Research on submerged arc welding wire for X100 pipeline steel

According to the study of the microstructure and properties of X100 pipeline steel, the welding consumable-wire based on Mn-Ni-Mo-B-Ti alloy system was successfully designed and developed. The yield strength of the deposited metal of the developed welding wire was 695 MPa, the tensile strength was 810 MPa, and Charpy impact energy was 92 J at negative 20 ℃ when matching with BSG-SJ101H1 sintered flux. The results of the weldability test for X100 pipeline steel which adopting this developed wire showed that the tensile strength of the weld was 827 MPa, 185 J of Charpy impact energy（ -10 ℃ ） , 97% of section of shear and the weld had good strength and toughness matching when the welding speed got to 1.7 m/min. The microstructure and fracture appearance of the weld were analyzed by using metallographic microscope, scanning electron microscope （SEM） and laser confocal microscope, the results indicated that the microstructure was mainly granular bainite in the weld metal, and the fracture was dimple with 200 - 300 μm depth presenting a typical ductile fracture characteristics. The test of welding wire with different content of Ni and Cr element indicated that Ni was better than Cr in improving the strength and toughness of weld metal.

An in-situ study of static recrystallization in Mg using high temperature EBSD

It has been a common method to improve the mechanical properties of metals by manipulating their microstructures via static recrystallization,i.e.,through heat treatment.Therefore,the knowledge of recrystallization and grain growth is critical to the success of the technique.In the present work,by using in-situ high temperature EBSD,the mechanisms that control recrystallization and grain growth of an extruded pure Mg were studied.The experimental results revealed that the grains of priority for dynamic recrystallization exhibit fading competitiveness under static recrystallization.It is also found that grain boundary movement or grain growth is likely to show an inverse energy gradient effect,i.e.,low energy grains tend to swallow or grow into high energy grains,and grain boundaries of close to 30°exhibit superior growth advantage to others.Another finding is that{10-12}tensile twin boundaries are sites of hardly observed for recrystallization,and are finally swallowed by adjacent recrystallized grains.The above findings may give comprehensive insights of static recrystallization and grain growth of Mg,and may guide the design of advanced materials processing in microstructural engineering.

Online Monitoring of Welding Status Based on a DBN Model During Laser Welding

In this research,an auxiliary illumination visual sensor system,an ultraviolet/visible(UVV)band visual sensor system(with a wavelength less than 780 nm),a spectrometer,and a photodiode are employed to capture insights into the high-power disc laser welding process.The features of the visible optical light signal and the reflected laser light signal are extracted by decomposing the original signal captured by the photodiode via the wavelet packet decomposition(WPD)method.The captured signals of the spectrometer mainly have a wavelength of 400-900 nm,and are divided into 25 sub-bands to extract the spectrum features by statistical methods.The features of the plume and spatters are acquired by images captured by the UVV visual sensor system,and the features of the keyhole are extracted from images captured by the auxiliary illumination visual sensor system.Based on these real-time quantized features of the welding process,a deep belief network(DBN)is established to monitor the welding status.A genetic algorithm is applied to optimize the parameters of the proposed DBN model.The established DBN model shows higher accuracy and robustness in monitoring welding status in comparison with a traditional back-propagation neural network(BPNN)model.The effectiveness and generalization ability of the proposed DBN are validated by three additional experiments with different welding parameters.

YAG laser welding with surface activating flux

YAG laser welding with surface activating flux has been investigated, and the influencing factors and mechanism are discussed. The results show that both surface activating flux and surface active element S have fantastic effects on the YAG laser weld shape, that is to obviously increase the weld penetration and D/W ratio in various welding conditions. The mechanism is thought to be the change of weld pool surface tension temperature coefficient, thus, the change of fluid flow pattern in weld pool due to the flux.

Study of Dynamic Features of Surface Plasma in High-Power Disk Laser Welding

High-speed photography was used to obtain the dynamic changes in the surface plasma during a high-power disk laser welding process. A color space clustering algorithm to extract the edge information of the surface plasma region was developed in order to improve the accuracy of image processing. With a comparative analysis of the plasma features, i.e., area and height, and the characteristics of the welded seam, the relationship between the surface plasma and the stability of the laser welding process was characterized, which provides a basic understanding for the real-time monitoring of laser welding.

