Precipitation process and its effects on properties of aging Cu–Ni–Be alloy

The precipitation process of aged Cu-Ni-Be alloy was investigated by X-ray diffraction （XRD）, trans- mission electron microscopy （TEM）, and high-resolution transmission electron microscopy （HRTEM）. The tensile strength, yield strength, and electronic conductivity of this alloy after aging were also studied. The precipitation sequence of the C17510 alloy aged at 525 ℃ is supersat-urated solid solution→G.P zones→ γ″-γ′→ γ. This transformation can be achieved by the accumulation of Be-atom layers. The G.P zones are composed of disk-shaped monolayers of Be atoms, which are formed on （001） matrix planes. The intermediate γ″ precipitate is nucleated in the G.P zones. The γ″ and γ′ precipitates have the same orientation relationship with matrix, e.g., （110）p｜｜（100）M,[001]p｜｜[001]M. The tensile strength of specimen shows a maximum during the aging process and then continuously decreases if the specimen is over aged. The strengthening effect of γ′ phase precipitated in aging at 525 ℃ for 4 h is calculated to be 436 MPa according to the Orowan strengthening, which is quite consistent with the experimental data.

Tensile and fracture properties of Ti-62A alloy plate with different microstructures

Ti-62A alloy plates with three different types of microstructure, fully equiaxed, bimodal, and Widmanstatten, were obtained by various heat treatments to investigate the effects of microstructure on the tensile and fracture properties at room temperature. The results reveal that Widmanstatten microstructure exhibits good damage tolerance behavior considering strength, fracture toughness, and fatigue crack growth behavior, while the bimodal microstructure shows good comprehensive properties considering the plasticity synthetically. Optical microscopy (OM) and scanning electron microscopy (SEM) microstructure analyses on fracture and fatigue crack path demonstrate that the dependence of mechanical properties and fatigue crack growth behavior on microstructural feature are attributed to the α lamellae width and the α colony size. © The Nonferrous Metals Society of China and Springer-Verlag Berlin Heidelberg 2012.

Hot deformation behavior and globularization mechanism of Ti-6Al-4V-0.1B alloy with lamellar microstructure

Hot deformation behavior and globularization mechanism of Ti6A14V0.1B alloy with lamellar micro structure were quantitatively studied through isothermal compression tests with the temperature range of 850950 ℃and strain rate range of 0.011.00 s1. The results show that the peak flow stress and steady stress are sensitive to the strain rate and temperature. The value of deformation activation energy is 890.49 kJmo11 in （a＋β） region. Dynamic recrystallization is the major deformation mecha nism. Flow softening is dominated by dynamic recrystallization at 850950 ℃. TiB particles promote the recrystallization of laths. Globularization processes consist of four steps： for mation of subgrain after dynamic recovery in a plates; subgrain boundary migration caused by interracial instability; interfacial migration promoting phase wedge into a phase; disintegrating of a laths by diffusion processes; and grain boundary sliding. Globularization mechanisms during hot deformation processes of the Ti6A14V0.1B alloy with lamellar structure are continuous dynamic recrystallization.

Microstructure and tensile properties of isothermally forged Ni–43Ti–4Al–2Nb–2Hf alloy

NiTi-Al-based alloys are promising high-tem- perature structural materials for aerospace and astronautics applications. A new NiTi-Al-based alloy Ni--43Ti-4AI- 2Nb-2Hf （at%） was processed via isothermal forging. The microstructure and mechanical properties at room temperature and high temperature were investigated through scanning electron microscope （SEM）, X-ray diffraction （XRD）, and tensile tests. Results show that the micro- structure of as-forged Ni-43Ti--4AI-2Nb-2Hf alloy con- sists of NiTi matrix, Ti2Ni phase, and Hf-rich phase. The simultaneous addition of Nb and Hf, which have strong affinities for Ti sites, promotes the precipitation of Hf-rich phases along the grain boundaries. The tensile strengths of Ni-43Ti-4A1-2Nb-2Hf alloy are dramatically increased compared with the ternary Ni-46Ti-4A1 alloy. At room temperature and 650℃, the yield stress of Ni--43Ti-4Al- 2Nb-2Hf alloy reaches 1,070 and 610 MPa, respectively, which are 30 % and 150 % higher than those of Ni--46Ti- 4Al alloy. The improved tensile property results from the solid solution strengthening by Nb and Hf, as well as the dispersion hardening of the Ti2Ni and Hf-rich phases.

Mechanical properties and microstructure of rolled and electrodeposited thin copper foil

Commercial grade rolled and electrodeposited copper foils from Japan and China were selected, and their mechanical properties and microstructure were investigated. It was observed that there are notable differences in fracture strength, elongation at break and hydrophilicity between rol- led and electrodeposited copper foils. The rolled copper foils have higher tensile strength, lower ductility and larger static contact angle than electrodeposited copper foils. The rolled copper foils contain a [^-fiber texture, and the electrodeposited copper foils have random crystalline orientations. It was also observed that the rolled foils have packed grains, and elec- trodeposited foils have equiaxial grains. The uniform fine grain size and a few substructures of Japanese electrode- posited foils are major reasons for their higher elongation.