Grain refinement and mechanical properties of pure aluminum processed by accumulative extrusion bonding

Ultrafine-grained aluminum processed by a new severe plastic deformation technique, accumulative extrusion bonding (AEB), was investigated. Microstructural characterization indicated good interfacial bonding and an average grain size of ~440 nm was obtained after six passes. Tensile testing revealed that the strength reached the maximum value of 195 MPa and the total elongation exceeded 16% after five passes. The hardness was also significantly improved and almost reached saturation after the first pass. SEM fractography of AEB-processed specimens after tensile test showed that failure mode was shear ductile fracture with elongated shallow dimples. Comparison with conventional accumulative roll bonding indicates that this new AEB technique is more effective in refining grain and improving mechanical properties of the specimens.

Influence of different rolling routes on mechanical anisotropy and formability of commercially pure titanium sheet

Influence of three different rolling routes on mechanical anisotropy and formability of commercially pure titanium sheetwas investigated.Route A and Route B are unidirectional rolling(UR)where the rolling direction is along initial rolling direction(RD)and transverse direction(TD),respectively.Route C is cross rolling(CR)where the rolling direction is changed by90°aftereach rolling pass.The microstructure and texture,tensile mechanical properties including strength and elongation,and also theanisotropy of the UR and CR sheets were investigated at room temperature.The XRD results indicate that the texture intensity ofrolled samples gradually weakens from Route A to Route C.Compared with Route A and Route B rolled samples,the Route C rolledsamples show a smaller planar anisotropy.The deep drawing tests reveal that cross rolling can avoid the occurrence of earing.Erichsen tests indicate that rolling routes have an effect on stretch formability of pure titanium sheet.

Influence of heat treatment on microstructure and mechanical properties of FeCrNi coating produced by laser cladding

The FeCrNi alloy powders were used on the dovetail groove of FV520B steel to fabricate the multilayer laser cladding layers. The effects of heat treatment on the microstructure and mechanical properties of FeCrNi layers were investigated. The results showed that the heat treatment at the temperature ranged from 1073 to 1273 K refined the grains of the substrate materials and removed the soft zone of hardness between the fused zone (FZ) and base material (BM) effectively mainly due to a secondary quench of heat treatment. When the temperature of heat treatment was 1073 K, the maximum ultimate tensile strength (UTS) values of the laser cladding component were obtained. However, the heat treatment at high temperature had a bad effect on wear resistance of coatings at some extent.

Geometry Design and Tooth Contact Analysis of Crossed Beveloid Gears for Marine Transmissions

Beveloid gears,also known as conical gears,gain more and more importance in industry practice due to their abilities for power transmission between parallel,intersected and crossed axis.However,this type of gearing with crossed axes has no common plane of action which results in a point contact and low tooth durability.Therefore,a geometry design approach assuming line contact is developed to analyze the tooth engagement process of crossed beveloid gears with small shaft angle for marine transmission applications.The loaded gear tooth contact behavior is simulated by applying a quasi-static analysis to study the effects of gearing parameters on mesh characteristics.Using the proposed method,a series of sensitivity analyses to examine the effects of critical gearing parameters such as shaft angle,cone angle,helix angle and profile-shift coefficient on the theoretical gear mesh is performed.The parametric analysis of pitch cone design shows that the dominant design parameters represented by the angle between the first principle directions（FPD） and normal angular factor are more sensitive to the shaft and cone angles than they are to the helix angle.The theoretical contact path is highly sensitive to the profile-shift coefficient,which is determined from the theoretical tooth contact analysis.The FPD angle is found to change the distribution of contact pattern,contact pressure and root stress as well as the translational transmission error and the variation of the mesh stiffness significantly.The contact pattern is clearly different between the drive and coast sides due to different designed FPD angles.Finally,a practical experimental setup for marine transmission is performed and tooth bearing test is conducted to demonstrate the proposed design procedure.The experimental result compared well with the simulation.Results of this study yield a better understanding of the geometry design and loaded gear mesh characteristics for crossed beveloid gears used in marine transmission.