Comparative study on evaluation of tendon force for welding distortion prediction in thin plate fabrication

Tendon force is an essential concept to predict welding distortion such as longitudinal shrinkage and welding induced buckling in thin plate fabrication. In this study,three approaches with experimental,theoretical and computational analysis,are examined to evaluate the magnitude of tendon force. In detail,inherent deformation theory is introduced first,the theoretical analysis to obtain the inherent strain solution is also reviewed; and then analytical solution for tendon force is achieved. Also,the theory of FE analysis for welding is introduced and implemented in a computation to obtain the transient temperature distribution,plastic strain,residual stress and welding distortion in a bead-on-plate welded joint with 2. 28 mm in thickness. The longitudinal displacement is employed to evaluate tendon force directly,and these computed inherent strain and inherent stress can also be employed to evaluate tendon force by integration approach later. All the evaluated magnitudes of tendon force have a good agreement with each other.

Time Dependant Weld Shape in Ar-O_2 Shielded Stationary GTA Welding

The stationary gas tungsten arc welding （GTA） is carried out on SUS304 stainless steel under Ar-0.1%O2 and Ar-0.3%O2 mixed shielding to observe the evolution of the molten pool and investigate the role of Marangoni convection on the weld shape. After welding, the oxygen content in the weld metal was measured by using an oxygen/nitrogen analyzer. Small addition of oxygen to the argon based shielding gas can effectively adjust the weld pool oxygen content. Oxygen plays an important role as an surface active element in determining the pattern of Marangoni convection in the stainless steel weld pool. When the weld metal oxygen content is over the critical value, 0.01 wt pct, corresponding to the Ar-0.3%O2 mixed shielding gas, the Marangoni convection changes from outward to inward direction and the weld shape dramatically changes from wide shallow shape to narrow deep shape.

Development of Evaluation Technique of GMAW Welding Quality Based on Statistical Analysis

Nondestructive techniques for appraising gas metal arc welding（GMAW） faults plays a very important role in on-line quality controllability and prediction of the GMAW process. On-line welding quality controllability and prediction have several disadvantages such as high cost, low efficiency, complication and greatly being affected by the environment. An enhanced, efficient evaluation technique for evaluating welding faults based on Mahalanobis distance（MD） and normal distribution is presented. In addition, a new piece of equipment, designated the weld quality tester（WQT）, is developed based on the proposed evaluation technique. MD is superior to other multidimensional distances such as Euclidean distance because the covariance matrix used for calculating MD takes into account correlations in the data and scaling. The values of MD obtained from welding current and arc voltage are assumed to follow a normal distribution. The normal distribution has two parameters： the meanm and standard deviations of the data. In the proposed evaluation technique used by the WQT, values of MD located in the range from zero tom＋3s are regarded as “good”. Two experiments which involve changing the flow of shielding gas and smearing paint on the surface of the substrate are conducted in order to verify the sensitivity of the proposed evaluation technique and the feasibility of using WQT. The experimental results demonstrate the usefulness of the WQT for evaluating welding quality. The proposed technique can be applied to implement the on-line welding quality controllability and prediction, which is of great importance to design some novel equipment for weld quality detection.

Optimisation of laser welding parameters for welding of P92 material using Taguchi based grey relational analysis

Creep strength enhanced ferritic(CSEF) steels are used in advanced power plant systems for high temperature applications. P92(Cr–W–Mo–V)steel, classified under CSEF steels, is a candidate material for piping, tubing, etc., in ultra-super critical and advanced ultra-super critical boiler applications. In the present work, laser welding process has been optimised for P92 material by using Taguchi based grey relational analysis(GRA).Bead on plate(BOP) trials were carried out using a 3.5 k W diffusion cooled slab CO_2 laser by varying laser power, welding speed and focal position. The optimum parameters have been derived by considering the responses such as depth of penetration, weld width and heat affected zone(HAZ) width. Analysis of variance(ANOVA) has been used to analyse the effect of different parameters on the responses. Based on ANOVA, laser power of 3 k W, welding speed of 1 m/min and focal plane at-4 mm have evolved as optimised set of parameters. The responses of the optimised parameters obtained using the GRA have been verified experimentally and found to closely correlate with the predicted value.? 2016 China Ordnance Society. Production and hosting by Elsevier B.V. All rights reserved.

Quasi-in-situ investigation into the microstructure and texture evolution of pure magnesium during friction stir welding

The quasi-in-situ microstructure and texture evolution along the real flow path of pure magnesium during friction stir welding were investigated.Five representative stages were involved from the base metal to the formation of the final stir zone.The material experienced compression,preheating,acceleration,deceleration,and subsequent annealing over the course of the welding process.A highly concentrated(0001)texture,denoted as''orientation convergence^,was initiated at the beginning of the acceleration stage(shearing deformation zone)in front of the tool.Both continuous and discontinuous dynamic recrystallization occurred simultaneously in the stir zone,and continuous dynamic recrystallization was determined to be the primary recrystallization mechanism.The marker material morphology and EBSD data were used to elucidate the in-situ evolution of the shear direction and shear plane along with the real flow path.

