滞后性岩爆实验。基于能量理论,实验研究了不同卸荷面数下的岩爆储能特征、多余能量(ΔE)、多余能量释放速度(EERR)以及AE裂纹演化特征。实验得出了以下主要结论:1)岩爆的发生相较于岩石单轴加载静态破坏,主要是由于多余能量ΔE的产生,多余能量ΔE取决于岩石在岩爆前所存储的弹性应变能、峰后设备输入的能量以及残余弹性应变能,随着卸荷面数的增加,ΔE逐渐减小,但多余能量释放速度EERR却增大,导致岩爆现象变得更为剧烈;2)在真三轴高压加载条件下进行快速卸荷,会使应力应变曲线出现卸荷平台,卸荷损伤主要以张拉破坏为主,并主要集中在临空面附近,随着卸荷面数的增加卸荷损伤逐渐增大;3)在砂岩的损伤演化过程中,拉伸裂纹占据主导地位,而在最终临近岩爆阶段,剪切裂纹曲线的斜率大于拉伸裂纹,表明剪切裂纹是导致试样失稳破坏的关键因素。

Evaluation of development potential of pumped hydroelectric storage and geothermal utilization system in abandoned coal mine

Every year in China,a significant number of mines are closed or abandoned.The pumped hydroelectric storage(PHS)and geothermal utilization are vital means to efficiently repurpose resources in abandoned mine.In this work,the development potentials of the PHS and geothermal utilization systems were evaluated.Considering the geological conditions and meteorological data available of Jiahe abandoned mine,a simple evaluation model for PHS and geothermal utilization was established.The average efficiency of the PHS system exceeds 70%and the regulatable energy of a unit volume is over 1.53 kW·h/m^(3).The PHS system achieves optimal performance when the wind/solar power ratio reaches 0.6 and 0.3 in daily and year scale,respectively.In the geothermal utilization system,the outlet temperature and heat production are significantly affected by the injection flow rate.The heat production performance is more stable at lower rate flow,and the proportion of heat production is higher in the initial stage at greater flow rate.As the operating time increases,the proportion of heat production gradually decreases.The cyclic heat storage status has obvious advantages in heat generation and cooling.Furthermore,the energy-saving and emission reduction benefits of PHS and geothermal utilization systems were calculated.

Triaxial mechanical properties and precursors of instability damage in rocks with different laminar dip angles

To investigate the mechanical failure characteristics of volcanic breccia with different bedding dip angles in deep layers,triaxial compression experiments were conducted on specimens taken from volcanic rock layers in the Junggar Basin,Xinjiang.By changing the confining pressure,we compared the mechanical properties,acoustic emission characteristics,and fractal features of the acoustic emission sequence for volcanic breccia with different bedding dip angles.The research results indicate that as the bedding dip angle increases,peak strength,internal friction angle,and cohesion exhibit a“U-shaped”variation pattern.The correlation dimension of the acoustic emission amplitude was calculated using the G-P algorithm,revealing that volcanic breccia exhibits fractal characteristics.Furthermore,a positive correlation between the correlation dimension and the bedding dip angle was observed.When the stress of the test specimen reaches 0.8σ_(c),there is a significant decrease in the fractal dimension,serving as a criterion for predicting the failure of the specimen.By analyzing the changes in fractal dimension at different stress levels,the slope of the fractal dimension△D<-0.5 can be used as a precursor to failure for test specimens with a bedding dip angle of 15°≤β≤45°.Similarly,when the bedding dip angle of the specimen is 0°≤β<15°or 45°<β≤90°,△D<0 can be considered as a precursor to specimen failure.This study provides theoretical references for understanding the failure patterns of volcanic rock.

Mechanical behavior of 2G NPR bolt anchored rock samples under static disturbance loading

The deep mining of coal resources is accompanied by severe environmental challenges and various potential engineering hazards.The implementation of NPR(negative Poisson's ratio)bolts are capable of controlling large deformations in the surrounding rock effectively.This paper focuses on studying the mechanical properties of the NPR bolt under static disturbance load.The deep nonlinear mechanical experimental system was used to study the mechanical behavior of rock samples with different anchored types(unanchored/PR anchored/2G NPR anchored)under static disturbance load.The whole process of rock samples was taken by high-speed camera to obtain the real-time failure characteristics under static disturbance load.At the same time,the acoustic emission signal was collected to obtain the key characteristic parameters of acoustic emission such as acoustic emission count,energy,and frequency.The deformation at the failure of the samples was calculated and analyzed by digital speckle software.The findings indicate that the failure mode of rock is influenced by different types of anchoring.The peak failure strength of 2G NPR bolt anchored rock samples exhibits an increase of 6.5%when compared to the unanchored rock samples.The cumulative count and cumulative energy of acoustic emission exhibit a decrease of 62.16%and 62.90%,respectively.The maximum deformation of bearing capacity exhibits an increase of 59.27%,while the failure time demonstrates a delay of 42.86%.The peak failure strength of the 2G NPR bolt anchored ones under static disturbance load exhibits an increase of 5.94%when compared to the rock anchored by PR(Poisson's ratio)bolt.The cumulative count and cumulative energy of acoustic emission exhibit a decrease of 47.16%and 43.86%,respectively.The maximum deformation of the bearing capacity exhibits an increase of 50.43%,and the failure time demonstrates a delay of 32%.After anchoring by 2G NPR bolt,anchoring support effectively reduces the risk of damage caused by static disturbance load.These results demonstrate that the support effect of 2G NPR bolt materials surpasses that of PR bolt.

