Analysis and results to the status of BIM technology application in China

Information age and the rapid development of information technology has brought the infinite creativity and possibility for all works in modem society. If CAD technology is first innovation of information technology in construction industry, then the emergence of the BIM technology shall fully deserved to be treated as a second innovation in construction industry. As a new technology which have been introduced to China in recent years, BIM technology already had its major application in foreigner countries .This paper focuses on the current status of BIM technology application in our country, especially on some small and medium enterprises using the traditional BIM technology to handle the project which have complex usage,creative deign and cost limitation. Firstly,we take a deep analysis on the initial application situation. Then we go through the practical application and analyse what benefit can be given to a project from BIM technology. Finally, analyse the problems and solutions in BIM application with consideration of Chinese building engineering development. Only after a careful analysis, a deep understanding of BIM, we can fully understand this new technology and make BIM to give its value to construction project.

Dynamic management system of ore blending in an open pit mine based on GIS/GPS/GPRS

Using GIS, GPS and GPRS, a dynamic management system of ore blending in an open pit mine has been designed and developed. A linear program was established in a practical application. The system is very good at automatically drawing up a daily production plan of ore blending and monitors and controls the process of mining production in real time. Experiments under real conditions show that the performance of this system is stable and can satisfy production standards of ore blending in open pit mines.

Batch methanogenic fermentation experiments of wastewater from a brown coal low-temperature coke plant

Coke plant effluents with high contents of organic compounds are mainly treated by biological aerobic fermentation after physical pre-treatment. In this study, a brown coal condensate wastewater from a low temperature coking process was fermented under methanogenic conditions in discontinuous experiments. By this fermentation, acetate, propionate, and the main polyphenolic compounds （catechol, resorcinol and hydroquinone） were degraded to a level below the detection limit. The COD was reduced by 72% with a residual concentration of 2.1 g/L. This anaerobic fermented wastewater had a residual BOD5 of 0.66 g/L and 2.2 L CH4 were formed per litre of wastewater. An abiotic pre-treatment for this wastewater with air had a negative effect on the COD reduction and decrease of colour on the methanogenic fermentation due to the autoxidation of polyphenolic compounds to humic-like compounds. This study showed that methanogenic fermentations in the treatment sequence of brown coal coking wastewaters could reduce energy consumption for aeration in further treatment processes and had the potential for a better effluent quality due to a less formation of recalcitrant humic-like compounds.

Preparation of Sialon Powder from Coal Gasification Slag

X-ray fluorescence spectrometry（XRF）,X-ray powder diffractometry（XRD） and scanning electron microscopy（SEM） were used to characterize the chemical composition,phase constituent and microstructure of the coal gasification slag.Sialon powders were synthesized by carbothermal reduction and nitridation using the coal gasification slag as raw materials.The experimental results showed that glass and amorphous carbon were the main phases,quartz and calcite as minor crystalline phases were also presented in porous coal gasification slag.Main constituents of coal gasification slag were SiO2,Al2O3,CaO and residual carbon.Sialon powder with Ca-α-Sialon as main crystalline phase can be synthesized when coal gasification slag powders were reduced and nitrided at 1500 ℃ for 9 h using nitrogen flow of 500 ml/min.The coal gasification slag is a valuable and economic starting material for preparing Sialon powders.

Multilayer Clad Plate of Stainless Steel/Aluminum/ Aluminum Alloy

The 3, 5, 20 layer clad plate from austenitic stainless steel, pure aluminum and aluminum alloy sheets were fabricated in different ways. The stretch and interface properties were measured. The result shows that 20 layer clad plate is better than the others. Well-bonded clad plate was successfully obtained in the following procedure： Basic clad sheet from 18 layer Al1060/Al3003 sheets was firstly obtained with an initial rolling reduction of 44% at 450 ℃, followed by annealing at 300 ℃, and then with reduction of 50% at 550 ℃ from STS304 on each side. The best 20 layer clad plate was of 129 MPa bonding strength and 225 MPa stretch strength.

Spheroidization of molybdenum powder by radio frequency thermal plasma

To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency（RF） plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in this paper. The effects of the carrier gas flow rate and molybdenum powder feeding rate on the shape and size of the final products were studied. The molybdenum powder morphology was examined using high-resolution scanning electron microscopy. The powder phases were analyzed by X-ray diffraction. The tap density and apparent density of the molybdenum powder were investigated using a Hall flow meter and a Scott volumeter. The optimal process parameters for the spherical molybdenum powder preparation are 50 g/min powder feeding rate and 0.6 m^3/h carrier gas rate. In addition, pure spherical molybdenum powder can be obtained from irregular powder, and the tap density is enhanced after plasma processing. The average size is reduced from 72 to 62 μm, and the tap density is increased from 2.7 to 6.2 g/cm^3. Therefore, RF plasma is a promising method for the preparation of high-density and high-purity spherical powders.