Microstructures and mechanical properties of AZ91D/0Cr19Ni9 bimetal composite prepared by liquid-solid compound casting

The liquid-solid compound casting technology was used to produce the AZ91D/0Cr19Ni9 bimetal composite without and with hot dipping aluminium, respectively. The influences of Al coating on microstructures and mechanical properties of AZ91D/0Cr19Ni9 interface were investigated. The results showed that the mechanical bonding was obtained between AZ91D and bare steel 0Cr19Ni9 where a gap existed at the interface; the metallurgical bonding was formed between AZ91D and Al-coated 0Cr19Ni9, which could be divided into two different intermetallic layers: layer Ⅰ was mainly composed of α-Mg+β-Mg17Al12 eutectic structure and a small amount of MgAl2O4, and layer Ⅱ mainly comprised of Fe2Al5 intermetallic compound. Furthermore, the hardness value of interface was obviously higher than that of AZ91D matrix, and the average hardness values of layers Ⅰ and Ⅱ were HV 158 and HV 493, respectively. The shear strength of AZ91D/Al-coated 0Cr19Ni9 interface was higher than that of AZ91D/bare 0Cr19Ni9 interface, which confirmed that Al coating could improve the adhesive strength between AZ91D and 0Cr19Ni9 during liquid-solid compound casting process.

Comparison of microstructures and mechanical properties of composite extruded AZ31 sheets

The microstructures and mechanical properties of the composite extruded AZ31/AZ31 and AZ31/4047 Al sheets were investigated and made a comparison to the conventional extruded AZ31 sheet.Owing to the introduced intense shear deformation at the interface during the composite extrusion,grain refinement and tilted texture were detected in AZ31 layers of the AZ31/AZ31 and AZ31/4047 Al sheets,while the conventional extruded AZ31 sheet exhibited a relative coarse,inhomogeneous microstructure and strong basal texture.The compressiontension yield ratio was increased gradually from the AZ31 to the AZ31/AZ31 and AZ31/4047 Al sheets.Besides,the AZ31/4047 Al sheet could successfully accomplish the whole bending forming process at room temperature,while the AZ31 and AZ31/AZ31 sheets were both bend-formed to failure with significant cracks in the outer tensile region under the identical bending parameters.Moreover,under the same bending strain,both the outward offset degree of strain neutral layer and the sheet thickening were more serious in the AZ31/4047 Al composite sheet than those of the AZ31 and AZ31/AZ31 sheets.The foremost reason was the quite wide gap of material properties between Mg alloy AZ31 layer(tensile loading in the outer region)and Al 4047 layer(compressive loading in the inner region).

Microstructures and mechanical properties of TC4/AZ91D bimetal prepared by solid-liquid compound casting combined with Zn/Al composite interlayer

To achieve Ti/Mg bimetallic composite with high strength and metallurgical bonding interface,Al interlayer and Zn/Al composite interlayer were used to prepare TC4/AZ91D bimetal composite with metallurgical bonding interface by solid-liquid compound casting,respectively.Al interlayer was prepared on the surface of TC4 alloy by hot dipping,and Zn/Al composite interlayer was prepared by electroplating process.The results suggested that the phases across the interface were Al Ti andα(Al)+Mg_(21)(Al,Zn)_(17)when Zn/Al composite interlayer was used.When Al interlayer was used as interlayer,Al Mg Ti ternary structure and Al_(12)Mg_(17)+δ-Mg eutectic structure were the main phases at the interface.The shear strength of TC4/AZ91D bimetal with Zn/Al composite interlayer was much higher than that with pure Al interlayer,and the value of the shear strength was increased from 48.5 to 67.4 MPa.Thermodynamic models based on different compositions of the interface were established to explain the microstructure evolution of the interfacial zone.

Optimization of mechanical and damping properties of Mg-0.6Zr alloy by different extrusion processing

In this study,the optimization of mechanical and damping capacities of Mg-0.6 wt.%Zr alloys by controlling the recrystallized(DRXed)grain size under varying extrusion processing parameters including extrusion temperature T and strain rate was investigated.The relationship between the DRXed grain size and damping properties of the studied alloy was also discussed.The DRXed grain size of the as-extruded Mg-Zr alloys decreased as the extrusion temperature T decreased and the strain rateεincreased.As the DRXed grain size decreased,the strength and elongation of the as-extruded alloys exhibited improved performance through the grain refinement mechanism,while the damping properties deteriorated.The extrusion temperature of the Mg-Zr alloy had relatively greater effects on the mechanical and damping properties than the strain rate.The results of the present work indicate that alloys with appropriate mechanical and damping properties may be obtained from controlling the DRXed grain size by careful tailoring of the extrusion process parameters.