深部多形式应用交岔点围岩失稳机理及能量演化研究

随着采矿进入深部地层,具有长服务年限的各类巷道交岔点围岩发生强烈破坏,需要明晰深部环境下交岔点围岩失效机理,以针对性地指导修复和补强作业。通过对多地矿井交岔点维护情况的调研,全面总结了连接型、交岔型、分岔型和旋岔型(环三角柱)四类16种交岔点类型,提出了三类交岔点的典型应用形式:单一大型交岔点、嵌套式两交岔点组和环三角岩柱式交岔点群。将现场交岔点的破坏情况分为围岩局部破坏、三角岩柱破坏和整体性破坏的三种级别,从灾害的诱因和来源上,提出了外部环境因素、自身结构属性和人为设计隐患的三类13种致灾因素,并详述了各种致灾因素的致灾路径。建立了三类典型应用形式下交岔点的精细化模型,对数值软件进行二次开发,引入了畸变能密度指标进行围岩的能量分析。研究表明,交岔点围岩的畸变能峰值在三角区岩柱内,增高系数在2.5左右。最大断面处围岩畸变能同样发生积聚,增高系数在1.5左右。因此,提出了交岔点的修复需以强化三角岩柱和大断面处围岩为重点,并对深井交岔点的修复提出了以三角岩柱和大断面段补强为主的针对性方案。本研究为深部交岔点的破坏因素分析、数值模拟指标引入和修复支护提供了参考。

大断面隧道初期支护中纵向连接与拱架联合承载效应

针对大断面隧道初期支护拱架在承载时易发生平面外失稳的问题,本文通过开展单拱架全比尺试验和考虑纵向连接的拱框架结构的数值试验以及现场对比试验,对纵向连接与拱架组成的拱框架结构进行优化研究,使其横向上有足够承载能力、纵向上有较高稳定性。研究结果表明,单个拱架的破坏模式是局部面外失稳导致整体承载力丧失,考虑纵向连接的拱框架结构的平面内承载力和平面外稳定性都得到增强。通过调整纵向连接间距和拱架间距也可以调整初期支护拱框架结构和喷射混凝土的内力分担比,以充分发挥初期支护的承载能力,但纵向连接间距应小于1500 mm,拱架间距也应小于1200 mm。因而,在不改变初期支护现有结构形式的前提下,通过合理地布设纵向连接与拱架形成的具有空间承载效应的拱框架结构,不仅可以保证初期支护的承载能力,而且还提高施工效率和经济效益。研究成果可指导大断面隧道初期支护结构设计。

Dynamic response mechanism and precursor characteristics of gneiss rockburst under different initial burial depths

To investigate the influence mechanism of geostress on rockburst characteristics,three groups of gneiss rockburst experiments were conducted under different initial geostress conditions.A high-speed photography system and acoustic emission(AE)monitoring system were used to monitor the entire rockburst process in real time.The experimental results show that when the initial burial depth increases from 928 m to 1320 m,the proportion of large fracture scale in rockburst increases by 154.54%,and the AE energy increases by 565.63%,reflecting that the degree and severity of rockburst increase with the increase of burial depth.And then,two mechanisms are proposed to explain this effect,including(i)the increase of initial geostress improves the energy storage capacity of gneiss,and then,the excess energy which can be converted into kinetic energy of debris ejection increases,consequently,a more pronounced violent ejection phenomenon is observed at rockburst;(ii)the increase of initial geostress causes more sufficient plate cracks of gneiss after unloading ofσh,which provides a basis for more severe ejection of rockburst.What’s more,a precursor with clear physical meaning for rockburst is proposed under the framework of dynamic response process of crack evolution.Finally,potential value in long term rockburst warning of the precursor obtained in this study is shown via the comparison of conventional precursor.

Quasi-three-dimensional hydrodynamics of the corona region of laser irradiation of a slab

This paper introduces and establishes a quasi-three-dimensional physical model of the interaction between a laser and a slab target.In contrast to previous one-dimensional analytical models,this paper innovatively fits the real laser conditions based on an isothermal,homogeneous expansion similarity solution of the ideal hydrodynamic equations.Using this simple model,the evolution law and analytical formulae for key parameters(e.g.,temperature,density and scale length)in the corona region under certain conditions are given.The analytical solutions agree well with the relevant results of computational hydrodynamics simulation.For constant laser irradiation,the analytical solutions provide a meaningful power-law scaling relationship.The model provides a set of mathematical and physical tools that give theoretical support for adjusting parameters in experiments.