Set methods of left-turn waiting zone at signalized intersection

To maximize the number of vehicles passing by the stop-line in a cycle and improve the operation efficiency of intersection in China, the settlement of left-turn lane waiting-zone is becoming prevailing. Based on conflicting-point method, the internal mechanism of left-turn flow after stopping line was analyzed through taking postposition left-turn lane waiting-zone intersection for instance. The relationship between the first left-turn vehicle and the last vehicle of previous phase passing the conflicting point was expounded. According to the time of successive arriving of two vehicle flows at conflicting-point, the reasonable layout for waiting area of left-turn vehicles was researched when the clearance index was less than O. The results suggest that the appropriate layout for waiting area of left-turning vehicles can improve the operation efficiency of intersections.

Anisotropy of Expansion Coefficient and Slag Resistance of Spinel Carbon Bricks

Effects of the pressure direction on the thermal expansion and slag corrosion resistance were investigated and anisotropic microstructures of flaky graphite in spinel carbon bricks were examined. The experimental results show that slag corrosion velocities in the direction parallel to the pressure direction display a decrease of 34% compared to those in the vertical direction. Meantime, the linear expansion coefficient in the direction parallel to the pressure direction is 2.45 times as large as that in the vertical pressure direction. Slag corrosion velocities of spinel carbon bricks soaked in the AOD melting slag display a 46%-47% decrease compared to those of magnesia carbon bricks. The microstructure observation shows that spinel carbon bricks have a high degree of preferred orientation.

Prediction of thermal environment via revision of PMV index with body temperature

PMV(Predicted Mean Vote) is a widely used index for evaluating the thermal environment.However,few studies have been conducted to take physiological values directly as evaluating indices.This paper assumes a linear relation between body temperature and both sweating rate and heat produced by shivering,and introduces the linear relation into the human heat balance equation to revise the classic PMV.And the assumption of linear relation is subsequently proved.The revised PMV possesses the same characteristic of dependent heat load as that of the classic one,and moreover it is convenient to be calculated.

Effects of Loading Rate on Flexural-tension Properties and Uniaxial Compressive Strength of Micro-surfacing Mixture

The major objective of this research was to discuss the effects of loading rate on the flexural-tension properties and uniaxial compressive strength of micro-surfacing mixture using three-point bending test and uniaxial compressive test respectively. As a preventive maintenance surface treatment on asphalt pavement, micro-surfacing was formed on the basis of the ISSA recommendation of an optimum micro-surfacing design. Tests were conducted over a wide range of temperature to investigate the difference of properties from low loading rate to a relatively high loading rate. Three-point bending test was used to study the flexural strength, strain and modulus of micro-surfacing mixture, and uniaxial compressive test was carried out to obtain the relationship between strength and the loading rate as well as temperature. The experimental results showed that flexural strength at high loading rate was larger than that at low loading rate. The flexural strength difference between low and high loading rate enlarged when the temperature rose. The flexural strain at high loading rate increased compared with results of the low loading rate. Results of the flexural modulus revealed that micro-surfacing mixture exhibited better anti-cracking characteristic at low temperature when given a relatively low loading rate. Results of uniaxial compressive test revealed that the strength difference of micro-surfacing among different loading rates increased with the increase of temperature. The logarithm relationship between the strength and loading rate over a wide range of temperature was obtained to compare the experimental and predicted values, which resulting in a reasonable consistency.

NONLINEAR STABILITY OF BALANCED ROTOR DUE TO EFFECT OF BALL BEARING INTERNAL CLEARANCE

Stability and dynamic characteristics of a bail bearing-rotor system are investigated under the effect of the clearance in the ball bearing. Different clearance values are assumed to calculate the nonlinear stability of periodic solution with the aid of the Flo- quet theory. Bifurcation and chaos behavior are analyzed with variation of the clearance and rotational speed. It is found that there are three routes to unstable periodic solution. The period-doubling bifurcation and the secondary Hopf bifurcation are two usual routes to instability. The third route is the boundary crisis, a chaotic attractor occurs suddenly as the speed passes through its critical value. At last, the instable ranges for different internal clearance values are described. It is useful to investigate the stability property of ball bearing rotor system.

High-Pass Block Replacement Attack of Watermarking

To improve the watermark benchmarks database,a new BRA(Block Replacement Attack)method is introduced in this paper.Unlike the typical BRA which exploits the self-similarity among blocks in image,the scheme utilizes the self-similarity in various scale and orientation bands in the wavelet domain of the image.They search the replacement blocks from the blocks of the smaller sub-image at the next lower resolution.The most important advantage of this scheme is that the pyramid sub-band decomposition acts as an automatic block classifier,with the result of simplifying the block search and block matching procedures and thus making the block replacement more effective.Furthermore,an improved algorithm based on Fuzzy set theory is introduced in which the number of blocks chosen for combination are modified adaptively to obtain the candidate replacement blocks.It simplifies the procedure for searching the candidate replacement blocks.These advantages are confirmed by the experimental results,which show that the performance of the scheme is superior to typical BRA methods.