Comparative study on transverse shrinkage, mechanical and metallurgical properties of AA2219 aluminium weld joints prepared by gas tungsten arc and gas metal arc welding processes

Aluminium alloy AA2219 is a high strength alloy belonging to 2000 series. It has been widely used for aerospace applications, especially for construction of cryogenic fuel tank. However, arc welding of AA2219 material is very critical. The major problems that arise in arc welding of AA2219 are the adverse development of residual stresses and the re-distribution as well as dissolution of copper rich phase in the weld joint.These effects increase with increase in heat input. Thus, special attention was taken to especially thick section welding of AA2219-T87 aluminium alloy. Hence, the present work describes the 25 mm-thick AA2219-T87 aluminium alloy plate butt welded by GTAW and GMAW processes using multi-pass welding procedure in double V groove design. The transverse shrinkage, conventional mechanical and metallurgical properties of both the locations on weld joints were studied. It is observed that the fair copper rich cellular(CRC) network is on Side-A of both the weldments. Further, it is noticed that, the severity of weld thermal cycle near to the fusion line of HAZ is reduced due to low heat input in GTAW process which results in non dissolution of copper rich phase. Based on the mechanical and metallurgical properties it is inferred that GTAW process is used to improve the aforementioned characteristics of weld joints in comparison to GMAW process.

Pulsed current and dual pulse gas metal arc welding of grade AISI: 310S austenitic stainless steel

The transverse shrinkage, mechanical and metallurgical properties of AISI: 310 S ASS weld joints prepared by P-GMAW and DP-GMAW processes were investigated. It was observed that the use of the DP-GMAW process improves the aforementioned characteristics in comparison to that of the P-GMAW process. The enhanced quality of weld joints obtained with DP-GMAW process is primarily due to the combined effect of pulsed current and thermal pulsation(low frequency pulse). During the thermal pulsation period, there is a fluctuation of wire feed rate,which results in the further increase in welding current and the decrease in arc voltage. Because of this synchronization between welding current and arc voltage during the period of low frequency pulse, the DP-GMAW deposit introduces comparatively more thermal shock compared to the P-GMAW deposit, thereby reducing the heat input and improves the properties of weld joints.

Analysis of Laser-Induced Plume During Disk Laser Welding at Different Speeds

During high power disk laser welding, the high-speed photography was used to measure the dynamic images of the laser-induced plume at different laser welding speeds. Various plume features （area, height and brightness） were extracted from the images by the color space clustering algorithm. Combined with observation on the surface and the cross sections of welding samples, the effect of welding speed on welding stability was analyzed. From the experimental results, it was found that these features of plume could reflect the welding state. Thus changes of the plume features corresponded to different welding speeds, which was helpful for monitoring the laser welding stability.

Influence of Flux and Sulfur on YAG Laser Welding

The influence of flux and sulfur content on YAG laser welding has been investigated, and the influencing factors and mechanism were discussed. The results show that both surface activating flux and surface active element S have fantastic effects on the YAG laser weld shape, that is to obviously increase the weld penetration and D/W ratio in various welding conditions. The mechanism is thought to be the change of surface tension temperature coefficient in weld pool, thus, the change of fluid flow paten in weld pool due to the flux and sulfur.

Impact Strength Analysis of Plate Panels with Welding-Induced Residual Stress and Deformation

The paper describes the simulation of impact loads applied on plate panels with welding-induced residual stresses and deformation (WSD). Numerical simulations using FEM are carried out to study the influence of welding-induced residual stresses and deformation on the impact strength of plate panels. Welding is simulated using a three dimensional thermal mechanical coupled finite element method. The welding stress and deformation are taken as the initial imperfections in the impact strength analysis and their influence on the behavior of plate panels subjected to impact loadings. The impact loadings from the three directions, the lateral direction and two in-plane directions of the plate panels are studied. Results show a certain reduction in the impact strength due to the existence of welding stress and deformation in the plate panels. It is found that the reduction of impact force is strongly influenced by the welding deformation and the impact directions in the plate panels. This reduction is more significant when the impact force is in the lateral direction.

Effect of Gravity on Arc Shape in GTA Welding-for Low Electric Arc Current

Gas tungsten arc (GTA) welding was performed both in a microgravity environment and in a terrestrial environment,and the arc shapes in both environments were compared. A microgravity condition was obtained using the free fallsystem at the Japan Microgravity Center. The system can maintain a 10 s microgravity of less than 10-5 g. Awater-cooled Cu plate was used to simplify the arc phenomenon. The electric arc current was between 15 and 80 A,and the shielding and atmospheric gas was 99.9995% Ar and its flowing rate was 10 l/min. The polarity was a directcurrent electrode negative (DCEN). The arc gap was 3 mm and careful attention was also paid to the arc gap in boththe terrestrial and microgravity environments being the same. As a result, it was found that no effect of gravity onthe arc shape is observed under general welding conditions (over 60 A). When the electric arc current is lower than25 A, the arc shape is determined by the initial position of the arc root and is constant with time. Accordingly, itcan not be judged whether or not the arc shape is affected by gravity for this range. When the electric arc current isbetween 25 A and 60 A, it is estimated that the arc shape is not affected by gravity though it is occasionally affectedby other minor effects.