Enhanced mechanical properties of Mg-3Al-1Zn alloy sheets through slope extrusion

A novel extrusion approach,entitled slope extrusion(SE),was employed to manufacture AZ31(Mg-3Al-1 Zn,wt%)alloy sheets.The microstructures,textures,and mechanical properties were investigated,compared with those of the AZ31 sheet fabricated by conventional extrusion(CE).Through the combination of finite element simulation and actual experiment,the ultimate results indicated that significant grain refinement(from 9.1 to 7.7 and 5.6μm)and strong basal texture(from 12.6 to 17.6 and 19.5 mrd)were achieved by the SE process.The essence was associated with the additional introduced inclined interface in the process of SE,which could bring about more asymmetric deformation and stronger accumulated strain along the ND when compared with the process of CE.As a consequence,the SE sheets exhibited a higher yield strength(YS)and ultimate tensile strength(UTS)than the counterparts of the CE sheet,which was mainly assigned to the synergistic effects from grain refining and texture strengthening.

Mechanical behaviors of cross roller bearings with raceway roundness error

Taking the raceway roundness error into account,mechanical characteristics of cross roller bearings(CRBs)were investigated.A static analysis model of CRBs considering the raceway roundness error was established.Based on this model,the rotational accuracy and load distribution of CRBs under constraints of geometry and external loads were derived.The fatigue life of CRBs with roundness error was calculated by applying Palmgren-Miner linear cumulative damage theory.The influence of inner and outer raceway roundness error on the performance of the CRBs,such as rotational accuracy,load distribution,and fatigue life,was studied through the analysis of examples.The results indicate that the influence of roundness error on the rotating inner raceway is more significant than that of roundness error on the nonrotating outer raceway.The roundness error on the rotating inner raceway always degrades the performance of CRBs.However,a proper roundness error on the nonrotating outer raceway can reduce the loads acting on the rollers and thus improve the fatigue life of CRBs.The effect of the roundness error amplitude on the bearing performance is ordinal,whereas the effect of the roundness order on the bearing performance is not in order.

Effect of Li content on microstructure and mechanical property of Mg-xLi-3(Al-Si) alloys

Mg-4 Li-3(Al-Si),Mg-8 Li-3(Al-Si)and Mg-12 Li-3(Al-Si)alloys based on theα-Mg,α-Mg+β-Li,β-Li phases,respectively,were produced to investigate the effect of alloying with Al-Si eutectic on the microstructure and mechanical properties of the three alloys.Alloying with the Al-Si eutectic of Mg-xLi(x=4,8 and 12 wt.%)alloys caused the formation of different types of Al-Li precipitates:Al3Li,AlLi and Li3Al2,respectively.Also,considerable quantities of Mg2Si phase particles were found in the three alloys.The results of tensile tests showed that the Mg-4Li-3(Al-Si)alloy exhibited the highest ultimate tensile strength(UTS)of 249 MPa but the lowest elongation of 6.3%.The Mg-12Li-3(Al-Si)alloy had the highest elongation of 26%but the lowest UTS of 173 MPa.The different mechanical properties were attributed to the different crystal structures of the three alloys and the precipitate with different type,morphology and distribution.

Effects of extrusion temperature on microstructure evolution and mechanical properties of heterogeneous Mg−Gd alloy laminates via accumulated extrusion bonding

The influence of extrusion temperature on microstructure and mechanical properties of heterogeneous Mg−1Gd/Mg−13Gd laminate prepared by accumulated extrusion bonding was investigated.The results reveal that the Mg−1Gd/Mg−13Gd laminate forms a significant difference in grain size between the successive layers when extruded at 330℃,and this difference gradually disappears as the extrusion temperature increases from 380 to 430℃.Besides,the growth rate of recrystallized grains in fine-grained layers is faster than that in coarse-grained layers.Moreover,the diffusion ability of Gd element increases with elevating extrusion temperatures,promoting the increase and coarsening of precipitates in fine-grained layers.Tensile tests indicate that the sample extruded at 380℃ has a superior combination of strength and ductility.This is mainly attributed to the synergy of the heterogeneous texture between coarse and fine-grained layers,hetero-deformation induced strengthening and hardening.The fine-grained layers facilitate the activation of prismaticáañslips,while coarse-grained layers make it easier to active basaláañand pyramidalác+añslips,especially for the sample extruded at 380℃.The activation of pyramidalác+añslips contributes to coordinating further plastic deformation.

Effects of graphene nanoplates on microstructures and mechanical properties of NSA-TIG welded AZ31 magnesium alloy joints

The effects of graphene nanoplates(GNPs)on the microstructures and mechanical properties of nanoparticlesstrengthening activating tungsten inert gas arc welding(NSA-TIG)welded AZ31magnesium alloy joints were investigated.It wasfound that compared with those of activating TIG(A-TIG),and obvious refinement ofα-Mg grains was achieved and the finestα-Mggrains of fusion zone of NSA-TIG joints were obtained in the welded joints with TiO2+GNPs flux coating.In addition,thepenetrations of joints coated by TiO2+GNPs flux were similar to those coated by the TiO2+SiCp flux.However,the welded jointswith TiO2+GNPs flux coating showed better mechanical properties(i.e.,ultimate tensile strength and microhardness)than those withTiO2+SiCp flux coating.Moreover,the generation of necking only occurred in the welded joints with TiO2+GNPs flux.