Improving Hydration Resistance of MgO-CaO Clinkers by Depositing MgO Coating

By carbothermal reduction of Mg O with black carbon as reduction agent at a high temperature,Mg O was deposited on the surface of Mg O- Ca O clinker（ as coating） to improve the clinker ＇s hydration resistance. In the paper,effect of deposition temperature and holding time on the hydration resistance of the treated Mg O-Ca O,the deposition mechanism and Mg O coating kinetics were investigated with hydration resistance test,X-ray diffractometry（ XRD） and scanning electronic microscope（ SEM）. Results showed Mg O coating grew in a2D mode on the surface of Mg O- Ca O particles; the Mg O coating improved the hydration resistance of the coated Mg O- Ca O clinker,and the coated clinker would become stronger when coated at higher deposition temperature and longer holding time. The measurements also found that Mg O deposition process varied with the deposition temperature： it was mainly a chemical-controlled process at temperatures between 1 400- 1 500 ℃,with an apparent activation energy（ AAE） of 97. 8kJ·mol^（-1）; it would change into a diffusion-controlled process when the temperature rising to 1 500- 1 600 ℃,with apparent activation energy of 19. 2kJ·mol^（-1）.

The research of breakdown structure and coding system for construction project

Whether the breakdown structure and coding system of construction projects are reasonable or not determines to a large degree the performance level of the entire project management. We analyze in detail the similarities and differences of two kinds of decomposing methods classified by type of work and construction elements based on the discussion of international typical coding standards system designing. We then deduce the differential coefficient relation between project breakdown structure (PBS) and work breakdown structure (WBS). At the same time we constitute a comprehensive construction project breakdown system including element code and type of work code and make a further schematic presentation of the implementation of the system’s functions.

Trinomial tree model of the real options approach used in mining investment price forecast and analysis

In order to effectively avoid the defects of a traditional discounted cash flow method, a trinomial tree pricing model of the real option is improved and used to forecast the investment price of mining. Taking Molybdenum ore as an example, a theoretical model for the hurdle price under the optimal investment timing is constructed. Based on the example data, the op- tion price model is simulated. By the model, mine investment price can be computed and forecast effectively. According to the characteristics of mine investment, cut-off grade, reserve estimation and mine life in different price also can be quantified. The result shows that it is reliable and practical to enhance the accuracy for mining investment decision.

Effect of Waterscape Structures on Nitrogen and Phosphorus Removal Efficiency in Revetment Wetland System

The effect of aeration and waterscape structures reaeration system on nitrogen and phosphorus removal efficiency in revetment wetlands was studied by laboratory simulation. The results showed that the removal efficiency of TN, TP in tranquil flow waterscape was 61% and 72%; aeration and waterscape structure system promoted nitrogen and phosphorus removal efficiency in revetment wetland through increasing the DO content in the water, compared with system without artificial oxygen, the removal efficiency of TP in waterscape structures increased by 11. 6%-19. 1%, and that of TN increased by 10.5%-16. 1%; meanwhile, disturbance brought by the waterscape structure systems enhanced the adsorption of TP and flocculation effect; in addition, nitrification was confirmed as the main control step of TN removal in revetment wetland system.

The Illation of Recreational Culture in The City Public Space

By the comprehension of recreational culture in contemporary, this paper points out it has taken an effective effect on public space, haven the importance and the meaning of design in practical life. At the same time, this article puts forward the conceive technique in the degree of design, and analyzes the skill of illation of recreational culture in the city public space.

一等奖：重生之愿景--玉华煤矿生态景观修复策略

介绍了2014年第51届国际风景园林师联合会(IFLA)国际大学生设计竞赛一等奖作品的创作过程和主要内容。该方案选取陕西省铜川市废弃的玉华煤矿为设计对象,针对其所面临的水土流失、泥石流灾害、煤矸石和矿坑水体污染、山体剥离等问题,通过分区规划与景观设计的手段,结合多学科理论,提出了综合性的修复策略,以期在玉华煤矿实现循序渐进的生态修复和可持续发展的景观模式。

The Future Resources for Eco-building Materials:Ⅱ. Fly Ash and Coal Waste

To use fly ash and coal waste effectively, the current technologies for reprocessing and recycling these wastes into eco-building materials were reviewed, such as utilizing fly ash as the component of fly ash cement and low heat cement after the processes of separation, removal of carbon remains and fine comminution, calcining coal waste into kaolin and meta-kaolin with suspension technology, and preparing clinkerless alkali-activated geopolymer materials with fly ash and meta-kaolin.

Factors affecting biological denitrifying dephosphatation in anaerobic/anoxic/aerobic sequencing batch reactor

This study was conducted to verify and discuss the denitrifying dephosphatation under different levels of nitrate concentration and retention time of anoxic/aerobic process in a Sequencing Batch Reactor (SBR). The results of tests demonstrated that there were two kinds of phosphorus-accumulating organisms (PAOs) in the biological excess phosphorus removal (BEPR) system. One was non-DNPAOs that could only use oxygen as terminal electron acceptors, the other was denitrifying PAOs (DNPAOs) that could use both nitrate and oxygen as terminal electron acceptors. Phosphorus uptake efficiency could be attained under anoxic period ranging from 28.7%-96.7% in an anaerobic/anoxic/aerobic system. Experimental results showed that nitrate concentration and retention time of anoxic/aerobic process were the key factors affecting the course of denitrifying dephosphatation.