Friction stir welding characteristics of two aluminum alloys

The friction stir welding characteristics of the strain hardened AA1050 H24 and precipitate hardened AA2017 T351 aluminum alloys were examined in order to reveal the effects of the alloy properties on the friction stir welding behavior of the base materials. The results show that (1) for AA1050 H24, the weld possesses a smooth surface and clear ripples, there is no elliptical weld nugget in the weld, there is not discernible interface between the stir zone and the thermo mechanically affected zone(TMAZ), and the internal defect of the weld looks like a long crack and is located in the lower part of the weld; (2) for AA2017 T351, the weld usually possesses a rough surface and visible ripples, the elliptical weld nugget clearly exists in the weld and there is obvious plastic flow and a discernible interface between the nugget and the TMAZ, and the internal defect of the weld is composed of many voids and distributed in the middle part of the weld; (3) the effective ranges of the welding parameters for AA1050 H24 and AA2017 T351 are both narrow, especially for the latter; and (4) the tensile strength efficiencies of the joints for the two typical alloys are similar, i e 79% for AA1050 H24 and 82% for AA2017 T351.

Effect of Welding Parameters on GTA Weld Shape for Pure Iron Plate under Ar-O_2 Mixed Shielding

Weld shape variation for different welding parameters is investigated on pure iron plate under gas tungsten arc （GTA） welding with argon-oxygen mixed shielding. Results showed that small addition of oxygen to the argon base shielding gas can effectively adjust the oxygen adsorption to the molten pool. An inward Marangoni convection occurs on the pool surface when the oxygen content in the weld pool is over the critical value, 80×10^-6, for pure iron plate under Ar-0.3%O2 mixed shielding. Low oxygen content in the weld pool changes the inward Marangoni to an outward direction under the Ar-0.1%O2 shielding. The GTA weld shape depends to a large extent on the pattern and strength of the Marangoni convection on the pool surface, which is determined by the content of surface active element, oxygen, in the weld pool and the welding parameters. The strength of the Marangoni convection on the liquid pool is a product of the temperature coefficient of the surface tension （dσ/dT） and the temperature gradient （dT/dr） on the pool surface. Different welding parameters will change the temperature distribution and gradient on the pool surface, and therefore, affect the strength of Marangoni convection and the weld shape.

Prediction of cooling time t8/5 in twin wire submerged arc welding of intermediate thickness plate

Twin wire submerged arc welding （SAW） is widely used in oil or gas line pipe fabrication because of its high productivity. To investigate the strength and toughness of the heat-affected zone （HAZ） in twin wire SAW, the cooling time t8/5 of the coarse grained zone must be studied. The authors presented a method of predicting the cooling time in twin wire SAW of intermediate thickness plate. Based on Rosenthal analytical solutions, an energy factor was introduced to describe the energy contribution of the two wires, equations of thermal cycle and cooling time in twin wire SAW of both thick, and thin, plates were developed. Weighting factors determined by actual thickness and critical thickness were adopted to represent the thermal cycle and cooling time of intermediate thickness plate through linear interpolation with thick, and thin, plate solutions. The predicted cooling time for an intermediate thickness plate was verified experimentally, and the predicted results agreed therewith.

Numerical Simulation of Molten Metal Droplet Behavior in Gas Metal Arc Welding by Three-Dimensional Incompressible Smoothed Particle Hydrodynamics Method

The numerical model was developed using a SPH (Smoothed Particle Hydrodynamics) method and the projected transfer phenomena during a GMA (Gas Metal Arc) welding were simulated by the model to clarify mechanisms of the phenomena. As a result, the droplet transfer mode obtained from this calculation was regarded as a projected transfer mode in which the liquid column grew about 1 mm and a droplet grew up until its diameter became large the same as a wire diameter,?after that it was detached from the tip of the column. In addition, 10 droplets were formed for 0.1 s through these growth and detachment processes at the tip of a wire. To compare with the numerical results, actual GMA welding was carried out and molten metal droplet transfers were taken by high speed camera. The diameter of a wire, the length of a liquid column, the velocity of a droplet right before it reached a weld pool obtained by simulation showed good agreement with experiment.