Three-Dimensional Conjugate Tooth Surface Design and Contact Analysis of Harmonic Drive with Double-Circular-Arc Tooth Profle

A three-dimensional conjugate tooth surface design method for Harmonic Drive with a double-circular-arc tooth profle is proposed. The radial deformation function of the fexspline (FS), obtained through Finite Element (FE) analysis, is incorporated into the kinematics model. By analyzing the FS tooth enveloping process, the optimization of the overlapping conjugate tooth profle is achieved. By utilizing the hobbing process, the three-dimensional machinable tooth surface of FS can be acquired. Utilizing the coning deformation of the FS, simulations are conducted to analyze the multi-section assembly and meshing motion of the machinable tooth surface. The FE method is utilized to analyze and compare the loaded contact characteristics. Results demonstrate that the proposed design method can achieve an internal gear pair consisting of a circular spline with a spur gear tooth surface and the FS with a machinable tooth surface. With the rated torque, approximately 24% of the FS teeth are engaged in meshing, and more than 4/5 of the tooth surface in the axial direction carries the load. The contact patterns, maximum contact pressure, and transmission error of the machinable tooth surface are 227.2%, 40.67%, and 71.24% of those on the spur gear tooth surface, respectively. It clearly demonstrates exceptional transmission performance.

Design of Linear Functional Noncircular Gear with High Contact Ratio Used in Continuously Variable Transmission

Continuously variable transmission(CVT)of noncircular gear has the technical advantages of large bearing capacity and high transmission efficiency.The key technology of CVT with noncircular gear has been broken through some countries,and is in the stage of deep application research.Although the characteristics and design methods of noncircular gear pairs have been continuously studied in China,the noncircular gear CVT is still in the preliminary exploration and research stage.The linear functional noncircular gear pair,whose transmission ratio is a linear function in the working section,to realize continuously variable transmission was the research object in this paper.According to the required transmission ratio in the working section,the transmission ratio function in the non-working section was constructed by using a polynomial.And then the influence of pitch curve parameters in the working section on which in the non-working section was also analyzed to obtain the pitch curve suitable for transmission of this gear pair.In addition,for improving the stability and bearing capacity of gear transmission,the noncircular gear pair transmission with high contact ratio was designed.Furthermore,the accurate value of the contact tooth length was calculated based on the gear principle and the characteristics of the involute tooth profile,from this the contact tooth length error was calculated by comparing the accurate value with its actual value obtained by the rolling experiment.Finally,an indirect method to verify the contact ratio by detecting the contact length error of the tooth profile was proposed.

On Energy Assessment of Titanium Alloys Belt Grinding Involving Abrasive Wear Effects

Improved energy utilisation,precision,and quality are critical in the current trend of low-carbon green manufactur-ing.In this study,three abrasive belts were prepared at various wear stages and characterised quantitatively.The effects of abrasive belt wear on the specific grinding energy partition were investigated by evaluating robotic belt grinding of titanium plates.A specific grinding energy model based on subdivided tangential forces of cutting and sliding was developed for investigating specific energy and energy utilisation coefficient EUC.The surface mor-phology and Abbott–Firestone curves of the belts were introduced to analyse the experimental findings from the per-spective of the micro cutting behaviour.The specific grinding energy increased with abrasive belt wear,especially when the belt was near the end of its life.Moreover,the belt wear could lead to a predominance change of sliding and chip formation energy.The highest EUC was observed in the middle of the belt life because of its retained sharp cutting edge and uniform distribution of the grit protrusion height.This study provides guidance for balancing the energy consumption and energy utilization efficiency of belt grinding.

A Multi-mode Electronic Load Sensing Control Scheme with Power Limitation and Pressure Cut-off for Mobile Machinery

In mobile machinery,hydro-mechanical pumps are increasingly replaced by electronically controlled pumps to improve the automation level,but diversified control functions(e.g.,power limitation and pressure cut-off)are integrated into the electronic controller only from the pump level,leading to the potential instability of the overall system.To solve this problem,a multi-mode electrohydraulic load sensing(MELS)control scheme is proposed especially considering the switching stability from the system level,which includes four working modes of flow control,load sensing,power limitation,and pressure control.Depending on the actual working requirements,the switching rules for the different modes and the switching direction(i.e.,the modes can be switched bilaterally or unilaterally)are defined.The priority of different modes is also defined,from high to low:pressure control,power limitation,load sensing,and flow control.When multiple switching rules are satisfied at the same time,the system switches to the control mode with the highest priority.In addition,the switching stability between flow control and pressure control modes is analyzed,and the controller parameters that guarantee the switching stability are obtained.A comparative study is carried out based on a test rig with a 2-ton hydraulic excavator.The results show that the MELS controller can achieve the control functions of proper flow supplement,power limitation,and pressure cut-off,which has good stability performance when switching between different control modes.This research proposes the MELS control method that realizes the stability of multi-mode switching of the hydraulic system of mobile machinery under different working conditions.

Model of Surface Texture for Honed Gear Considering Motion Path and Geometrical Shape of Abrasive Particle

Gear power-honing is mainly applied to finish small and medium-sized automotive gears,especially in new energy vehicles.The distinctive curved surface texture greatly improves the noise emission and service life of honed gears.The surface texture for honed gear considering the motion path and geometrical shape of abrasive particles has not been investigated.In this paper,the kinematics of the gear honing process is analyzed,and the machining marks produced by the abrasive particles of honing wheel scratching abrasive particles against the workpiece gear are calculated.The tooth surface roughness is modeled considering abrasive particle shapes and material plastic pile-ups.This results in a mathematical model that characterizes the structure of the tooth surface and the orientation of the machining marks.Experiments were used to verify the model,with a maximum relative error of less than 10%when abrasive particles are spherical.Based on this model,the effects of process parameters on the speeds of discrete points on the tooth flank,orientations of machining marks and roughness are discussed.The results show that the shaft angle between the workpiece gear and the honing wheel and the speed of the honing wheel is the main process parameters affecting the surface texture.This research proposes a surface texture model for honed gear,which can provide a theoretical basis for optimizing process parameters for gear power-honing.

Surface reconstruction,modification and functionalization of natural diatomites for miniaturization of shaped heterogeneous catalysts

Since the discovery of mesoporous silica in 1990s,there have been numerous mesoporous silica-based nanomaterials developed for catalytic applications,aiming at enhanced catalytic activity and stability.Recently,there have also been considerable interests in endowing them with hierarchical porosities to overcome the diffusional limitation for those with long unimodal channels.Present processes of making mesoporous silica largely rely on chemical sources which are relatively expensive and impose environmental concerns on their processes.In this regard,it is desirable to develop hierarchical silica supports from natural minerals.Herein,we present a series of work on surface reconstruction,modification,and functionalization to produce diatomite-based catalysts with original morphology and macro-meso-micro porosities and to test their suitability as catalyst supports for both liquid-and gas-phase reactions.Two wet-chemical routes were developed to introduce mesoporosity to both amorphous and crystalline diatomites.Importantly,we have used computational modeling to affirm that the diatomite morphology can improve catalytic performance based on fluid dynamics simulations.Thus,one could obtain this type of catalysts from numerous natural diatoms that have inherently intricate morphologies and shapes in micrometer scale.In principle,such catalytic nanocomposites acting as miniaturized industrial catalysts could be employed in microfluidic reactors for process intensification.

Strength-ductility balance of AZ31 magnesium alloy via accumulated extrusion bonding combined with two-stage artificial cooling Author links open overlay panel

AZ31 Mg alloy with heterogeneous bimodal grain structure(smaller grain size of 5-20µm and coarser grain size of 100-200µm)was subjected to accumulated extrusion bonding(AEB)at 250℃combined with two-stage artificial cooling in this work,viz.local water cooling and artificial cooling.The microstructure developed consecutively as a result of discontinuous dynamic recrystallization(DDRX)for the AEBed samples.{10-12}tensile twinning also played an important role for the AEB with local water cooling at the initial extrusion stage in the container.Local water cooling could further reduce the DRXed grain size to~2.1µm comparing that without water cooling.And the grain growth rate was reduced by artificial cooling out of extrusion die.Under the combination of two-stage cooling,the fine DRXed grains at sizing band were almost retained with average grain size of~2.3µm after the sheet out of extrusion die,and the unDRXed grains with high residual dislocation density accumulation were also reserved.The tensile tests results indicated that a good strength-ductility balance with a high ultimate tensile strength(319 MPa vs.412 MPa)and fracture elongation(19.9%vs.30.3%)were obtained.The strength enhancement was mainly owing to the grain refinement and local residual plastic strain reserved by the artificial cooling.The excellent ductility originated from fine DRXed microstructure and ED-tilt double peak texture.